How do you remove a stuck bump knob?
- Turn off the Ryobi trimmer.
- Hold the spool of line in one hand and rotate the bump knob counterclockwise.
- Remove the knob.
- Let the trimmer come to a complete stop.
- Locate the two opposite tabs on the sides of the spool retainer.
- Pull up on the old spool to remove it.
How to fix a stuck bump knob?
If the bump knob is stuck, use a pair of pliers for a more secure grip. Be careful when using pliers since the teeth on metal pliers can cut into plastic. If you are concerned, you can opt for taping the teeth of the pliers with Teflon tape to ensure it does not cut into the bump knob.
How do you remove a bump knob on a lawn mower?
Pull straight out to remove the bump knob from the hub. You may have to pull hard to remove the knob. For weed eaters with screw mounted bump knobs, grasp the outer spool and hold it in place with one hand. Use your other hand to twist the bump knob counterclockwise until it unscrews from the spool.
How do I remove the bump knob on my eyebrow Trimmer?
Then, lay it on its side. For clockwise-rotating trimmers, the bump knob should be removed by twisting it off counterclockwise. Bump knobs on counterclockwise-rotating trimmers should be removed by twisting clockwise.
How do you fix a frozen bump knob on a weed trimmer?
If there is no damage to the bump knob and spring or if you have purchased replacements, you can then reassemble the weed trimmer. To ensure that the bump knob does not freeze again, spray a lubricant, like silicone, where the bolt's threads exit the knob.
How do you remove a Ryobi bump knob?
0:041:20The two retaining tabs to release the lower trimmer head housing lift the spool out of the housing.MoreThe two retaining tabs to release the lower trimmer head housing lift the spool out of the housing. And you can detach the old bump knob.
How do I get a stuck bump out of my head?
0:543:46So to cut it off I'm going to use a fairly sharp chisel. And just break through the plastic on both.MoreSo to cut it off I'm going to use a fairly sharp chisel. And just break through the plastic on both. Sides.
How do I change a bump knob on greenworks?
0:191:19Use a flathead screwdriver to help detach the old bump knob if still intact then rotate to remove.MoreUse a flathead screwdriver to help detach the old bump knob if still intact then rotate to remove. You're now ready to install the new bump knob.
How do you replace a bump on a spool?
1:365:24And it doesn't matter which side it goes through you just need to feed it right through. So I wantMoreAnd it doesn't matter which side it goes through you just need to feed it right through. So I want to push that right through till it pops out the other end. And then we're going to pull it.
How do you remove a strimmer cap?
0:172:03Depress the two retaining tabs to release the lower trimmer head housing. Lift the spool out of theMoreDepress the two retaining tabs to release the lower trimmer head housing. Lift the spool out of the housing. And detach the bump knob.
How do you remove the head of a grass trimmer?
1:403:23So to loosen it we turn it clockwise. This is how the way it is usually on most straight shaftMoreSo to loosen it we turn it clockwise. This is how the way it is usually on most straight shaft trimmers all right it's all loose.
How do you change the string on a 40v greenworks trimmer?
0:062:07You'll see that the inlet where the line goes there's some lines on top now line that up with yourMoreYou'll see that the inlet where the line goes there's some lines on top now line that up with your tap and go which is a piece you can actually turn. So just line up the lines.
How do I contact greenworks?
If you have questions or need further assistance, feel free to call us toll free at 1-888-909-6757.
How does a bump feed trimmer work?
0:140:46This design allows the operator to release line when required. Without having to turn the MachineMoreThis design allows the operator to release line when required. Without having to turn the Machine off the bump head is tapped on the ground while spinning. And the centrifugal force releases.
How do you change a head on a trimmer?
0:001:46This I went to the hardware store and I get a replacement kit for the head and I'm going to show youMoreThis I went to the hardware store and I get a replacement kit for the head and I'm going to show you the steps to change this out all right for this model. We need to remove. The old head.
How do you feed a bump feed?
2:085:03Direction. I put my finger in between both lines and then we can just wrap that there. On. GetMoreDirection. I put my finger in between both lines and then we can just wrap that there. On. Get almost to the end. Okay and then you'll notice there's a little notch.
What to do if bump knob is stuck?
If the bump knob is stuck, use a pair of pliers for a more secure grip. Be careful when using pliers since the teeth on metal pliers can cut into plastic. If you are concerned, you can opt for taping the teeth of the pliers with Teflon tape to ensure it does not cut into the bump knob.
How to keep bump knob from freezing?
To ensure that the bump knob does not freeze again, spray a lubricant, like silicone, where the bolt's threads exit the knob. Twist the bolt to distribute the lubricant evenly. Next, clean and remove any grass and dirt from the inside of the outer spool housing .
Why does my bump knob freeze?
If there is any damage to the spring, it is most likely the cause of the bump knob freezing and would need to be replaced. If the inner spring appears intact, inspect the bolt at the top of the bump knob. If all is working correctly, the bolt should spin with little resistance.
Which way do string trimmers spin?
Standard string trimmers will spin clockwise, while brush cutters will spin counterclockwise. Before you remove the bump knob, make sure there is no power running to the engine by either turning off the trimmer or unplugging it. Then, lay it on its side.
How To Troubleshoot the Stuck Trimmer Head?
Here we’ll describe how the trimmer’s different parts can be responsible for the head not spinning. And what you can do to solve this problem. So, let’s get started-
Frequently Asked Questions
Answer: Grab some pliers, squeeze the axle tightly, twist the cap and it’ll do the work.
Conclusion
So, which part of your Stihl trimmer is the reason your stihl trimmer head stuck? I hope our suggestions helped you to figure it out.