While they are soaking, remove the starter cable from the terminal, which is covered by a protective plastic boot. Use a flat head screwdriver to remove the boot and then remove the 12mm bolt that attaches the cable to the terminal. Crawl under your truck and use a 12mm ratchet with extension to remove the two mounting bolts on the starter.
How do you change the starter on a Toyota 4Runner?
- Turn off the ignition and remove the negative battery cable from the battery.
- Remove the positive cable (the large cable that runs to the battery) from the starter.
- Disconnect all the bolts that hold the starter to the block, using a ratchet.
- Remove any other supporting brackets holding the starter in place.
Where is the reset button on a Toyota 4Runner?
there is no reset button. if all your tires are up to spec psi, there will be no light. if there still is, then you have a bad sensor or sensor communication issue. I just checked the manual. The tire tech may have stated to hit the reset button because other Toyota models do have a reset button.. the 4Runner does not. 1. Low tire pressure 2.
Is Toyota 4Runner a good family car?
This ample room for family road tripping, gear toting, and nearly anything else an active family needs to haul around. The Toyota 4Runner is a safe and reliable off-roader for families. For the duration of its current fifth generation, the Toyota 4Runner SUV has received nothing lower than a 4 out of 5 for reliability from Consumer Reports. Most years it earns a 5 out of 5.
How to replace the battery in a Toyota 4Runner?
Battery Replacement: 2010-2021 Toyota 4Runner SR5 4.0L V6
- Getting Started - Prepare for the repair
- Open the Hood - How to pop the hood and prop it open
- Access Battery - Learn where the battery is located
- Remove Bracket - Take off the bracket that secures the battery
- Remove Cables - How to disconnect the cables the right way
- Clean Cables - Clean with baking soda, water and a wire brush
See more
How do you remove the starter on a 3rd gen 4Runner?
1:528:273rd Gen 4Runner 3.4L 4WD Starter Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipTransmission then there was two bolts that we had to remove which we got to from the bottom side ofMoreTransmission then there was two bolts that we had to remove which we got to from the bottom side of the passenger side of the car these two bolts are holding in the actual starter.
Where is the starter located on a Toyota 4Runner?
2:569:14How to Replace Starter 2003-09 Toyota 4Runner - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere we go the starter is held on by this bolt right here and then there's one up top which you canMoreThere we go the starter is held on by this bolt right here and then there's one up top which you can not see very well that one right here both 14 millimeter bolts. So let's take.
How do you remove the starter on a 1998 Toyota 4Runner?
Locate the two starter-mounting bolts at the front of the starter where the starter meets the bell housing. These bolts slide in from the back, or transmission, side of the bell housing. Remove them with a socket and ratchet while supporting the starter motor. Lower the starter and remove it from under the truck.
How do you take a starter off?
How to Replace a StarterSafety First. Disconnect the battery. ... Remove the Wiring. Remove the wiring and positive battery cable from the starter solenoid.Remove the Starter and Bolts. Remove the starter retaining bolts. ... Compare to Verify. ... Transfer Heat Shield. ... Replace with New Starter. ... Secure and Tighten. ... Connect the Wiring.More items...
How much does it cost to replace a starter on a Toyota 4Runner?
The average cost for a Toyota 4Runner starter replacement is between $395 and $553. Labor costs are estimated between $195 and $246 while parts are priced between $200 and $307.
Where is the starter located on a 1998 Toyota 4Runner?
2:157:10How to Replace a Starter on a 1998 Toyota 4Runner - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay the starter is located on the passenger side of the engine.MoreOkay the starter is located on the passenger side of the engine.
Where is the starter located on a 1997 Toyota 4Runner?
0:1513:24Seth is becoming a Mechanic | 1997 4Runner Starter ReplacementYouTubeStart of suggested clipEnd of suggested clipSometimes turn the key and it goes click. But nothing the battery's.MoreSometimes turn the key and it goes click. But nothing the battery's.
How much is a starter for a 98 Toyota 4Runner?
Compare with similar itemsThis item New Starter Replacement For 1996-2000 Toyota 4Runner 2.4L 2.7L, 1994-1998 Tacoma & T-100 T-150 2.4L 2.7L 281000010084, 28100-0C010, SND0104, 41052042, 41052042RCustomer Rating4.5 out of 5 stars (21)Price$12995ShippingFREE Shipping. DetailsSold ByOEG Parts2 more rows
How do you remove a starter from a Toyota Tundra?
5:4215:17How to Replace Starter 2007-Present Toyota Tundra 4WD - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you just go ahead and follow it down along where it runs alongside of the engine. You're goingMoreSo if you just go ahead and follow it down along where it runs alongside of the engine. You're going to find a mounting bolt right here let's go ahead and remove.
What tools do I need to remove a starter?
Tools needed to replace a starter:Sockets and wrenches.Screwdriver.Pliers.Battery terminal puller.Drive-on ramps, jack or jackstands.
Can I replace the starter myself?
You can buy a new starter, which is rather expensive, or you can buy a rebuilt starter, which is just as good as a new one [source: Allen]. If the problem is really your starter, save yourself a trip to the mechanic and replace it yourself.
How long does it take to change a starter?
between 2 and 4 hoursDue to the complexity of starter motors, the average amount of time it takes to completely replace a starter is generally between 2 and 4 hours. If your car has an easily accessible starter and you take it to a mechanic worth their salt, your time should hopefully be closer to 2 hours rather than 4.
How to remove the starter from a transmission?
Remove the starter mounting nuts that fasten the starter to the transmission, using a socket. Support the starter while you remove the bolts. Pull the starter out of the engine bay.
How to remove engine shield on 4Runner?
Remove the lower engine shield if your 4Runner is equipped with one. Use a socket and ratchet to remove the shield.
How to remove battery cable from starter?
Remove the nut that holds the battery cable to the starter solenoid, which is the smaller round part attached to the body of the starter. Unplug the wire that clips into the solenoid by pulling it out.
Does the 2000 Toyota 4runner have a starter?
The 2000 Toyota 4Runner is a well-known SUV was a hit for Toyota. Combining reliability, practicality, utility and style, the midsize SUV developed a loyal group of followers. But like any consumer vehicle, there are parts on the 2000 Toyota 4Runner that wear out. The starter is one such part. If you 2000 4Runner's starter goes out and you want to start it without pushing it down a hill, you'll need to replace the starter.
How to reinstall a starter?
Reinstalling the starter is much easier than the job of taking it out. Turn it and put it back in position, be sure to reconnect the switch cable before remounting it. Use your 12mm ratchet with extension to tighten the mounting bolts. Replace the cable bolt and boot cover. Reinstall the transmission fluid dipstick, and brake line with your 12mm ratchet or wrench. Put the intake tube back in place up top. Replace the splash guard, re-mount your wheel and snug the lugs before dropping the truck. Once on the ground, tighten and torque the lugs.
Why is my 4runner not turning over?
If you can't get your 4Runner to turn over, or it cranks very slowly, it could be a bad starter. If the battery tests good, and all the wiring looks good, the next logical cause is the starter itself. It's also a possibility that the starter could still be good, but it may just need a good cleaning. Tearing apart your starter and cleaning it isn't ...
How to remove a starter cable from a truck?
While they are soaking, remove the starter cable from the terminal, which is covered by a protective plastic boot. Use a flat head screwdriver to remove the boot and then remove the 12mm bolt that attaches the cable to the terminal. Crawl under your truck and use a 12mm ratchet with extension to remove the two mounting bolts on the starter. Hopefully the penetrating spray will make this job a little easier. Once the bolts are off, you will have to turn the starter to finagle it out of position and remove the switch cable before pulling it from the truck from below and out through the wheel well, as the manifold will prevent you from taking it out from above.
Is a starter bad?
In many cases, the entire starter may not be bad. The contacts on the plunger could be very gummed up and nasty. Brake cleaner and a steel wire brush may clean the contacts enough to allow months or years more service out of the starter. See the link at the bottom for an in-depth explanation of how to clean it.
Can you clean a starter on a truck?
It's also a possibility that the starter could still be good, but it may just need a good cleaning. Tearing apart your starter and cleaning it isn't too difficult, but no matter what, you'll have to take it off the truck to fix it.
Can you change a dead starter on a 4runner?
Changing out a dead starter on a 4Runner isn't all that hard. Not only will it save you money, but you'll have the pride of a job well done. This article applies to the Toyota 4Runner (1996-2002). If you can't get your 4Runner to turn over, or it cranks very slowly, it could be a bad starter. If the battery tests good, and all ...
How to unscrew top bolt on starter motor?
Put the socket and the extension behind the cables and feel your way in to the top bolt of the starter motor. When the socket is securely on the bolt, use a ratchet to unscrew the top bolt.
How to remove starter from wheel well?
Find the starter motor behind the wheel well where you just removed the wheel. Remove the nut holding the cable to the starter motor and pull off the cable. Remove the starter from the side hole in the wheel well. This is a small hole so have patience working it back and forth until it comes out.
How to find the starter cable?
The cable can be found by tracing a thick cable from the positive side of the battery (usually indicated with red color) down to the starter motor. This cable is thick since this is where the starter motor gets the power to crank the engine and that consumes a lot of energy.
Where is the bolt on a starter motor?
Figure 4. Lower bolt holding the starter motor (the bolt is at the red arrow). This is seen from the right wheel well.
How to remove signal wire from starter motor?
Squeeze the connector of the signal wire and pull it off from the starter motor.
Where is the positive cable on a starter motor?
Here is the positive cable on the starter motor. The upper red arrow points at the starter motor and the lower red arrow points at the nut holding the positive cable. This is seen from the right wheel well.
What year was the Toyota 4Runner V6?
This article applies to the Toyota 4Runner V6 (1984-1995).
