How to Remove Compression Fitting from Pipe
- Shut off the water to the pipe from which you are going to remove the compression fitting.
- Hold the male end of the fitting steady with a pair of adjustable pliers. If you are removing a shutoff valve with a compression fitting, the ...
- Turn the compression nut counterclockwise relative to the male part of the fitting with another pair of adjustable pliers. When you are removing a ...
- Grip the ferrule with one of the pairs of pliers and turn it a few times to loosen it. Try pulling it off the end of the pipe. If you are lucky ...
Full Answer
How do you remove a ferrule from a compression valve?
Alternatively, if your saw has enough clearance, you can cut through the ferrule, being careful not the cut into the pipe underneath, and pry it off. If you're replacing a compression valve, you should always remove the old ferrule and slide on a new one when you screw on the new valve.
How do you remove a compression fitting from a water pipe?
You usually have to cut it off. Shut off the water to the pipe from which you are going to remove the compression fitting. Hold the male end of the fitting steady with a pair of adjustable pliers. If you are removing a shutoff valve with a compression fitting, the valve has the male part of the fitting, so hold it with the pliers.
How do you disassemble and reassemble a ferrule?
Disassembly involves simply loosening the compression nut or screw. Re-assembly can be accomplished in a similar manner to the initial assembly, although typically fewer turns of the nut are required, since the ferrule is already swaged to the tubing.
How do you remove a ferrule from a copper pipe?
In most cases, however, you'll have to cut it off. Cut through the pipe as close as possible to the back of the ferrule with a hacksaw. When the ferrule falls off, deburr the end of the pipe with a file and slide off the compression nut.
How do you remove a compression fitting from a ferrule?
2:575:11How to Remove a Stuck Ferrule from a Copper Pipe in Seconds - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround the threads of the tool. I want to tighten this up a little bit. Doesn't you don't have toMoreAround the threads of the tool. I want to tighten this up a little bit. Doesn't you don't have to over tighten it just tighten it up a bit.
How do you remove a stubborn compression fitting?
1:202:52Compression Ring Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd place the forks of the puller behind the compression ring and nut. Next turn the puller handleMoreAnd place the forks of the puller behind the compression ring and nut. Next turn the puller handle clockwise until the compression ring and nutter pulled loose from the copper. Pipe.
How do you remove a ferrule tube?
Grip the nut closest to the wall or floor with a pair of pliers. Hold onto the front of the angle stop so it stays in place. Turn the nut clockwise to loosen it from the angle stop. Then you can turn the nut by hand until it detaches from the angle stop to reveal the ferrule wrapped around your pipe.
Can you unscrew a compression fitting?
Turn the compression nut counterclockwise relative to the male part of the fitting with another pair of adjustable pliers. When you are removing a shutoff valve, this means turning the nut clockwise with respect to you. Once the nut is loose, unscrew it by hand until the fitting separates.
Can you reuse compression ferrule?
Ferrule can never be reused once they have been compressed. This connector is directly placed over the pipe and the nut is tightened compressing the ferrule between the pipe and the body of the fitting.
Can you overtighten a compression fitting?
Hold the compression fitting body tightly with a pair of grips and tighten the nut with a spanner. Its often said in the trade to not over tighten a compression fitting, leaving you more thread in the case of a leak and not distorting the olive or fitting. Generally a nut will need one whole turn after hand tightening.
How do you use a ferrule puller?
0:251:30Easy Compression Ring Removal - Superior Tool Handle & Sleeve PullerYouTubeStart of suggested clipEnd of suggested clipAnd the compression ring that has probably been on there for many years simply attach the nut to theMoreAnd the compression ring that has probably been on there for many years simply attach the nut to the threaded portion of the gold ferrule on the tool. And then turn the handle in a clockwise motion.
How do I uninstall Swagelok ferrule?
0:021:28How to Replace a Stainless Steel Ferrule on Stainless Steel TubingYouTubeStart of suggested clipEnd of suggested clipScore the tubing by slowly rotating the tubing cutter in a counterclockwise. Direction remove theMoreScore the tubing by slowly rotating the tubing cutter in a counterclockwise. Direction remove the tubing cutter.
How does a ferrule fitting work?
0:266:10How compression fittings work - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that is a fitting you'll see that it is recessed on the inside of there when you push the tubeMoreSo that is a fitting you'll see that it is recessed on the inside of there when you push the tube into the fitting the olive then slides up and fills that gap.
How do I remove a compression fitting hose?
Cut the hose about 1 inch from the fitting if it cannot be pulled apart. Slice long ways through both sides of the hose up to the edge of the fitting. Grasp the hose with a pair of needlenose pliers and twist and pull it until it comes out.How to Remove the Hose in Soaker Hose Compression Fittingshttps://homeguides.sfgate.com › remove-hose-soaker-hose...https://homeguides.sfgate.com › remove-hose-soaker-hose...Search for: How do I remove a compression fitting hose?
How do you release a pressure fitting?
0:081:08How to remove Push to Connect fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust use a wrench. This is a 3/4 inch line 13/16 wrench just push it on here this is really chewedMoreJust use a wrench. This is a 3/4 inch line 13/16 wrench just push it on here this is really chewed up but it'll go on the other end too just going to give it a good push on.How to remove Push to Connect fittings - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you release a pressure fitting?
How do you remove a metal compression fitting from plastic tubing?
To remove the compression fitting from plastic tubing you'll need two crescent wrench. Place one on the fitting body and another on the metal nut. Twist it counterclockwise until it comes off. Pull out the tubing from compression fitting.How To Remove Compression Fitting From Plastic Tubing [Details ...https://homearise.com › remove-compression-fitting-plasti...https://homearise.com › remove-compression-fitting-plasti...Search for: How do you remove a metal compression fitting from plastic tubing?
What is compression fitting?
Compression fittings allow you to make connections to copper pipes without soldering them. They are especially useful for shutoff valves, such as the ones for your sinks and toilets. A compression fitting has three parts: a nut with female threads that screws onto a seat with male threads and a brass ring, or ferrule, that fits between them.
How to remove a shut off valve?
When you are removing a shutoff valve, this means turning the nut clockwise with respect to you. Once the nut is loose, unscrew it by hand until the fitting separates. Grip the ferrule with one of the pairs of pliers and turn it a few times to loosen it. Try pulling it off the end of the pipe.
How to loosen a ferrule from a pipe?
Grip the nut closest to the wall or floor with a pair of pliers. Hold onto the front of the angle stop so it stays in place. Turn the nut clockwise to loosen it from the angle stop. Then you can turn the nut by hand until it detaches from the angle stop to reveal the ferrule wrapped around your pipe.
How to pull a nut off a pipe?
Hold the puller’s arms against the back of the nut. Bend the arms toward the pipe so they wrap around the backside of the nut. Squeeze the arms tightly around the pipe and hold them in place with your nondominant hand. That way, the arms will apply pressure to push the nut and ferrule off of the pipe.
How to remove a ring from a puller?
Turn the puller’s handle clockwise to remove the ring. Hold the arms in place with your nondominant hand and operate the handle with your dominant hand. Keep spinning the handle clockwise so the nut and ferrule slide toward the end of the pipe. When they reach the end, the ferrule and nut will fall off.
What is a ferrule on a drain valve?
Learn more... If you’re replacing a drain valve on a sink or toilet, you might come across a metal compression ring, or ferrule, that’s stuck on your pipe. Ferrules prevent pipes from splitting, but they can be pretty hard to remove since they fit so snugly.
How to use a compression nut on a puller?
The central column of the compression puller has a threaded end that holds the nut tightly against the ferrule. Hold the compression nut against the threading and turn it counterclockwise by hand.
How to get water out of a water pipe?
1. Turn off your water supply. Since you’re removing the valve from the pipe, water will spray out from the pipe if you leave the supply on. You’ll typically find your main water supply valve in a basement, garage, or utility room, but it may be along an exterior wall as well.
How to get water out of toilet tank?
Turn on the faucet or use the fixture that’s connected to the pipe you need to access. Let the water flow until you don’t see anything coming out from the faucet anymore. If you’re working on a toilet valve, keep flushing the toilet until there isn’t any water in the tank.
What is the radial compression of a ferrule?
It is this radial compression that creates the leak tight seal between the fitting, ferrule, and tubing, and gives the compression fitting its name. ...
What is compression fitting?
Compression fittings are one of the most common and versatile methods of connecting metal or hard plastic tubing. Particularly useful for their extreme temperature and pressure capabilities, and their compatibility with aggressive fluids, compression fittings can be seen in systems varying from gas lines in refineries, ...
What is a single ferrule?
Most basic compression fittings contain a single ferrule. Single ferrule designs minimize the total number of components, and work reliably when fabricated from softer materials (plastic or brass for example). With harder materials like steel however, torque is often transferred from the compression nut to the ferrule as the nut is tightened.
What is the importance of the shape of the ferrule and the mating angle of the fitting body?
The shape of both the ferrule and the mating angle of the fitting body are critical factors in the reliability of a compression seal. Both components must be tapered in a manner that allows the ferrule to compress properly as the nut is tightened, while maintaining axial alignment with the tubing.
What is a ferrule?
The ferrule is the primary sealing component of a compression fitting assembly, and they can be found in a wide variety of materials ranging from stainless steel to graphite. The majority of ferrules in the marketplace however, are manufactured from metals.
How does metal tubing affect compression?
The way in which metal tubing is produced can have a significant effect on its performance with compression fittings. Tubing should be smooth and free of roughness or extrusion lines that can create a leak path past the ferrule. Furthermore, tubing that has been stored in coils can often have an asymetrical diameter, preventing even compression. While an elastomeric seal can deform to match these slight variations, the metal-to-metal seal of a compression fitting is less forgiving. It is also important that the end of each section be squarely cut, to allow the tubing to sit symmetrically in the fitting body.
What is an asymmetric ferrule?
An asymmetrical ferrule is cone shaped, and can only be placed into the fitting body in one direction ( usually with the tip of the cone facing into the fitting body). Symmetrical ferrules look like two cones back-to-back, and can be placed into the fitting body in either direction.
