How to Make a Professional Job when Punching holes
- 1st Put the Belt around your waist and mark where you need the hole with a pen
- Make your pen mark for the new hole is in line with the other belt holes so it looks correct
- As mentioned buy a good set of pliers to punch the hole.
How do you put a hole in a belt?
Put the belt around your waist and determine the area on the belt where you need to add the hole. Mark this area by drawing a small dot that is parallel to the other belt holes. Lay the belt flat on a piece of wood with the outside part of the belt facing up.
How do you punch out a belt?
Use a marker to dot the belt over the area you plan on punching out. If your top priority is a comfortable fit, instead wear the belt and pull it to a comfortable position, then mark the belt where the strap tongue touches it. Hold the belt in place.
How do you fix a broken belt on a belt?
Flip the belt over so that it's backside is facing up. Use a sharp knife to cut and even out any part of the belt material that sticks out due to the nail being driven through it. Apply clear shoe polish to one side of a toothpick. Stick the toothpick into the hole and apply the shoe polish to the sides of the hole to seal it.
How far apart do you punch holes in a belt?
Method 1 Punching a High-Quality Hole. If you are making a belt from scratch, the holes are typically spaced ½" (1.25 cm) apart for belts under ⅜" (1 cm) wide, and up to 1⅛" (2.85 cm) apart for belts above 1" (2.5 cm) wide.
How to drill a hole in a belt?
How far apart should I put a belt hole?
How much does a leather hole punch cost?
How to keep a belt taut?
How to keep a hole tidy?
Can you screw through leather?
See more
About this website
What can I use to punch a hole in my belt?
That's right, all you need is a hammer and nail to get the job done. Even the simplest of toolboxes will have this. Simply find a nail that is similar in size to the holes on your belt, line it up with the mark for your new hole, and drive it through with the hammer.
How do you make a hole in a belt without punching it?
The four best ways to punch holes in belts without using a leather hole punch are to either use a power drill, a heated nail with pliers, an awl with a mallet, or a hand drill. While we always recommend using a hole punch to achieve the best results, you'll be able to use the above tools to achieve a similar result.
How can I make a hole in my belt at home?
Keep your belt stretched firmly (you can hold one side of the belt under you foot, and the other side with one of your hand, while the other hand is holding the pliers) and point the nail to the spot you want to make a hole, and push into the belt. It makes a small regular hole very easily.
Can you poke another hole in a belt?
Add Extra Belt Holes to Your Leather Belt Measures the distance between the holes on the belt to add evenly spaced new holes. Place your punch where you want a new hole. Hammer the punch through the leather. Belt leather is pretty thick, so this may take several blows.
Can Gucci add holes to belt?
Adding Holes To Your Gucci Marmont Belt Have your Gucci store add them for you for free. Get yourself a leather hole punch tool (the same one that the cobbler uses) and add as many holes to as many belts as you like.
How do you punch leather without a leather punch?
0:462:07How to Make a Hole in Leather Without a Leather Punch - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut you take the drill bit out and then where you want it you just kind of spin it in place a fewMoreBut you take the drill bit out and then where you want it you just kind of spin it in place a few times. That's going to make a small pilot hole if you will.
What tool is used to punch holes in leather?
Round drive punchesRound drive punches are thin, cylindrical steel tools used to cut holes in leather. The cutting end is made of a sharpened edge around a hollow metal tip. There is usually an opening in the cylinder near the cutting end. The other end of drive punches is solid steel.
How do you make a hole in a leather belt?
0:412:05FUN Way To Make A Hole In Leather Belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt should be hot enough to do the trick. So then just lay out your belt on something like wood orMoreIt should be hot enough to do the trick. So then just lay out your belt on something like wood or something. And I'm gonna want to adjust about. There. So just stick that bad boy right in there.
How can I make my belt tighter?
2:025:32How to fix a belt to make it fit, this helps if you lose weight ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I just want to go ahead and start the drill. I'm not really trying to be super aggressive to it.MoreAnd I just want to go ahead and start the drill. I'm not really trying to be super aggressive to it. But it is going to Pam I need you to hold it really tight please all right you ready let's go.
How do you use a belt puncher?
The hole punch should be completely perpendicular to the leather. Hold it securely in this position, and hammer straight downwards. Depending on the thickness of the leather, the punch should cut through cleanly with one or two solid blows.
How do you cut a belt?
Cut-To-Fit Belt TutorialWrap the belt around your waist and measure the excess leather. ... Lay the belt flat with the screw facing upward. ... Unscrew the buckle from the waist strap.Remove the buckle from the waist strap. ... Using the previously measured dimensions from step 1, mark off the extra leather.More items...•
How to Make a Hole in a Leather Belt (6 Methods ... - The Art of Manliness
Editor’s Note: This is a guest article by Michael Magnus. Whether putting on a few pounds at the holidays or getting fit and shedding inches with The Strenuous Life, it’s handy to know how to add a new notch or two to your leather belt. In this article, you’ll see several different methods for punching holes: some involve tools that make the job especially easy, while others allow you to ...
Calfskin Leather Hides | The Leather Guy
Calfskin comes in a full spectrum of colors and textures. There is variety of prints, as well, even hair-on! Sizes tend to land around 6-10 square feet, and most are soft in temper.
Customer Care — Tandy Leather, Inc.
Order Status | Find a Store | Return Policy Need help with an order, have a question, or looking for product safety information? Give us a call or send us a message. Customer Service is available Monday – Friday 8AM to 6PM CST to answer your questions or assist you with an order. Call 877-532-8437, Email TLFHelp@tandyl
Measuring the Holes
Regardless of which method of hole-making you choose, you’ll first want to measure out and mark where you want the hole to go.
Adding Rounded Holes to Your Belt
Although there are a number of different ways to perforate leather, simply puncturing it may result in the hole tearing during use.
The Rotary Punch
The rotary punch is perhaps the simplest and most straightforward solution. Tandy Leather makes some rotary punches that are specifically for leather; however, you may be able to find something workable at a regular hardware store.
The Round Drive Punch
This is another tool that if you don’t already have, can be purchased at Tandy or perhaps a hardware store. These sharp steel tubes come in several sizes, but typically you’d want to use the 3/16” size to make holes on a belt for a standard belt buckle.
The Power Drill
The power drill is a tool you likely already have on hand. By using the 3/16” bit, you can carefully drill a hole into the leather. While this seems pretty straightforward, there’s still a little precaution to take here.
Puncturing Holes Into Your Belt
When you have the option, one of the above methods is really your best bet. However, if you’re in a pinch, the following 3 methods can work as well.
The Pocket Knife
As just mentioned, a knife is going to come in handy for finishing out the hole on all 3 of these puncturing options, but you’ll have to be careful if using it to start one. When you use a knife to pierce the leather at your designated mark, the shape of the blade may make it difficult to puncture the leather without making a cut that is too large.
How to make a belt hole?
Put the belt around your waist and determine the area on the belt where you need to add the hole. Mark this area by drawing a small dot that is parallel to the other belt holes. Lay the belt flat on a piece of wood with the outside part of the belt facing up. Place the sharp point of the nail on the mark that you made on the belt and hold ...
How to fix a hole in a belt?
Remove the nail once the hole has been made. Flip the belt over so that it's backside is facing up. Use a sharp knife to cut and even out any part of the belt material that sticks out due to the nail being driven through it. Apply clear sho e polish to one side of a toothpick. Stick the toothpick into the hole and apply the shoe polish to ...
Why do belts have holes?
Belts have numerous holes to allow users to find the best fit for them. Sometimes an extra hole is needed to accomodate the weight loss or weight gain fluctuation that the body often goes through over a period of time.
How to remove a nail from a belt?
Place the sharp point of the nail on the mark that you made on the belt and hold the nail up using your thumb and index fingers. Gently hit the head of the nail with the hammer, hitting harder each time until the nail completely penetrates the belt. Remove the nail once the hole has been made.
How do you poke a hole in a belt with scissors?
Please do not use scissors and drill bits by trying to poke and pierce you way through the material, I cannot tell you the amount of time I have had customers tell me they have injured or ruin an Expensive Belt trying to save money when making additional holes in leather
How to tell what a Good Leather Belt punch is when buying one
The simplest way is the weight just by picking up the pliers is they fell light these will not take the strain buy punching a hole, the punch pliers should have some weight to them, also the hole punching part of the tool should be sharp enough to cut a clean hole.With Cheap and nasty hole punches the frame/ handles of the tool just buckles under pressure and do not have the strength to make a clean cut job..
How Much will a Good Quality Belt Punch cost?
I would recommend spending over £10 to ensure you get one that is of the right quality to stand up to the job, and you will always have it for another time when punching those extra belt holes.I would recommend this hole punch plier everytime.
What is the best way to punch a hole in a stack of paper?
Gather your documents and put them between two boards on a solid work bench. On the top board, draw the holes you’ll need. Now take a drill with a diameter equal to the hole size you want and drill through the top board, the paper, and the bottom board.
How do you make four holes in a sheet of A4 paper?
Place the right side of one piece of A4 paper into the hole punch. The four “punch” tools may be found above where the right side rests. Push down on the lever using one hand’s palm. Press firmly and then release.
Without a hole puncher, how do you create a hole in paper?
If you’re using a three-ring binder, insert paper into the rings and punch through it, or if you don’t want to do that, create an impression on the paper and poke holes with a toothpick. If you’re not using a binder, a toothpick will do. I prefer to make a little triangle with three holes and then remove the centre.
What is the cost of punching a hole in a belt?
If you don’t want to spend $12 on a hole puncher, another alternative is to take your belt to a shoe repair shop. For $5 or less, they should be able to add a hole to your belt.
Is it possible to use a hole punch on a belt?
These sharp steel tubes come in a variety of diameters, but the 3/16″ size is generally used to create holes in a belt for a regular belt buckle. You should be left with a perfectly round hole if you center the punch over the marker and give it a couple good whacks with a mallet.
What are the terms for belt holes?
Steel or other metals are often used for the prong (also known as a pin). The prong of a traditional belt fits through the buckle to hold the material in place at a certain length. In America, the prong is referred to as the buckle’s tongue, as in ‘lock-tongued buckle.’
What is the most effective tool for cutting a leather belt?
Pro super shears may also be used to cut pointed belt points or reduce the length of a belt. Softer leathers, like garment leather, stretch more easily, making it simpler to cut with super shears rather than a utility knife.
How to drill a hole in a belt?
Hold the belt in place. Use heavy objects to weigh down each end of the belt, with the location where the hole will be punched on top of a block of wood or other hard, flat surface. 3. Consider an electric drill. If you have one, an electric drill can be used to drill a hole through the belt, as long as you're careful.
How far apart should I put a belt hole?
If you are making a belt from scratch, the holes are typically spaced ½" (1.25 cm) apart for belts under ⅜" (1 cm) wide, and up to 1⅛" (2.85 cm) apart for belts above 1" (2.5 cm) wide. Position the belt.
How much does a leather hole punch cost?
If you want the new belt hole to be as tidy and discreet as possible, a leather hole punch is by far the best tool. These typically cost less than $10 US at a craft or hobby store.
How to keep a belt taut?
Use heavy objects to keep the belt taut, or have a friend pull the belt taut in front of you. 4. Squeeze hard . Squeeze the arms of the hole punch together tightly and firmly. Some thick belts may require strong hands, or someone to wiggle the taut belt back and forth as you squeeze.
How to keep a hole tidy?
Use these tips to keep the hole tidy: Insert drill bits by hand into the existing holes. Select one that fits smooth ly but tightly into the hole. Use a brad-pointed drill bit if available. If using a smooth drill bit, create a small depression for it to stand in, using a sharp knife or nail.
Can you screw through leather?
A nail will make a smoother hole through a thin belt, but if you're looking to save time, a screw can be turned through the leather, using its threads to tear through faster. Again, be careful of scratching the surface beneath. (Follow the precautions in the previous step.)
