Trim the strips down to 1 inch for the side paneling so that it appears 1 ½ inches wide when butted against the front and back paneling. Cap the lower paneling using small crown molding topped with a 1x shelf. Sheathe the bottom of the post with baseboard.
How do you make a box out of a column?
Build a U-shaped box with 3 sides and secure it well with screws. Hold the box around the column, then screw the fourth side to create a 4-sided box. The shims need to be installed on the bottom or at the top of the box tightly with a hammer to prevent it from moving. Drill a hole on each side of the box 2 feet from the bottom.
How do you cover columns in a basement?
Choosing a way to hide columns is easy. The most conventional design is to box and cover them with decorative wood. To prepare your basement columns to be covered with the wood of your choice, follow these steps. Measure the height of the columns. Make sure your 4 pieces of 1x6x12-inch lumber match those measurements.
How do I make a patio block Mailbox column?
Create a beautiful patio block mailbox column in a few simple steps. Product costs, availability and item numbers may vary online or by market. Product costs, availability and item numbers may vary online or by market. Use a semirigid backing material, such as non-expandable spray foam, as a form for the concrete grouting.
What are column covers?
Column covers come in multiple pieces for reassembly or wrapping an existing post on site. Consider using our accommodating columns in your next project: colonnades, column wraps, column covers or pole covers, basement lally columns, porches, balconies, decks, gazebos and courtyards are all candidates.
How do I make my own column wraps?
0:1423:59Fun and Easy DIY Front Porch Post/Column Wrap - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that will make it easier to put together and faster and less cutting all that i do is cut theMoreSo that will make it easier to put together and faster and less cutting all that i do is cut the lengths. And some notches in the top to fit around some of the beam work and take off lights.
How can I cover my existing porch columns?
0:145:42EASY, DIY FRONT PORCH COLUMN/POST WRAPS TUTORIAL!YouTubeStart of suggested clipEnd of suggested clipSo for starters I'm making my carcass or my enclosing for the wrap. And I'm making them two and aMoreSo for starters I'm making my carcass or my enclosing for the wrap. And I'm making them two and a half feet long from the bottom to this for four by one and for six.
How do you wrap columns in wood?
1:016:12How to Wrap Posts in Cedar Wood | Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight here. And subtract the width of this board from that and then we'll cut a four by four basedMoreRight here. And subtract the width of this board from that and then we'll cut a four by four based off of those dimensions. So we have an inch and 3/4. Then we're going to subtract.
How do you cover an existing porch post?
1:3520:31TRANSFORMING OLD PORCH POSTS | CLEAN AND MODERNYouTubeStart of suggested clipEnd of suggested clipYou could get by with one drill. But i'm using robertson screws to put put it together you can useMoreYou could get by with one drill. But i'm using robertson screws to put put it together you can use whatever you like this is a countersink. That's because we're putting our corners.
How do I cover a column?
Step 1: Cut plywood boards. Our metal columns were 21″ x 1″ x 8′. ... Step 2: Attach a foundation to the top and bottom of the columns. ... Step 3: Attach the plywood boards. ... Step 4: Attach 1″ x 5″ boards to the side. ... Step 5: Attach moldings. ... Step 6: Caulk and fill in with wood putty. ... Step 7: Paint.
How do you update porch columns?
How to Update Porch ColumnsMeasure and pre-fit the wrap: Put the wrap around the Column and measure. ... Install the Wrap: Secure top and bottom of the three-sided wrap with weather-resistant screws hidden by cap and base. ... Install any Caps or Bases: Install in the same manner as the wrap.
How do you wrap a porch column with ribbon?
1:066:27How to Decorate your Porch for Christmas - Wrap Columns Candy ...YouTubeStart of suggested clipEnd of suggested clipThe curling ribbon i use a chair to stand on i just prefer doing that it feels safer to me but ofMoreThe curling ribbon i use a chair to stand on i just prefer doing that it feels safer to me but of course you can use a ladder. If you prefer to do.
How do you wrap a deck post?
1:237:18Build Update: Wrapping More Posts || Dr Decks - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor being able to attach some things so what we do is we take a router. And we route out the areaMoreFor being able to attach some things so what we do is we take a router. And we route out the area that these bolts mostly for these bolts. And i could probably just drill three holes.
How do you make decorative porch posts?
0:045:05How To Build A Porch Column Wrap | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipHey Jeff alright so some figuring to do to build this porch railing system yeah so we've got aMoreHey Jeff alright so some figuring to do to build this porch railing system yeah so we've got a decorative column wrap that's going on our you know six by six posts that are existing there we've got a
What can I do with old porch columns?
Ideas for Repurposing an Antique ColumnTurn it into a Welcome sign for the front porch.The obvious – backpacks, coats, scarves and hats.Add framed pictures for a unique display.Top it with a birdhouse.Hang plants or bird feeders from the hooks.Use it for jewelry.Turn it into a table.Turn it into a floor lamp.More items...
What kind of wood do you use to wrap porch columns?
Almost any type of wood works fine for square or rectangular columns. For economy or paint-grade, use fir or yellow pine. For high-end columns, use hardwoods such as birch, mahogany or white or red oak. As with any type of exterior wood, proper sealing and maintenance is required.
How do you cover a wrought iron porch column?
Cut plywood boards. Our metal columns were 21" x 1" x 8'. ... Attach a foundation to top and bottom of the columns. We then attached 1" x 1" boards on either side of the column at the top. ... Attach the plywood boards. ... Attach molding and caulk and fill in with wood putty. ... Grab your sprayer. ... Add paint and begin. ... Enjoy the new look!
Step 1: Cut Boards to Length
Cut four 1x6 boards to length based on the ceiling height. These will be the column shaft.
Step 2: Cut and Install Bottom Blocking
Cut four pieces of the 1x1 to 1-1/2”. Center each piece on the inside bottom of each 1x6. Nail the blocking to the 1x6. Test fit that the four pieces will connect and wrap snugly around the column. The blockers should butt against the existing column and also touch each other.
Step 3: Cut and Install Top Blocking
Cut two pieces of the 1x1 to 5-1/2”. Nail each piece to opposite sides of the soffit, butting them against the existing column. Make sure the blocking is attached to the exact spot you want the columns to be.
Step 4: Nail On the 1x6s
Mina Starsiak of Good Bones partners with Lowes. Not to be used for alternative clients/purposes.
Step 5: Add Decorative Trim
Mina Starsiak of Good Bones partners with Lowes. Not to be used for alternative clients/purposes.
Step 6: Seal Gaps
Mina Starsiak of Good Bones partners with Lowes. Not to be used for alternative clients/purposes.
Step 7: Prep and Paint
Sand rough edges until smooth. Prime and then paint with an exterior-grade paint.
How to cover a post in a hole?
First i made a small mark around each side of the post for 20 inches , which is required where i live. Then i set the new post back into the old hole , adding a little dirt, then a bit of water and all the while tamping the dirt around the post as i went. I continued this process over and over to cover a few inches at a time to make sure the post was well seated into the hole. Make sure to keep a level handy and check that the post remains level throughout the installation process.
How many feet of 4x4 material do I need for a post?
For this Project you will need 1 = 8ft 4x4 material of your choice, for my post i chose cedar but you can commonly find treated pine 4x4 material at any big home center store.
How many screws do I need to install a mailbox?
The installation of the new mailbox is overwhelmingly simple. I used 8 stainless steel screws to attach the box to the platform on top of the post. This process may vary depending on the mailbox you choose for your project.
Can you use urethane on boat posts?
If you are using an untreated material (as i did) You will need to apply some sort of water resistant finish to the post itself. I used a Spar Urethane, which has great water resistant properties and meant for use in the marine field for coating boats. This finish will give the wood several more years of durability with the abuse that any piece will take in being outdoors. Water and UV rays reek havoc on wood so anything that can give some protection will help your new project to last much longer.
Can you put a mailbox post in concrete?
With my post it was simply inset into a hole, but if you have a mailbox that has been set into concrete, you will have to dig out the concrete surrounding the base of of the post. If it is simply placed into the hole, you will need to merely wiggle the post back and forth and side to side until it is loose enough to lift from the hole.
How to trim a column?
To trim the top of the column, measure the width of the sides of the columns. They should all be 6 1/4″ wide but I always measure just to be sure. Cut four 1x4s to the correct width – you want the edges to be mitered at 45º, so the inside of the mitered edges should match the width of the column box. Attach the 1x4s to the column box using a nail gun and finishing nails.
How to cut 1x6 poles?
To determine how long to cut the 1x6s, measure the height of your poles and then take 1/4″-1/2″ off that measurement. You want to make sure you’re not wedging them into place and any gap at the top will be covered later by the trim. Cut four 1x6s to the length you measured, then use the pocket hole jig to drill four holes in two of the 1x6s as shown below.
How many inches are squared up porch posts?
Once the porch posts were squared up, they measured approximately 6×6 inches.
What to spray on 2x3 posts?
Spray on wood preservative to the bottom of the 2×3’s, which serve as the interior framing to the post (or you could use pressure-treated wood).
Can you move siding up to the top of a porch?
After the bottom portion is done, you can move up to the top. Repeat the same steps of adding the siding to all sides of the porch posts & trimming it out on the corners and top/bottom.
Can you use pressure treated 2x3s on porch posts?
If you are using pressure treated 2x3s for the interior framing of the porch posts, you don’t need to do this. But we weren’t so we applied some spray wood preservative to the bottom of the wood that MAY come in contact with moisture. Warning, this stuff is pretty strong smelling so wear and mask and be prepared to let it sit for a bit before working with it. It is great though because it essentially pressure treats the portion of the wood that you spray it on. We definitely keep this stuff locked away in our locking storage cabinets in the garage to protect the kiddos.
Do porch posts need to be pressure treated?
As I explained in the video & above, all of the wood we added to the porch posts is lifted at least 1/4″ off of the ground, so it does not come in contact with the ground. If these porch posts were going to be making contact with ground, the wood would definitely need to be pressure treated.
Prepare for Your Mailbox Column Project
Use a semirigid backing material, such as non-expandable spray foam, as a form for the concrete grouting.
Install Your Column
Wall block sizes vary by style and market. Use the quantities of block and retaining wall pins in the material list as guides. Also, when purchasing wall block, remember that some block has an interlocking lip on the bottom for use in retaining walls, not stacked block projects.
