How do you load a Ryobi trimmer spool? Turn off the Ryobi trimmer. Hold the spool of line in one hand and rotate the bump knob counterclockwise. Remove the knob. Let the trimmer come to a complete stop. Locate the two opposite tabs on the sides of the spool retainer.
Full Answer
How to install a trimmer line on a Ryobi?
How to Install a Trimmer Line on a Ryobi
- Remove the spark plug wire from the spark plug to avoid accidental starts. ...
- Measure a 9-foot length of trimmer line and cut it from the spool. Repeat the process to create a second 9-foot length for installation in the string trimmer.
- Locate the hole in the top part of the spool and insert one length of trimmer line into it. ...
How to tune up a Ryobi Trimmer?
How to Adjust a Ryobi Trimmer Carburetor
- Locate the idle-adjustment screw on the Ryobi trimmer. On the four-cycle Ryobi, the idle adjustment screw is directly below the primer bulb.
- Start the Ryobi engine, and hold the trigger to allow the engine to stay at a high throttle speed for one minute.
- Release the trigger, and allow the engine to idle. ...
- Start the engine again, and test the idle. ...
How to replace string on Ryobi Trimmer?
Reel Easy String Head
- Stop the engine of a Ryobi string trimmer that has a Reel Easy string head. ...
- Cut a 25-foot-long piece of 0.095-inch-diameter monofilament trimmer line from a roll, using a utility knife or scissors for cutting.
- Rotate the knob on top of the head until the arrow on the knob lines up with the arrows on the head. ...
How to replace the pull cord for a Ryobi Trimmer?
Starter Rope Replacement for a Poulan Weed Trimmer
- Work Area, Tools and Safety. Place the trimmer on a flat work area, such as a workbench. ...
- Separating the Housings. Separate the starter recoil housing from the engine housing cover on the Poulan trimmer. ...
- Tensioning and Replacement. ...
- Recoiling and Reconnections
How do you load a Ryobi strimmer spool?
0:000:31Load The RYOBI REEL-EASY SPEED WINDER Bump Feed Trimmer HeadYouTubeStart of suggested clipEnd of suggested clipPlace crank attachment on grouped section of the trimmer head and rotate clockwise to reload lineMorePlace crank attachment on grouped section of the trimmer head and rotate clockwise to reload line until six inches remain on each.
How do I put trimmer line in a Ryobi?
2:083:27How to change the trimmer line on a Ryobi 18 volt cordless string trimmerYouTubeStart of suggested clipEnd of suggested clipYou just get the head. Put it back in make sure the caps in place look at these two little tabs makeMoreYou just get the head. Put it back in make sure the caps in place look at these two little tabs make sure they're actually holding and you got it all the way.
How do I put line on my 18v Ryobi trimmer?
0:563:56How to ReString, ReSpool or ReLine Ryobi weed trimmer ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut this is what I'm using 0.09 it's pretty thick trimmer line and it's actually looks like that youMoreBut this is what I'm using 0.09 it's pretty thick trimmer line and it's actually looks like that you get out about I know three. Feet. No you got to make sure the arrows point to the holes. Right it
How do you rewind a string trimmer spool Ryobi?
1:232:03Ryobi String Trimmer Spool Replacement 530670001 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow align the crank handle on the bump knob and rotate the handle clockwise while holding theMoreNow align the crank handle on the bump knob and rotate the handle clockwise while holding the trimmer head to wind the line around the spool. Keep winding until the line is within the guard assembly.
How do you fill a trimmer line?
0:262:19Replacing a Weed Eater String (String Trimmer Line) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThread each end of the line through the eyelets on the trimmer head as you connect the spool andMoreThread each end of the line through the eyelets on the trimmer head as you connect the spool and bump knob wind the bump knob based on the arrows shown on the reel. Apply pressure to wind it evenly.
How do you put trimmer line on?
0:121:28String Trimmer Line Installation Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine and a traditional bump head requires you to disassemble the cutting head but first you'll needMoreLine and a traditional bump head requires you to disassemble the cutting head but first you'll need to cut about ten feet of line to install. You can either use twin strand split line or cut two
Why does my trimmer line keep coming out?
If this cap is broken or worn out over time, it can malfunction, causing too much line to feed out when you bump it. Depending on its damage, it could be getting hung up as it tries to return, allowing the line to continuously advance. To replace it, simply remove and replace the bump cap with a new one.
Wear Safety Equipment
Dress properly and wear safety equipment to protect yourself from any kind of incident.
Types of Ryobi String Trimmer
There are two main kinds of string trimmers: gas-powered or electric trimmers. Gas string trimmers are cordless, powerful, have two-cycle engines, and need a mixture of gas and oil to work.
Step by step guide to load a Ryobi String Trimmer
After you use your Trimmer for a season of use, it will probably need some replacements. This two-line trimmer typically uses a 0.080-inch diameter monofilament trimmer replacement line.
Use of Ryobi String Trimmer
String trimmers are designed for chopping grass that’s not easily reached by a mower, like under bushes or up against walls. Always take care when trimming around small plants and flowers as they will be easily damaged.
Last Thoughts
Ryobi string trimmer is very useful to trim the grass of lawns in your home. Make sure to follow safety precautions before using a string trimmer.
How to remove spool from a spool trimmer?
On gasoline-powered models, remove the spool by rotating the spool retainer counterclockwise for some models and clockwise for others and then lifting the spool off the head. On cordless models, remove a cap with your fingers by holding in the tabs that hold it to the head. After removing the cap, lift the spool off the trimmer head.
How to get a reel out of a spool?
Pull the lines tight, and then turn the inner reel counterclockwise to wind the strings around the spool hub. If the reel gets stuck, pull the strings sharply away from the spool to release it. Stop turning when 4 inches of line remain outside the holes in the outer spool.
How to cut string on a trimmer?
Unplug the trimmer and turn it over so you have access to the string head. Cut two lengths of new string from a roll with a pair of scissors. If your model uses 0.80-inch line, cut 10-foot lengths; if it uses 0.60-inch line, cut 15-foot lengths.
How to stop winding a rim?
Stop winding when you have about 6 inches left on the end and hook the end onto one of the slots on the rim. Wind the second string in the same way. Feed the ends of the string through the eyelets of the string head for gasoline models or the string cap for cordless ones and replace the spool on the shaft.
How to wind a syringe?
Feed the end of one string into the locking hole in the center of the hub and wind the string around one half of the hub, being careful not to cross or overlap the string. Stop winding when you have about 6 inches left on the end and hook the end onto one of the slots on the rim. Wind the second string in the same way.
How to release strings from spool?
Pull the strings sharply to release them from the notches in the spool.
Can string be too big for a machine?
Using string with a diameter too large for your machine can make it work too hard and may burn out the engine.
What is Ryobi string trimmer?
Ryobi manufactures a number of gasoline-powered string trimmers, as well as a battery-powered model that is part of its One+ line of tools that operate on a common lithium-ion battery-pack. The string heads for the gasoline- and battery-powered models aren't the same. The most important difference is that the latter takes only a single 0.065-inch string while the former takes two strings that can be from 0.080 to 0.095 inches in diameter. The procedures for winding the heads are similar and shouldn't delay your trimming job for longer than about 10 minutes.
How to clean a spool on a spool?
Remove the spool, ensuring that the spring remains attached to it. Pull off any old string and clean the spool and the inside of the head with a rag.
How to turn a string head?
Hold the string head with one hand while you unscrew the spool retainer with the other. You may have to turn the head clockwise or counterclockwise; some heads have reverse threads while others don't.
How to make a spool of arrows?
Cut a single 9-foot length of 0.065-inch microfilament string from a roll. Feed one end into the hole in the center of the spool and wind the string in the direction of the arrow. Stop winding when 6 inches of string are left on the end.
How to replace a spool retainer?
Replace the spool retainer by aligning the tabs and pushing down until they lock. In order to avoid overfilling the spool, ensure that there is 1/4 inch of space between the wound string and the outside edge of the spool. Avoid using string that is too wide for your trimmer.
How to wind a string in a spool?
Insert the end of one of the lengths of string into the upper anchor hole in the hub of the spool and wind the string in the direction of the arrow on the base of the spool. Keep the string confined to the upper section of the spool and stop winding when about 6 inches of string remains.
How much space between wound string and spool?
In order to avoid overfilling the spool, ensure that there is 1/4 inch of space between the wound string and the outside edge of the spool. Avoid using string that is too wide for your trimmer. It won't advance properly, and you could overwork the trimmer engine and burn it out.