How do you light the pilot on a Bradford White defender? VIDEO. Click to see full answer. Regarding this, how do I light the pilot on my water heater? Turn the gas regulator valve's knob to “Pilot,” press down on it and hold it down. This starts the flow of gas to the pilot burner.
Where is the pilot light on Bradford White water heater?
1:224:22How to light Bradford White Hot Water Heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou turn it to the pilot mode it's going to say pilot rate on the bottom now the light instructionsMoreYou turn it to the pilot mode it's going to say pilot rate on the bottom now the light instructions is right on the actual gas control itself and then also on the sticker on the heater.
How do I turn the pilot light back on?
How Can I Restart My Pilot Light?Step 1: Turn off your furnace. ... Step 2: Locate your gas valve. ... Step 3: Hold down the red button. ... Step 4: Light the pilot light. ... Step 5: Let go of the button. ... Step 6: Turn your gas back on. ... Step 7: Turn your furnace back on.
How do I reset my Bradford White eco defender water heater?
0:032:19How to reset your Bradford White Defender Water Heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd hold it hold it hold. It. I as you can see there that status light on the right see how it's notMoreAnd hold it hold it hold. It. I as you can see there that status light on the right see how it's not blinking. Okay i had to hold the camera with my chin.
How do I reset my Bradford water heater?
Resetting your Bradford White Water Heater is relatively easy once you realize that there is no reset button. Make sure that the pilot is turned on, switch the dial to “very hot” for 10 seconds, to “hot” for 10 seconds and to “pilot” for 10 seconds. This will reset your water heater.
Where is the furnace pilot light?
Near the bottom of your furnace is a switch that normally says "Pilot," "On" and "Off." Find this switch and turn it to the "Off" position. Wait at least five minutes. This is important because it gives the gas time to dissipate, which is necessary to avoid possibly starting a fire.
How do I light the pilot on my water heater?
How to Light a Water Heater Pilot LightOpen the door/cover over the pilot light access. ... Use a flashlight or a headlamp to find the burner inside. ... Turn the gas knob to “Pilot,” press and hold it down. ... While still holding the gas down, light that pilot.More items...•
How do you turn on a pilot?
Turn the valve to “Pilot.” Near the valve, you'll see a small button labeled “Reset.” Press this button while applying your lit match or butane fireplace lighter to the pilot light valve. Hold the flame steady until the pilot ignites, then release the button.
How do I reset my Bradford White gas valve?
To reset, depress button on resettable thermal switch located on inner door. Pilot goes out periodically (after heating cycles, once a day, once a week etc.)
How do I restart my water heater?
0:202:56How to reset gas water tank pilot light - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you were to come home and have lukewarm or cold water in your hot water heater it's. ProbablyMoreIf you were to come home and have lukewarm or cold water in your hot water heater it's. Probably because the pilot light went out during the day. So you want to set this to off for a few minutes let
Why is my Bradford white water heater not lighting?
Common solutions for: Bradford White Water heater not lighting. Some water heaters use an igniter to ignite the gas. If the igniter fails, the burner will not light. To determine if the igniter is defective, first make sure the igniter is getting voltage.
What happens if a water heater pilot is not lit?
The pilot ignites the water heater’s gas burner. If the pilot does not light, the water heater will not heat. Sometimes, carbon deposits can build up on the pilot and eventually create a restriction. If the pilot is restricted, try removing it and clearing it with a stiff brush and/or compressed air. If the pilot cannot be cleaned, replace it.
What is the purpose of a spark electrode on a water heater?
Some water heaters use a spark electrode to light the pilot flame. The spark electrode sends intermittent high-voltage sparks to light the pilot. If the spark electrode won’t produce sparks, it is likely defective. If the spark electrode is defective, replace it.
