1. Hold down the red button on the gas safety valve to release gas. 2. Light pilot by pushing the red ignitor button. You may need to press it more than once. Continue pressing the igniter button until the pilot stays lit.
How to light a pilot light on a gas furnace?
Here we discuss how to light a pilot light on a gas furnace. If you have an electric furnace, then you are in the wrong place (and your furnace doesn’t even have a pilot). Locate the switch or knob that displays three settings (On, Pilot, Off). Set the knob to off, then wait a couple of minutes in order to allow the gas to dissipate.
How do you light the pilot on a propane tank?
Depress the button or knob for about 30 seconds. This maintains gas flow to the pilot until the thermocouple gets hot enough to open the main gas valve. Once the pilot stays lit, slowly release the button or knob and then turn the gas cock or knob from the "pilot" position to the "on" position.
How do you light a gas pilot without a red button?
If you have a pilot with a red reset button, turn the gas valve from "off" to "pilot." If you have a pilot without a red button, turn the control knob from "off" to "pilot." Light the Standing Pilot Place the lit match or ignited lighter tip at the pilot while depressing and holding the reset button or depressing the knob, as appropriate.
How do you reset the pilot light on a Kenmore gas furnace?
Relight the Pilot Light Next, locate the reset button, which should be near the on/off switch. Press and hold the button and place the tip of a lit match or lighter near the pilot light opening. This should reignite your furnace’s pilot light. Release the button once the pilot flame is lit and burning steadily. Getting Warmer …
Does American Standard furnace have a pilot light?
If you're a lucky owner of an American Standard furnace with a standing pilot, then you might have to reignite the light at one point. Follow the small copper tubes that are attached to the control valve to locate the pilot light. Turn off the gas control. Turn the knob to the 'pilot' position.
How do I relight the pilot on my furnace?
How Can I Restart My Pilot Light?Step 1: Turn off your furnace. ... Step 2: Locate your gas valve. ... Step 3: Hold down the red button. ... Step 4: Light the pilot light. ... Step 5: Let go of the button. ... Step 6: Turn your gas back on. ... Step 7: Turn your furnace back on.
How do I reset my American Standard furnace?
1:101:42american standard furnace troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipIssues switch the power on and off twice within 30 seconds. This is a standard reset procedure forMoreIssues switch the power on and off twice within 30 seconds. This is a standard reset procedure for american standard furnaces.
Where is my furnace pilot light located?
Near the bottom of your furnace is a switch that normally says "Pilot," "On" and "Off." Find this switch and turn it to the "Off" position. Wait at least five minutes. This is important because it gives the gas time to dissipate, which is necessary to avoid possibly starting a fire.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
Is it safe to relight my pilot light?
Safety First You should always proceed with care when relighting a pilot light, since the gas used to power your hot water heater is flammable and potentially dangerous. If at any time you smell gas, you should shut off the gas valve right away, open windows, and avoid turning on any lights.
What does a blinking red light mean on an American standard furnace?
0:441:38American Standard Blinking Red Light - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf it is blinking quickly it means that your American Standard furnace is heating up and gettingMoreIf it is blinking quickly it means that your American Standard furnace is heating up and getting ready to warm your house.
How do I reset my American standard?
Locate the switch for your thermostat in the breaker box. Flip the switch to the OFF position for 20-30 seconds. Return the switch to the ON position. The reboot process will take several minutes to complete.
How do you troubleshoot an American Standard furnace?
If you start to experience problems with your American Standard furnace, here are some troubleshooting steps that can help: Turn off the furnace or the breaker box. Check the filter to make sure it's clean, and replace it if necessary. Inspect the furnace and vents for dirt and debris, and vacuum them if necessary.
Where is the reset button on a furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Steps to Relight a Furnace Pilot Light
Locate the switch or knob that displays three settings (On, Pilot, Off).
Find Replacement Furnace Parts
Now that you know to light a pilot, you might need new parts if your furnace still isn't working. You can save on all kinds of heating/cooling parts like furnace ignitors, blowers and motors, blower wheels, and more.
Where is the pilot light on a furnace?
If you’ve read the unit’s instructions, you probably already know where the pilot light is located. Otherwise, check near the bottom of the furna ce for a switch or knob, which should have three indicators: pilot, on and off.
Why does my furnace have a pilot light?
If you have an older furnace or a gas heating system, it probably has a pilot light. That’s the small blue flame that lights the natural gas coming from the unit’s main burner. This pilot light can go out for a variety of reasons, literally leaving you in the cold.
What to do if pilot light isn't lit?
What to Do If Your Furnace Pilot Light Still Isn’t Lit. If your furnace pilot light isn’t lit after following the five steps above, try again. If it doesn’t light after a second try, or it doesn’t stay lit after releasing the reset button, your unit may require additional maintenance. It may be time to repair or replace your furnace, ...
What do you need to relight a pilot light?
To relight your pilot light, you’ll typically need a flashlight and a long-reach lighter or long-handled match. If you don’t have an appropriate lighter or match, a tightly rolled piece of paper may be used instead.
How long to wait after turning off a pilot?
After switching the pilot off, you should always wait at least five minutes prior to restarting to avoid starting a fire or causing injury to yourself or others. Then, switch it to “pilot.”. 5. Relight the Pilot Light. Next, locate the reset button, which should be near the on/off switch.
What color should the pilot light be on a gas furnace?
Amazon. If the pilot lights but the flame is weak and yellow, it will not get hot enough to heat the thermocouple to its set point and allow the gas valve to open. If your furnace runs on natural gas, the flame should be a bright blue with the tip of the flame having just a tinge of yellow.
What to use to light a pilot?
If possible, try and use a long fireplace match when you light it. If you don't have a fireplace match, then a butane barbecue grill lighter works well, too. If you don't have that, fasten a match to the end of a stick as you light the pilot.
What is the purpose of a standing pilot?
When the thermostat signals for gas to be delivered from the gas valve to the burner, the standing pilot ignites the gas flowing to the burners to heat the air in the combustion chamber. When this little flame fails to operate properly or goes out, ...
What happens when the pilot goes out of the gas valve?
If the pilot goes out, then the thermocouple gets cold and doesn't produce an electric signal to open the gas valve's solenoid, so the gas valve shuts off the gas supply to the pilot and burners.
How to turn off gas in furnace?
Make sure the thermostat is set to the "heat" mode. Go to the furnace, and find the pilot valve, a box-shaped device into which the main gas line will run.
Why is my pilot tube turning yellow?
Turn the screw as needed to adjust the flame throw. Yellow flame: A yellow flame is caused by lack of air and incomplete combustion. It can be caused by a dirty pilot tube tip, which can be corrected by cleaning it. Split flame: This is usually caused by dirt in the pilot tube.
How far should a thermocouple hit the flame?
The flame should be strong enough to hit the thermocouple tip about 1/2-inch from the tip end. If the flame is weak or shaky looking, check to see that a breeze or draft is not blowing on it. Adjusting the flame: There is usually a small screw on the pilot valve body that will adjust the flame.
Reasons Why Your American Standard Furnace Is Blowing Cold Air
What it is: the blower motor is the part of your furnace that pushes the heated air through the vents in your house.
How to Relight the Pilot Light ?
If you’re a lucky owner of an American Standard furnace with a standing pilot, then you might have to reignite the light at one point.
