Full Answer
How do you finish shiplap tongue and groove walls?
You can either apply finish to the raw wood on each chamfer before nailing up each board or touch up the entire shiplap ceiling after it's finished. Always plan your work so the tongues point toward the direction of installation. One of the cool things about tongue and groove walls is that you can use a technique called "blind-nailing."
How do you attach tongue and groove to drywall?
If you're installing tongue and groove boards over drywall (or plaster especially), it's a good idea to install 1x2 battens and fasten them directly to the framing with 2-1/2-in. screws. They'll give you a much more solid nailing surface.
How do you install shiplap over drywall?
If not, tape and mud the drywall seams before installing the shiplap. Taping and mudding offer extra protection against insects, pests, odors, or drafts that might seep through the wall. Once you’ve found and marked the studs, begin sticking the pieces of shiplap in place using a heavy-duty adhesive.
What tools do I need to install shiplap or tongue and groove?
A finish nailer or brad nailer is the easiest and most efficient tool to use when installing your new shiplap or tongue and groove. They can be purchased/rented relatively cheaply from your local hardware store, they’re lightweight, and are simple enough that a 12 year old can use them!
How do you install shiplap over existing drywall?
Once you've found and marked the studs, begin sticking the pieces of shiplap in place using a heavy-duty adhesive. This gives you a tougher, more durable hold for your shiplap walls over drywall, and it also allows you to get a sense of board placement before you start nailing everything to the studs permanently.
Can you add shiplap over drywall?
Does Shiplap Go Over Drywall? You don't have to put your shiplap over drywall if there isn't existing drywall already in place. However, if you are simply remodeling a room, you can certainly put shiplap over existing drywall.
Should you remove drywall before installing shiplap?
If you already have drywall installed, go ahead and add shiplap. If you don't, install it directly to studs. This will save you time, money, and hassle. When adding shiplap directly to studs, you will not have drywall added unless you want it.
Do you nail the tongue or groove of shiplap?
We always recommend face nailing shiplap and tongue and groove when installing it on your walls, ceiling, and as exterior siding. Face nailing means that you shoot your nail at a 90 degree angle to the board through the flat (or face) of the board.
Should you glue shiplap to drywall?
Shiplap planks can be fastened to walls either vertically or horizontally. Simply nail through the drywall directly into wall studs. You can use construction adhesive when installing on ceilings or over other surfaces, as long as they're in good condition.
How do you install wood planks over drywall?
3:207:55How to Install a Decorative Wood Wall For Less than $200 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd once the boards are cut to length you can put them up against the wall line them up with theMoreAnd once the boards are cut to length you can put them up against the wall line them up with the line that you drew to make that first row level. And then take out your nail gun.
Can I put tongue-and-groove over drywall?
If you're looking to reboot the atmosphere in a living room or bedroom by covering the existing drywall with tongue-and-groove boards, the good news is that there are no codes prohibiting it. In fact, the fire-resistance of drywall balances the propensity of wood to burn and makes the room safer than wood alone.
Does shiplap need to be nailed to studs?
Always use 2 nails or screws to attach each board to the stud, and make sure that they penetrate the studs. If you're staggering your shiplap, be aware that the spot where the staggered boards butt together will not be the same from level to level.
Does shiplap have to end on stud?
Using your nail gun, shoot a nail into each stud about 1″ up from the bottom of the board. You can nail at every stud if you choose, but with shiplap, every other stud will keep the wood very secure. Work your way all the way across the bottom of the wall.
Where do you nail tongue and groove shiplap?
Avoid visible nail holesInstall planks with the tongue up.Nail at an angle directly through the tongue and into your studs. You don't need to nail through the face of the planks anywhere but on the bottom row and near the ceiling.Start with the bottom row first and work your way up.
What kind of nails do you use for tongue and groove?
We recommend using 16- or 18-gauge finish or brad nails. 1-½” to 2” in length should be sufficient. Both gauges are strong enough to hold the lumber securely, but small enough as to not leave a large hole on the face of the board. Go ahead and buy the bulk pack: you're going to need it!
How do you fasten a tongue and groove board?
Drive the nails through the shoulder of the tongues into the framing at about a 45-degree angle. The next grooved edge will hide the nail holes. A 15- or 16-gauge brad nailer with 2-in. nails is the best choice for fastening, although an 18-gauge nailer will do the job, too.
What is tongue and groove board?
Installing tongue-and-groove (aka T&G) boards is a fast, inexpensive way to panel any ceiling or wall. You can install T&G over bare framing, drywall or plaster, so it's a great cover-up for an ugly ceiling.
Can you mark electrical cutouts on tongue and groove?
It's really tricky to accurately mark cutouts for electrical boxes and other ceiling openings on tongue and groove. The secret is to scribe and/or mark as much as possible in place on the shiplap ceiling rather than to try to measure everything perfectly.
Can you put tongue and groove together?
(2) You have to seat the tongues and grooves together, and they don't always want to marry. (3) Tongue and groove isn't always flat, so you have to force the boards together to get them seated.
Can you fit grooves in tongue and seat?
Break off the groove flanges. On any installation, you'll have times when you can't fit the groove in the previous tongue and seat the board. In fact, it's almost always the case with the very last board. But it can also happen at shiplap ceiling protrusions or even at projecting inside corners.
Can shiplap be lifted into place?
But it can also happen at shiplap ceiling protrusions or even at projecting inside corners. The only option is to eliminate the back of the groove so you can lift the board directly into place without locking the joint together. The easiest way to do this is to break off the flange with a few hammer raps.
Can tongue and groove boards be unfinished?
Tongue-and-groove boards are notorious for shrinking and expanding with changes in temperature and humidity. Unfinished tongue and groove boards installed in humid summer conditions can be an ugly mess during the dryness of winter. As the wood dries and shrinks, unfinished stripes will appear where the tongues withdraw from the grooves. But if you apply finish before installation, the tongues will be completely finished—no unfinished stripes to appear later! You could also opt for paint to finish your boards for a white shiplap ceiling look.
How deep should furring strips be in drywall?
The fasteners holding the boards must be long enough to penetrate the wood behind it, but if you use furring strips, they shouldn't penetrate more than 1/2 inch into the drywall, or they could pierce an electrical wire or a pipe.
Why leave drywall in place?
Leaving the drywall in place means that you can't modify the framing to provide nailing support for the boards. If you're installing them horizontally, that isn't an issue, because the studs run perpendicular to the boards and are easy to locate with a stud finder.
Can you cover drywall with tongue and groove boards?
If you're looking to reboot the atmosphere in a living room or bedroom by covering the existing drywall with tongue-and-groove boards, the good news is that there are no codes prohibiting it. In fact, the fire-resistance of drywall balances the propensity of wood to burn and makes the room safer than wood alone.
Can you install furring strips vertically?
In lieu of the blocking that would be in the wall to hold them, you may have to screw horizontal furring strips or 1/4-inch plywood to the wall, fastened to the studs.
