How to Install a Sterling Shower Base
- Remove the Existing Shower. Remove the existing shower walls, then remove the drywall off the sides of the walls by cutting it into sections with a drywall saw ...
- Install the Shower Drain in the Base. Install the shower base drain assembly by inserting the top half of the drain into the drain hole so the threaded ...
- Level the Shower Base. Cut a hole in the subfloor for the drain and dry fit the Sterling shower base into the installation area.
- Lay a Mortar Bed (Optional) Remove the shower base and install a mortar bed, if necessary. ...
- Nail the Base to the Wall Studs. Remove the drain dam and place the shower base into the installation area. ...
- Install Cement Board on the Walls. Install the cement board on the framing walls with drywall screws and a power screwdriver, overlapping the shower base lip.
Do you need glue on installing a shower base?
When replacing a shower pan, some shower pan manufacturers call for the shower pan to sit directly in an adhesive or into small mounds of mortar. If adhesive is called for, spread it within the area where the shower pan will sit. If mounds of mortar are called for, mark the locations on the subfloor per the manufacturer’s instructions.
How to install a sterling shower base?
Things You Will Need
- Level
- Latex modified thinset mortar
- Notched trowel, 1/4-inch
- Drill and paddle
- Drill screw attachments
- Bucket
- Wood screws
- Pipe wrench
How to install a preformed shower base?
Prepare the Subfloor
- The entire bottom of the shower pan needs to sit on a flat, level surface. ...
- If the subfloor is completely flat and level, proceed to step 3.
- If the subfloor is not flat and level, apply a self-leveling compound following the manufacturer’s instructions. ...
- Run the self-leveling compound up to the line you drew in step 1. ...
How do you install a shower in the basement?
Trench the Floor
- Start breaking up the basement floor at the main line with a sledgehammer. Note: Breaking through at the tie-in point may take a few dozen whacks.
- Pick out the larger chunks of concrete as you go.
- Toss the dirt in a pile separate from the larger chunks of concrete. Note: You don't want big chunks in the soil you'll use for backfill later.
What do you put under shower base?
Mortar is recommended to use under all shower pans. Mortar reduces the risk of your pan slipping or cracking from an uneven surface.
How do you secure a shower base to the floor?
1:463:22How to Install a Shower Pan | The Home Depot with @This Old HouseYouTubeStart of suggested clipEnd of suggested clipWe added temporary strapping to the studs to hold the pan in place some manufacturers call for theMoreWe added temporary strapping to the studs to hold the pan in place some manufacturers call for the flange of the shower pan to be screwed directly to the studs.
Do you need mortar under shower base?
0:094:09Using Mortar Under Fiberglass Shower or Tub - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the reason you want to do that is because if you get too much flux in the bottom particularly onMoreAnd the reason you want to do that is because if you get too much flux in the bottom particularly on cheap tubs. Or really large surface area tubs you can get damaged and leakage.
Do you screw a shower base to the wall?
Unlike concrete shower pans which bond to the floor and are held in place by cement, shower bases are held in place with screws. Connecting the shower base to the wall studs is part of the installation process to hold the pan in place.
What do you stick a shower tray down with?
Using either tile adhesive, silicone or a weak cement mix (5 parts sand/ 1 part cement) apply sufficient to board to cover entire underside of tray. Apply a minimum of 5mm thickness to lowest point of tray. More may be required in places to ensure tray is level.
What type of mortar do you use to set a shower base?
The best type of mortar to use underneath a shower base is a mixture of Portland cement and sand. This mortar will both support the weight of the shower and provide a barrier that helps prevent water damage to the floor underneath.
Do you put cement board under a shower pan?
The wallboard must be installed 1/8 inch above the shower pan. If the shower pan is not in place, the wallboard height must be guessed, which can lead to inaccuracies and an expansion gap that is too large or too small.
Can you use expanding foam under shower base?
Only a minimal-expanding foam should be used under a shower pan. The reason for this is that when foam expands it exerts pressure against opposing forces. And so, you could end up with bowing or even cracking of your shower pan.
What is the difference between a shower pan and a shower base?
What Do They Do? While a shower pan and a shower base both channel water into the drain, there's one key difference: “Shower pan” is the actual shower floor that you step on, whereas “shower base” refers to the structure underneath the shower itself.
Can you install a shower kit over drywall?
The short answer to the question is, “It's not recommended.” However, this answer only really only suffices if you're converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.
Do you install shower pan before drywall?
For tile or shower panels, drywall goes in first. Installing a shower pan includes many steps, such as cementing the floor to create a sturdy base and installing the shower walls.
Can you put a shower base over tiles?
In most cases, you cannot tile on the floor of standard fiberglass/acrylic shower pans. Slight flexing will quickly crack the grout and even the tiles. However, some specialty shower pans such as those made by Tile-Redi are designed for over-tiling.
What to use to seal a water channel?
Apply silicone sealant between the module and drywall or finished wall material.
How to prevent water from passing behind walls?
Ensure faucets and accessories are sealed with 100% silicone sealant to prevent water from passing behind the walls. Clean the back side of the walls, taking care to ensure the water channel does not have any debris in it (Fig. 12). Cellulous or other soft insulation may drop down into the water channel.
Can you put a bathtub in cement?
If the sub-floor is uneven or not level, it is recommended the bathtub be installed in a bed of mortar cement. The fabric pad is not required for mortar cement installations. (Do not use Structo-Lite, Gypsum Cement, drywall compound or plaster). Make sure the bathtub apron brace is engaged.
