How do you install a Lyons shower surround?
- 01 of 06. Introduction.
- Prepare the Walls. Direct-to-stud surrounds are great for complete bathroom remodels where all walls are usually removed down to the studs.
- Start With the Back Wall Panel.
- Install the First Side Wall Panel.
- Prepare the Last Side Wall Panel.
- Install the Last Surround Panel.
How do you install a shower surround?
To ensure that the surround properly bonds to the wall, clean the walls and apply a primer to the backerboard. Let the walls dry. If you're installing a shower surround, install the shower pan first. Shower pans are often included in the shower surround kit. Follow the manufacturer's directions for installation.
What are the parts of a shower surround?
These tub and shower surrounds have top, bottom, and side flanges that are screwed or nailed to the wall studs. Some surround kits are designed for a specific shower base or tub, while others can be retrofit to any existing tub of appropriate size.
How do you install a 3-piece bathroom surround?
In order to properly install a 3-piece surround, you need to make sure the bathroom is clean and prepared. The surround sits directly on top of the tub and against the bathroom walls. An unobstructed surface is paramount to the success of the project.
How do you remove a bathroom shower surround?
The surround sits directly on top of the tub and against the bathroom walls. An unobstructed surface is paramount to the success of the project. Use the wrench and screwdriver to begin removing all of the fixtures that are installed in the shower and tub. You will need to lift up the metal plates and either twist them off or unscrew them.
How do you install a shower surround?
0:332:28How to Install a Shower Surround - Menards - YouTubeYouTubeStart of suggested clipEnd of suggested clipInstall the plastic attachment clips at all of the remaining stud locations. With the unit levelMoreInstall the plastic attachment clips at all of the remaining stud locations. With the unit level shim under the support feet as needed and secure the clips. Now you will install the wall set install.
How do you install a Lyons contour shower door?
0:052:38Tub and Shower Door Installation - Menards - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore you begin make sure the door and panel fit within the tub enclosure measure the height andMoreBefore you begin make sure the door and panel fit within the tub enclosure measure the height and width of the tub enclosure. And compare them with those of the door and panel you wish to install.
Do you put drywall behind a shower surround?
0:111:28Do You Drywall Behind Tub & Shower Enclosures? - YouTubeYouTubeStart of suggested clipEnd of suggested clipI do this behind the enclosure all the way up to get myself a nice level wall. And it works perfectMoreI do this behind the enclosure all the way up to get myself a nice level wall. And it works perfect and I get no water penetration ever in my bathtubs.
What should you put behind a shower surround?
Use an appropriate waterproof or moisture-resistant backing material behind grouted tile or stone or segmented plastic or fiberglass tub and shower surrounds. Appropriate materials include cement board which has a cementitious core and glass mats on both sides to strengthen the board.
How do you install a framed glass shower enclosure?
1:195:40DIY Framed Shower Door Installation - Basco Deluxe 6150 & 7150 How ToYouTubeStart of suggested clipEnd of suggested clipIf reinforcement is built into the wall of the unit drill six 1/8 inch holes to install mountingMoreIf reinforcement is built into the wall of the unit drill six 1/8 inch holes to install mounting screws directly into the reinforcement. Next run a heavy bead of silicone caulk.
How do you install a shower door on a fiberglass shower?
Installing a shower door over a fiberglass shower is the easiest type of shower door to install because there is no need for additional anchors or masonry bits like there is for concrete or tile installation. With a fiberglass shower all you have to do is screw in the shower door and seal it in place.
What is the best material to use behind shower walls?
acrylicWe recommend acrylic as the best shower wall material. Acrylic is the best system to use for shower walls because it is the safest, least high maintenance, and easy to install, meaning your shower could be done in as little as one day.
How do you fill the gap between shower surround and drywall?
1:513:53Drywall gaps around tub and shower surrounds, How to fix them - YouTubeYouTubeStart of suggested clipEnd of suggested clipEverything needs something to bond to mix up some 20-minute speed set joint compound. And press itMoreEverything needs something to bond to mix up some 20-minute speed set joint compound. And press it into the gap keeping it flush with the drywall.
Should you put plastic behind shower walls?
They are required beneath your shower pan and behind your shower walls. Moisture barriers can be made of polyethylene or a membrane that is rolled directly onto the drywall. No matter what they are made of, without them, your shower is subject to moisture damage.
Do you drywall over shower flange?
0:005:44How to install drywall over a tub or shower flange - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike you and you and hope that's the case of mine. Over here where I've already started the existingMoreLike you and you and hope that's the case of mine. Over here where I've already started the existing sheetrock was probably a half-inch the face of this sheetrock a half-inch in front of the flange.
Can you install shower surround over tile?
Tub surrounds can sometimes be installed over existing tile, but only when conditions are right. The old tile area needs to be smaller than the kit and you'll need to build up the surrounding wall to the level of the tile, usually with 1/4-in. drywall. All things considered, removing the tiles is often a better option.
Do you need put plastic behind cement board shower?
plastic behind cement board with waterproofing is essentially suspenders when you already have a belt. the waterproofing is also a vapor retarder so if the red guard or kerdi product is continuous, lapping corners and all, the plastic will be unnecessary.
How many pieces are needed for a shower surround?
Most tub and shower surrounds designed for remodeling applications come in three or five pieces to make installation in tight spaces easier. The surround kits designed for attachment to studs are usually made ...
What is the final panel of a shower?
The final panel is the one containing the plumbing fixtures; this is usually the front wall of the shower. Before installing this last panel, it will have to be drilled for the tub or shower valve and maybe a tub spout. Take measurements off of the back wall to the center of the valve, and off of the tub or shower base to the center of the valve.
What is an alcove shower enclosure?
An increasingly popular option for the alcove enclosures for bathtubs and showers is a surround kit that uses acrylic or fiberglass panels. This type of kit is cheaper and easier to install than ceramic tile wall enclosures and is remarkably easy to maintain. There are two types of installation for tub/shower surround kits: direct-to-studs ...
Can a direct to stud shower surround be trimmed?
You may void the warranty if it isn’t done according to the manufacturer's specifications. When buying a direct-to-stud surround, make sure that you get the right size for the width of tub or shower you have. This type of surround can't be trimmed to fit in ...
Do you need a pry bar for demolition?
This is demolition work that may require a pry bar and reciprocating saw, depending on what type of wall surface is present . Often, it is best to cut out an area of wall slightly larger than the surround, because this makes it easier to anchor the flanges to the studs.
Can you install drywall after it is installed?
After installation, you can then install drywall so it butts up to the surround over the nailing flanges. When removing drywall, make sure to remove all nails or screws, and check to make sure the studs lie in a flat plane. If necessary, you may need to shim out the studs if they are uneven or bowed.
What is glue up shower?
These glue-up surrounds are the easiest to use for bathrooms with windows, or where the bathtub or shower enclosures are oddly sized.
How to get adhesive off of a wall?
Carefully position the back panel and press it against the wall so the entire panel makes contact with the adhesive. Pull the panel slightly away from the wall for about 30 seconds. This allows the solvents in the adhesive to slightly dissipate and improves adhesion.
Can you trim shower surround panels?
But it is also possible you will need to trim panels to fit, so it's critical that you test-fit the surround panels before you begin the installation.
Can you put adhesive over drywall?
Prepare the Walls. Adhesive surround kits can be installed over just about any flat wall surface in good condition, including tile or drywall. But because the panels are glued, the walls need to be clean so that the adhesive will make good contact. Walls that are damaged will also need to be patched first.
What is a 3 piece shower surround?
The first is that it actually has nothing to do with sound and the second is that it’s not three pieces but typically 4. A 3-piece tub and shower surround is made from durable plastic and covers an existing tub and shower. In many cases the tub and far wall will be one piece and the extra piece will be a corner section.
What is a 3 piece shower?
A 3-piece tub and shower surround is sized larger than is what is needed. This will allow you to fit and trim it to what you really need. Remove it from its box and dry fit the pieces. The tub section goes on first, then the sides. Make sure the precut holes are over the faucet and showerhead area.
