Determine the length of cable needed and the proper route for the throttle cable to follow. Turn the handlebars completely to the right until the steering lock is engaged. Install the accelerator cable (pull cable) onto the throttle housing, running the cable end into the mounting hole farthest from the rider.
How do you hook up a throttle cable?
- The throttle cable housing may need to be adjusted periodically because the cable stretches.
- Fully loosen the jam nuts (1) and (2) and mount the throttle cable housing to the frame.
- Pull the throttle cable housing toward the rear of the kart until you feel resistance.
How to install a throttle cable into carburetor?
Installing the Throttle Cable. Image 2: Remove black piece. 1. Remove the black piece covering the brass fitting at the top of the carburetor. Image 3: Remove two screws from top plate. 2. Remove the two screws holding the top plate on the carburetor. Images 4 & 5: Remove spring and slide assembly. 3.
How to properly adjust throttle cables?
Part 1 of 2: Test drive and determine how much to adjust the throttle
- Marker
- Owner's manual
- Screwdriver
How do you replace a throttle cable?
disconnect the throttle cable from the throttle body. follow the throttle cable around the engine and you will find it goes through the fire wall and connects to the gas pedal. disconnect the cable from the gas pedal and pull out of the cab compartment from engine side.
How do you put a throttle cable back into a carburetor?
1:317:18(2)- CARB THROTTLE CABLE INSTALL EASY (end) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe go down through the top right here. And it hooks in you see the little Seether. You see the lineMoreWe go down through the top right here. And it hooks in you see the little Seether. You see the line it hooks and all these carburetors exactly the same it hooks in a little tiny slot on the bottom.
Where does throttle cable connect on carburetor?
0:1917:15Route Throttle Cable & Install Carburetors on a CB350 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe left side of the bike route. Over your rubber stopper your holder for your gas tank.MoreThe left side of the bike route. Over your rubber stopper your holder for your gas tank.
How do you install a throttle cable?
0:373:17How to Install Single Cable Throttle Assembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe ferrule like that and set the sleeve into the throttle assembly. Now you're going to take yourMoreThe ferrule like that and set the sleeve into the throttle assembly. Now you're going to take your bottom half and a throttle sleeve. And you're gonna slide it up onto. Your handlebar just like that.
How do you hook up a throttle cable to a Holley carburetor?
0:001:00Attaching Ford Throttle Linkage To A Holley Carb - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe throttle cable connector needs to be installed onto the Holley throttle lever. In theMoreThe throttle cable connector needs to be installed onto the Holley throttle lever. In the approximate location. That mimics the location on the carburetor that you've removed.
How does the throttle work on a carburetor?
Every engine has a means to operate the throttle. With a carburetor, it will be the throttle plate that is opening. A fuel-injected engine will have a throttle body; a diesel uses an injection pump. If the throttle cannot achieve full motion, the engine never produces maximum power.
What is carburetor linkage?
Throttle linkage is a collection of mechanical connections between a vehicles accelerator pedal and its throttle body or carburetor.
What does a throttle cable connect to?
A mechanical throttle cable is used to link the accelerator pedal to the engine throttle plate. When the driver pushes down on the pedal, the cable pulls the throttle open, allowing air to enter the engine. Most of the time, a throttle cable will last the life of the vehicle.Aug 10, 2016How to Replace a Car Throttle Cable | YourMechanic Advicehttps://www.yourmechanic.com › article › how-to-replace...https://www.yourmechanic.com › article › how-to-replace...Search for: What does a throttle cable connect to?
How do you hook up a motorcycle throttle cable?
0:082:59How to Install a Motorcycle Throttle with 2 Cables (4 Stroke) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd there is one cable goes one way in this instance the cable goes you slide it into the cutoutMoreAnd there is one cable goes one way in this instance the cable goes you slide it into the cutout rotate the throttle around. You bring the other one.How to Install a Motorcycle Throttle with 2 Cables (4 Stroke) - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you hook up a motorcycle throttle cable?
How do you install a twist throttle cable?
6:0010:52Raptor 700 Twist Throttle Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo once you have your throttle cable just put it in the hole right here and then go ahead and pushMoreSo once you have your throttle cable just put it in the hole right here and then go ahead and push the cable. Through a little bit just like that. And thread in your cable.Raptor 700 Twist Throttle Install - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you install a twist throttle cable?