- Open up your toilet seat and look for metal hinges that sit on vertical pegs. ...
- Lift the toilet seat straight up off the hinges from the upright position. Leave the soft-close seat in the fully open position.
- Set the toilet seat upside-down on a flat work surface. Flip your seat over so that the metal hinges are exposed.
- Pull out the cylindrical dampers on both sides of the back of the seat. Grab the dampers between your fingers.
- Rotate the dampers towards the back of the seat to make it close more slowly. ...
- Slide the hinge dampers back into the hinge assembly. Push the cylindrical damper back into the hole in the hinge assembly on one side.
- Put the toilet seat back on the toilet bowl. Align the holes in the seat’s hinges with the begs on the toilet bowl.
How to fix a toilet that comes on by itself?
There are several parts to the mechanism you need to understand:
- Chain: When you pull the handle, it pulls on a chain inside the toilet tank.
- Flapper: The chain is attached to a flapper, which, when it lifts up, allows new water into the toilet bowl.
- Fill valve: When the water in the tank gets low, a floater or another mechanism triggers the fill valve. This valve will allow the tank to fill from the waterline. ...
How to easily fix a loose toilet seat?
Method 1 Method 1 of 2: Tightening the Seat
- Find the screws and pry up the cover. The back of your toilet seat is usually connected to the toilet with two long screws that run through the porcelain ...
- Center the toilet seat on the toilet. If the seat is loose, then it may wobble back and forth, in and out of alignment with the rim of the ...
- Tighten the bolt. ...
- Apply tension. ...
What is the best soft close toilet seat?
Best Soft Close Toilet Seats Reviews
- BATH ROYALE BR237-00 MasterSuite. The Bath Royale MasterSuite is a high end toilet seat that we strongly recommend. ...
- KOHLER K-4636-0 Cachet. Kohler is among the top 3 manufactures of toilets and they continue to win here. ...
- BATH ROYALE BR606-00 Premium Toilet Seat. ...
- MAYFAIR 1847SLOW 000 Kendall. ...
- Brondell LumaWarm Heated Nightlight Toilet Seat. ...
How to install a slow close toilet seat?
Installation Steps for Toilet Seat Slow Close. First of all, prepare the materials needed to replace the toilet seat. There is mainly one set of toilet cover with fittings, including one set of toilet seat, two screws, two square tenors and two sets of nuts.
Why has my soft close toilet seat stopped working?
If your soft-close seat isn't working like it used to and you can't adjust the hinges, you might have to fix it by replacing the hinge dampers with a new set.
How do you fix a concealed toilet seat?
2:013:10How to fix a toilet seat with hidden fixings - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see there there's a little screw on the top. And we need to tighten up that screw. So we canMoreYou can see there there's a little screw on the top. And we need to tighten up that screw. So we can take a phillips head screwdriver. Tighten that one up nicely. Once we're done we can put our cap.
How do self closing toilet seats work?
In a matter of seconds, self-closing toilet seats will automatically lower your seat and lid. To lower the toilet seat gently with as little noise as possible, they use a special slow-close hinge system that uses a small air cylinder and a spring.
How do you fix a slow close American Standard toilet seat?
STEP 1: Begin by lifting up the seat, and simultaneously press the buttons and pull up to remove it. STEP 2: Remove the hinge covers. STEP 3: Using a screwdriver, tighten the screws – be careful not to overtighten. STEP 4: Replace the hinge covers, and place the seat back onto the toilet hinges.
How do you tighten a quick release toilet seat?
0:471:35How to tighten a loose toilet seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this seat is removed simply by pulling. Up. The caps and using a Phillips head screwdriver theMoreSo this seat is removed simply by pulling. Up. The caps and using a Phillips head screwdriver the longer. The longer the screwdriver the better it makes it easier to type you simply tighten.
How do you adjust a floating toilet seat?
To start off, remove the plastic tabs that cover the head of the seat bolts. If it is a bottom fixing seat, hold the nut underneath the bowl with your hand and tighten the bolt with a screwdriver by turning clockwise. If it is top fixing seat, it has no nuts under the bowl. Just tighten the bolt with a screwdriver.
How do soft close hinges work?
How Do Soft Close Hinges Work? Soft close hinges have a mechanical device built into the hinge that prevents a cabinet door from slamming. It slows down the door and shuts it 'soft'. These devices are also sometimes called self closing hinges.
How do you fix a Kohler soft close toilet seat?
0:091:37Hinge and Damper Replacement - Quiet-Close Toilet Seats - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pull up on the bottom cover to remove. Next take your needle nose pliers. And pull each damperMoreAnd pull up on the bottom cover to remove. Next take your needle nose pliers. And pull each damper inward to release the hinge assembly from the toilet seat.
What to do if your toilet seat breaks?
There is no way to fix a broken toilet seat. All you need to do is to buy a new slow close toilet according to the design of your toilet bowl and install it. Installing a new toilet seat is not so hard.
How to fix a toilet seat that is not working?
Step 1: Check your toilet seat. First you need to check your toilet seat thoroughly. Get a clear idea of the design of your toilet. Now point out the problems. If there is a problem with the hinges then you need to work on it. You need to take out the seat and the lid of the toilet to work with the hinges.
Why does my toilet seat close in slow motion?
So you need to change the hinges to make your toilet seat close in slow motion. If your slow close toilet is too dirty or smelly just wash out the whole thing with soapy water in a gentle way. Stains on the seat and bowl can be removed by washing it properly.
How to take out a toilet seat?
For this step you need to close the seat first. Then flip up the plastic covers of hinges. Slide the seat forward and remove it. Place the seat upside down on a flat surface. The hinges should be facing you.
Why is it important to slow close the toilet seat?
A slow close toilet seat has several advantages. And the biggest one is the seat does not slam. It does not create noise when the seat hits the stool. If you are using your toilet in the middle of the night you have no need to worry about loud noise. It helps to close the toilet lid every time you use the toilet.
Is it safe to use a slow close toilet?
It helps to close the toilet lid every time you use the toilet. Because of the slow close feature, the seat hits the stool very softly. So there is no question of cracking the toilet seat. So you can use it for a long time. This slow close toilet is also very safe for your children.
How to remove a Kohler quiet close toilet seat?
On a Kohler Quiet-Close seat, start by removing the gray cover. Push upward on the two recessed areas on the side of the cover to lift it out. Next, use needle-nose pliers to grasp the "X" on the end of each cylinder and pull inward. This will allow the entire damper assembly to separate from the toilet seat.
Why do toilet seats have a soft close?
Soft-close toilet seats slowly lower when tilted forward. This prevents them from slamming down, which could damage the toilet seat and hinges or wake sleeping members of the family . Dampers control the soft-close action, and these may need to be adjusted or replaced if the lid suddenly starts slamming closed.
How to remove soft close damper on Kohler?
On some models, you might see a small hole on the dampers. Insert a screwdriver into this hole and rotate the damper toward you, then slide it outward to remove it. On a Kohler Quiet-Close seat, start by removing the gray cover.
What does damping grease do to a toilet?
Damping grease will absorb shock and increase resistance when the toilet lid shuts, slowing it down. Advertisement. The damping grease needs to be applied to the inner structure of the soft-close toilet seat dampers. Look for a retaining nut on one end of the damper and remove it with a socket wrench ...
How to get a toilet seat off?
Leave the soft-close seat in the fully open position. Hold the seat at the top and bottom or at both sides and carefully pull it straight up off the metal pegs. If your toilet seat doesn’t lift straight off, try tilting it forward just a few degrees and see if you can lift it off from that position.
How to remove a toilet seat from a toilet?
Slide the seat forward from the down position to remove it. Leave the seat all the way down so that it is resting in the closed position on the toilet bowl. Flip up the plastic hinge covers at the back of the seat, then grasp the seat from the back and pull it straight forward off the toilet.
Why adjust soft close hinges on toilet seat?
The only reason you would need to adjust soft-close hinges is if your soft-close seat is not closing at the right speed. ...
What type of hinges are used on a soft close toilet?
Metal peg-style hinges are 1 of the 2 main types of hinge assemblies that soft-close toilet seats may use. Look for metal pegs coming up from round plates attached to the back of the toilet bowl, which the hinges on the toilet seat slide onto.
How does a soft close toilet seat work?
Some soft-close toilet seat hinges can be adjusted to make the seat close more slowly.
Is a soft close toilet seat adjustable?
Not all soft-close toilet seat hinges are adjustable. If there are notches on the dampers that make it so you can only take them in and out in 1 position, they are not adjustable. If your hinges are adjustable, they may be hexagonal or have multiple notches that allow you to put them in at different positions.
Do all toilet seats have hinges?
However, not all soft-close toilet seats have adjustable hinges, but you’ll have to remove the seat and inspect the hinges to find out if yours are adjustable. If your soft-close seat isn’t working like it used to and you can’t adjust the hinges, you might have to fix it by replacing the hinge dampers with a new set.
How to fix a toilet that is not level?
If it’s not level, you will need some toilet wedges to fix the problem. Simply slide them below the toilet, but make sure to do it in the front of the unit. It will give you some extra angle and will probably fix the problem. However, make sure not to push wedges too hard or fast to prevent damage to the wax ring.
Why does my toilet seat fall back?
Toilet Lid is Too Thick. If the combination of your lid and seat is too thick, it might cause the seat to fall back, especially if you have a cover on your seat or lid. You should first try to remove the cover and see if the problem is solved.
Why won't my seat stay up?
The most common reason for a seat that won’t stay up is that it’s installed too far back, especially if it’s not installed by a professional plumber. The angle between the seat and the bowl needs to be beyond 90 degrees or it will fall down. However, you can easily fix that problem. First, loosen the lid by loosening the screws ...
What happens if your toilet is not level?
Toilet Not Level. If your toilet is not level, there are high chances that the seat won’t stay up. To be completely sure, find a level and put it on a closed lid. If you don’t own a level, you can download a level application on your phone. If it’s not level, you will need some toilet wedges to fix the problem.
How to fix a loose screw?
To fix it, you should start by checking if the screws are loose. It might be caused by wearing due to everyday use, or due to residue build-up. First, remove the screws with a screwdriver, but if the screws spin, you should use a wrench and pliers to hold them in place.
Can you move a toilet seat?
If the size is not correct, the spacers might slip and cause the seat to move. Note that toilets can be either round or elongated. If you bought an elongated seat for a round toilet or vice versa, it will definitely move. In that case, you can only try buying a completely new seat.
Can you use a wrench to tighten screws?
They are probably not too tight , but you might still need to use a wrench. Also, make sure not to over-tighten them later, or the material might break. If you have trouble with loosening the screws, you can use a screwdriver to keep it from spinning.
What Is a Slow-Close Toilet Seat?
Slow-close toilet seats—as their name implies—close very slowly, but the cool thing is that they close on their own. Of course you will have to give the seat a little nudge, but once you do the tensioned hinges will take care of the rest.
Why Slow-Close Toilet Seats Are Purchased
It was briefly mentioned above, but more attention to this attractive quality should be given. With a slow-close toilet seat, you don’t have to worry about the lid slamming down after you get up from the toilet.
Related Questions
Installing a slow-close toilet seat is something you can do on your own. All you need is a screwdriver.
