- Loosen up the bumper clips. To fix the bumper dent, we first heat up the dent. Most importantly, you will need to get your hand behind the dent.
- Heat up the dented area in your bumper. In our case, we are using a hot air gun. Set the hot air gun at 650 degrees Fahrenheit. ...
- Get dent out of the bumper. Now it is time to get the dent out of the bumper. ...
- Use a metal plate to lower any high bumper spots. You will be able to push the bumper dent out, but you may notice that there may be a few ...
- Use paint scratch remover to clean dent. Now it is time to clean the area. ...
- Use matching paint to fix any scratches. If your bumper was severely hit and there is paint damage, you can use a matching spray paint mix to fix these scratches.
How much does it cost to fix a dented bumper?
Inusrance.com, in this car body repair article, said the average cost to repair a dented bumper could be as little as $450 for a repair to as much as $900+ for a replacement. Western Auto Body, a collision shop located in California, broke down the costs, including parts, paint and labor time.
How to fix a dent in your bumper?
Part 2 of 2: Repair a cracked bumper
- ¼ inch burrowing tool
- Air compressor suitable for tool usage (you will only need an air compressor if you are using air powered tools)
- Angle grinder
- Body filler such as Bondo
- Drill or dremel to fit burrowing tool
- Dust mask
- Jack
- Jack stands
- Masking paper or newspaper
- Paint brush
How do you fix a bumper Dent?
- Scrub the bumper with dish soap and water using a dish scrubbing pad.
- Sand the entire rubber bumper with 80-grit sandpaper to remove all of the paint.
- Wave a heat gun across the back and front of the bumper wherever there is a dent or blemish.
How to repair dented bumper?
• Heat gun, hair dryer, or hot water. • Rubber-tipped tool or dowel. Depending on the location of the dent on your bumper, you may need to remove the fender liner ahead of the front tire (see above) or a lower aerodynamic valance below the bumper to gain access to the interior of the dent. Both can be unclipped manually.
How do you get a dent out of a rubber bumper?
If the dent is on the plastic bumper (or another area of your car made of plastic), applying boiling water to the blemished area should take the dent right out. Boil a pot of water and pour it on the area with the dent, and then reach behind the bumper and push until the dent pops out.
Can rubber car bumpers be repaired?
0:245:33Plastic Rubber Bumper Repair Tips - Replace or Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike this one here ok this looks pretty severe right but this stuff can be repaired all you got toMoreLike this one here ok this looks pretty severe right but this stuff can be repaired all you got to do is get a heat gun or a hair dryer. Make sure you get it nice and hot.
Can you fix a dent in a bumper without replacing it?
By using the correct amount of heat and pressure, it is possible to reshape the bumper without causing more damage to it. Applying the correct amount of heat in the right area makes all the difference.
How do you fix a dented bumper without removing it?
0:261:51How to fix a dent on the front or rear bumper cover on your ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying theMoreYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying the heat to the surface push out the dent using piece of wood.
How do you fix a gouge in a plastic bumper?
1:3415:493M Plastic Bumper Cosmetic Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll we're really trying to do is just knock down this cliff edge on the edges of the gouges. AndMoreAll we're really trying to do is just knock down this cliff edge on the edges of the gouges. And also if you no doubt know anytime you contact plastic with a high-speed tool you melt the plastic.
How do you fix a chip in a plastic bumper?
Here are the basic steps for fixing a paint chip on a plastic bumper:Using sandpaper, smooth down the chipped area.Fill the chip with putty and apply mesh reinforcement if necessary.Allow to dry and sand down until smooth.Paint the repaired area.
Can you pop out a dent in a plastic bumper?
Aim a heat gun or hair dryer at the dented area for about three minutes. Pay close attention to make sure it's not damaging the paint. When it's hot, try to pop out the dent. Use a suction dent puller to grab and pull the dented portion back into its original form.
How do you get a dent out of a bumper with hot water?
Fill a pot with water and bring it to a rolling boil. Carefully pour the water over the surface of the dent to heat up the metal. Allow the metal to flex and return to its original shape. If the bumper is plastic, push the dent out from behind after you pour the hot water over it.
How do you pop out dents?
First, heat the dent with the hairdryer approximately six inches away for about 30 seconds. Then cover the dent with a piece of aluminum foil and rub dry ice over it. The rapid change from hot to cold should make the dent pop out within a minute or so. Another temperature trick involves boiling water.
Do dent pullers work?
Do they work? Dent pullers only work on shallow dents that are positioned on a flat, flexible surface. They can improve the appearance of car dents but are unlikely to create a perfect finish. Unfortunately, DIY dent pullers will not work on deep, angular dents or damage along the edges of bodywork.
How does hot water fix a dent in a car?
Use boiling water Simply boil water in a teapot, protect yourself from burns with rubber gloves, and have a pot of cold water on hand. Then, pour the hot water from the teapot over the dent. Before it cools down, pop the dent out from the inside.
How much does it cost to fix dent in front bumper?
If you just need to have the dent pulled back out and into place, the repair will likely cost $50-$100. However, if the dent is very deep and the paint was damaged as well, you could be looking at a repair of around $200-$1,000, depending on the dent and your chosen repair shop.
Money-saving steps to repair this common problem
When you shop through retailer links on our site, we may earn affiliate commissions. 100% of the fees we collect are used to support our nonprofit mission. Learn more.
Get Access Behind the Bumper
Depending on the location of the dent on your bumper, you may need to remove the fender liner ahead of the front tire (see above) or a lower aerodynamic valance below the bumper to gain access to the interior of the dent. Both can be unclipped manually.
Apply Heat to the Dent
Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don’t apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
Gently Push Out the Dent
Use a rubber-tipped dowel or specialty tool (like the one shown in the illustration, readily available online) to push out the dent from the interior until it begins to pop back into its intended shape. You may need to gently work on any small indents with the tool to get a smooth surface. Then replace the fender liner.
How to fix a sagging bumper?
Fill damaged areas with a flexible plastic filler, available at most auto parts stores. Overfill the damaged area and then smooth, using a piece of cardstock. Allow the filler to dry for a few hours or until smooth to the touch without being sticky. Sand with 180-grit sandpaper to remove any lumps that do not match the contour of the bumper. Repeat if the blemish is still visible or mistakes need to be corrected.
How to remove bumper stickers from a car?
Step 1. Scrub the bumper with dish soap and water using a dish scrubbing pad. Scrub again with a plastic/rubber cleaner. Remove any bumper stickers by soaking the sticker with vegetable oil. Unscrew any reflectors attached to the bumper.
Can rubber bumpers be repaired?
The good news for car owners is that rubber bumper damage can be easily and inexpensively repaired. All that is needed to repair some minor damaged areas is a heat gun, which can be found at most hardware stores.
