How to Install Curtain Holdbacks
- Look at the window treatment that covers your windows. ...
- Make a pencil mark on one side of the window where you want to set the curtain holder. ...
- Measure the location of the curtain holdback from the bottom of the floor on the side you marked and repeat on its opposite side and make a mark.
- Hold the curtain hook drawback or medallion post bracket level at the penciled location, and make a mark through the holes for the screws with the pencil.
- Make a small pilot hole with the drill and drill bit sized to the fastener if you are installing screws.
- Drill a hole sized to the toggle bolt with a drill bit if you are installing in drywall without a stud behind it.
- Insert the toggle bolt wings by holding them while they're collapsed through the hole until they open inside the wall.
- Place a level on the hook-shaped curtain holdbacks and readjust as necessary to ensure they are level.
How to properly install a curtain holdback?
Things You'll Need
- Measuring tape
- Pencil
- Hammer
- Small nails or tacks
How do you make tie backs for curtains?
Our 12 Favorite DIY Curtain Tiebacks
- Wooden Beads on a Rope. Start with a rope and add some wooden beads. ...
- Rose Vines. This curtain tieback look like a sweet vine of roses. ...
- Fabric Bow. ...
- Star Tieback. ...
- Silver Ropes. ...
- Knotted Rope. ...
- Simple Bow. ...
- Decorative Ribbon. ...
- Shell Tassel. ...
- Cord Covers. ...
How to make professional tie backs for curtains?
Things You Will Need
- Curtains
- Measuring tape
- Chalk
- Scissors
- Interfacing
- Clothes iron
- Pins
- Tweezers
- Needle
- Thread
Where to place tie backs for curtains?
The Correct Way to Install Metal Tie Backs for Drapes
- Measure from the bottom of your curtains to the rod they are hanging on. Divide this number by three.
- Determine what look you want for your window treatments. ...
- Remove your drapes, with the rod, from the window and set them aside.
- Mark the location for your metal tie back based on the one-third or two-third rule on the wall. ...
How do you fit curtain holdbacks?
0:173:50Installing Curtain Holdbacks - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo go ahead and place it again just make sure it's flush and not getting in the way of the trim.MoreSo go ahead and place it again just make sure it's flush and not getting in the way of the trim. Mark that and install that one all right so I have these holes drilled or marked.
Where do I put holdbacks?
Measure the location of the curtain holdback from the bottom of the floor on the side you marked and repeat on its opposite side and make a mark. Most curtain holdbacks are installed between 40 to 48 inches up from the floor, but it is a personal choice where you install them.
How do you secure curtain tie backs to the wall?
2:286:20How To Install Curtain Tie Back Hooks - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor the height of where your tie back is going to be situated. Four inches away from the windowMoreFor the height of where your tie back is going to be situated. Four inches away from the window frame that's where your tie back is going to start.
How do you put on curtain tie back hooks?
0:000:51Where To Fit Curtain Tie Back hooks For The Best Look - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd moving it up and down a little bit just to see where looks best the rough rule of thumb is thatMoreAnd moving it up and down a little bit just to see where looks best the rough rule of thumb is that the hook should be located 2/3 away down the curtain.
Do curtains need tie backs?
Without tiebacks, curtains can look plain and unfinished. Curtain tiebacks add a decorative touch and are made with a variety of materials. Tiebacks can dress a curtain up or down and can match or contrast with the curtain's color.
How do you install a curtain rod holder?
3:405:32Installing Curtain Rod - Hang Curtain Rod - EASY DIY - How to - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make any adjust as far as how far states often either in and then after that we could tightenMoreAnd make any adjust as far as how far states often either in and then after that we could tighten our little wing nuts back down by him okay we're assembling the curtain rod.
Where should curtain brackets be placed?
Each bracket should be placed at the height you previously determined and about four to six inches from the side of the window frame. (This will allow you to open the curtains completely.) Check to make sure your pencil marks are level otherwise the entire window treatment will be crooked.
How high should curtain ties be?
To achieve proper placement, again measure the length of the curtains and divide by three. Hang each tieback a third of the way up from the bottom of the curtain. If, for example, the drape is 100 inches long, you would place the tieback 33 inches from the bottom.
How to hang curtains from curtain rods?
Hang the curtains from the curtain rods. Slide the drapery holdbacks around the curtains and hold the tiebacks in place against the wall. Have a friend hold the curtains in position as you step away from the window to check how the curtains drape from the tiebacks.
How to adjust curtain tiebacks?
Adjust the holdbacks up or down to get different looks. Mark the final position for the curtain tiebacks. Check for levelness again. Erase any marks you made on the wall other than the final location.
What are curtain holdbacks?
Curtain holdbacks add a finishing touch to your window treatments or door openings. While not absolutely necessary for any window, curtain tiebacks quickly and easily change the appearance of the window treatment. If the curtains cover a patio door, the drapery holdbacks serve the function of moving the curtain out of the way so there is easy access to the door. Installation of curtain holdbacks is a simple process. Just about anyone can install them with a few basic tools that are probably already in the house.
How do I measure for curtains?
Step 1. Measure a spot about 2/3 of the way between the curtain rods and the floor. If the curtains don't go all the way to the floor, measure from the curtain rods to the bottom of the length of the curtains. Make a light mark on the wall.
What is a drapery holdback?
If the curtains cover a patio door, the drapery holdbacks serve the function of moving the curtain out of the way so there is easy access to the door. Installation of curtain holdbacks is a simple process. Just about anyone can install them with a few basic tools that are probably already in the house. Advertisement.
What do you need to know about curtain hold backs?
Everything you Need to Know About Curtain Hold Backs, Tie Backs and Accessories. Finishing touches are very important when it comes to dressing your windows and never more so than with curtains. Extra touches and accessories can really finish off a window treatment and make all the difference between a stunning looking window ...
What is a tie back curtain?
The curtain is pleated into soft folds or pleats once it is hung and a tie-back is then placed around all of the pleats to hold them in place and also to pull the leading (front) edge of the curtains back a little off the window area.
What type of tie backs are there?
Generally, the types include: Decorative ruched tie backs, tassel tie backs and pendulum tie backs. In many instances you might find hold backs included in this, but as we have discussed above there are distinguishing differences between the two.
What are tie backs made of?
Tie-backs are made from soft and flexible material, usually of the same fabric as the curtains, or of twisted, satin rope with an ornamental tassel at the front. However, there is no limitation to what they can be made of really so long as they are flexible and not rigid; and you can find wire and bead versions, crystal glass ones, ribbon ones and many other materials creatively used to make tie-backs including everything from shells to twigs, branches and even metal chains. If you’re not the arty and creative type though or you’re not one for bringing the outdoors indoors, then you only need to pop over home wares section to find a fabulous selection of ready-made, stylish and impressive tie-backs. Or if you’re ordering from our extensive collection of made to measure curtains then don’t forget you can add matching tie-backs to your order.
What is a curtain boss?
Curtain bosses, also sometimes known as ombres or mushrooms, are available in many designs, colours and sizes and in both ornate and very simple designs and in both metal or wood to coordinate with your choice of curtain pole.
Where are tie backs secured?
And as where tie-backs are secured to a hook at the trailing (back) edge of the curtains , hold-backs are fixed at the leading (front) edge of the curtain, as close to the edge of the window recess as possible. This is because hold-backs are only intended to hold only the front edge of the curtain back slightly off the window are ...
When are the tie backs released from the hooks?
If the curtains are full working curtains then the tie-backs are release from the hooks before the curtains are drawn together into the closed position and replaced again once the curtains are opened.
Where and What Direction to Place Curtain Holdbacks
Hi all - I'm a frequent lurker and infrequent poster at this site. Thank you all for everything I've learned from you.
Comments (2)
Picture would be helpful...it depends on how much window you want showing...the lower the hooks, the less glass you'll see. I have seen them angled and straight. I think angling is ok with a fuller drape. Look at pics on line and see what you like...especially if it matches the style of the room and the drapes.
