How to Finish the Drywall Around a Bathtub Flange
- Step 1. Fill with joint compound any large gaps where the drywall meets the flange. Push in enough to make the surfaces...
- Step 2. Apply a band of joint compound roughly 6 inches wide to the drywall edges that meet the flange, using a 6-inch...
- Step 3. Lay paper drywall tape over the bands of compound so that it butts up...
How to fix the drywall around your bathtub?
How to Hang Drywall Around a Bathtub
- Measure the Bathtub Area. Measure the horizontal dimension of the bathtub's rear wall. ...
- Cut Water-Resistant Drywall. Cut a length of water-resistant drywall according to the measurements, using a utility knife or drywall saw.
- Secure Drywall With Screws. ...
- Measure the Drain End Wall. ...
- Cut Holes for Faucets. ...
- Install Side Wall Drywall. ...
- Tape, Mud and Sand Joints. ...
How to finish drywall around tub or shower surround?
Tools That You Will Need:
- Screwdriver set.
- Chalk Line.
- Drill.
- Hammer.
- Level.
- Pry Bar.
- Safety glasses.
- Ladder.
- T-square.
- Tapes.
How to drywall a bathroom in 20 minutes?
- Cement board – infused with cement for waterproofing.
- Greenboard – tinted green and finished with thick wax paper for waterproofing.
- Blueboard – tinted blue and infused with gypsum crystals for better bonding.
- Whiteboard – standard sheetrock, and it’s the most common kind.
How to install drywall over a tub or shower flange?
Things You'll Need
- Paper Drywall Tape
- 150-Grit Sandpaper
- Joint Compound
- 6 Inch Drywall Knife
- Silicone Caulk
How do you drywall around a bathtub?
How to Hang Drywall Around a BathtubStep 1: Measure the Bathtub Area. ... Step 2: Cut Water-Resistant Drywall. ... Step 3: Secure Drywall With Screws. ... Step 4: Measure the Drain End Wall. ... Step 5: Cut Holes for Faucets. ... Step 6: Install Side Wall Drywall. ... Step 7: Tape, Mud and Sand Joints.
How do you finish the edges of a bathtub?
0:007:24By uh just putting it in the system which is in and then just measuring over with the table saw andMoreBy uh just putting it in the system which is in and then just measuring over with the table saw and cutting whatever scraps of plywood or whatever you have around i have a some 3 8 plywood.
Does drywall go over tub flange?
We've done the research to provide you with the answers you need to install your bathtub properly. Whether backer board or drywall, your surround material should rest on the edge of the tub flange but should not make contact with the lip.
How do you fill the gap between drywall and shower surround?
Filling the gap means cutting the sheetrock so that it runs up to the edge of the enclosure's mounting flange, pre-filling the recess with hot mud (setting compound), then taping and finishing with standard drywall compound to cover the joint.
How do you put trim around a bathtub?
2:114:23Around the room so the right side of each piece of trim will be coped. And the other side will beMoreAround the room so the right side of each piece of trim will be coped. And the other side will be just a square cut. So we've decided to drop our inverted base molding down one inch from the ceiling.
How do you install trim around a tub surround?
0:572:59Not from the end cut the trim piece to proper length repeat for the other. Side. Now dispense theMoreNot from the end cut the trim piece to proper length repeat for the other. Side. Now dispense the adhesive onto the back side of the sidewall trim piece and install as shown.
Can you put drywall around a tub?
0:365:44And then as the tub flange can flares out away from the wall. I'm going to change it down to aMoreAnd then as the tub flange can flares out away from the wall. I'm going to change it down to a quarter inch piece of sheetrock. I've inserted these little shims. So that it's closer to a quarter inch.
What kind of drywall goes around a bathtub?
Green drywall is a type of drywall that's mold resistant and is used in applications where moisture can be an issue—so most commonly, bathrooms. To maximize the mold resistance, use mold-resistant drywall mud, aka joint compound. Green drywall generally costs about 20% more than regular drywall.
What kind of drywall goes behind a tub surround?
Don't use paper-faced backer board, i.e., paper-faced drywall, behind seamed tub and shower enclosures. Use an alternate approved product such as fiber-cement, fiber-reinforced gypsum, glass mat gypsum, or fiber mat-reinforced cementitious backer panels.
How do you seal a large gap between a wall and a bath?
0:432:18And cut a very small angle about an eighth of an inch off the top. You're going to cut it at about aMoreAnd cut a very small angle about an eighth of an inch off the top. You're going to cut it at about a 45 degree angle. Now taking your caulking gun go ahead and load up your caulk.
How do you waterproof drywall in a shower?
It is possible to waterproof drywall in a shower by covering the drywall with a waterproof membrane. This waterproof membrane can be bonded to drywall with thinset adhesive to create a waterproof layer. Never tile directly over drywall in a shower.
How do you finish a wall over a shower surround?
1:4511:26Our piece up here too. So again remember your half inch side here your wider side goes into the wallMoreOur piece up here too. So again remember your half inch side here your wider side goes into the wall. And we're going to spray both the wall. And the edge of the trim.
How long does it take for drywall to dry?
Allow the compound time to turn white, indicating it is dry, which typically takes no more than 24 hours.
What is a bathtub rim?
A bathtub's flange, or rim, adjoins the surrounding bathroom surfaces. Generally, the surfaces around the bathtub are tiled, which provides superior water resistance, and are easy to clean. But some bathtubs have drywall surrounds.
Can you rip out drywall to prevent mold?
In severe cases, you might have to rip out the drywall to deal with the mold problem within the wall. To avoid this, fill large gaps with joint compound and then seal the joint with silicone caulk. Advertisement. Seal your bathtub to prevent moisture damage. Image Credit: Jupiterimages/Photos.com/Getty Images.
Can you use masking tape on a bathtub?
You can use masking tape to keep the bathtub’s flange clean while you work, but don’t let the masking tape get caught underneath the joint compound and caulk otherwise you risk compromising the seal . Advertisement.
Step 1: Measure the Bathtub Area
Measure the horizontal dimension of the bathtub's rear wall. These measurements help you cut the first pieces of drywall for the tub surround.
Step 2: Cut Water-Resistant Drywall
Cut a length of water-resistant drywall according to the measurements, using a utility knife or drywall saw. The walls surrounding the tub need to use water-resistant drywall or, preferably, cement board instead of regular drywall to protect them from moisture damage.
Step 3: Secure Drywall With Screws
Position the cut piece of water-resistant drywall horizontally against the bathtub's rear wall and rest its bottom edge on the lip of the bathtub ledge. Make certain the sheet is held level, then secure the piece to the wall framing using galvanized or coated drywall screws to prevent rusting.
Step 4: Measure the Drain End Wall
Begin the bathtub's drain end wall installation at the same level at the rear wall, measuring the length of drywall to be cut to the appropriate wall stud center line.
Step 5: Cut Holes for Faucets
Measure the locations of the tub faucet and valve locations, then transfer this layout to the water-resistant drywall piece you cut for the wall. Cut out the holes necessary using a utility knife or drywall jab saw.
Step 6: Install Side Wall Drywall
Place the side wall water-resistant drywall piece into position, against the wall framing that was placed over the valves and faucet. Level the piece and secure it in place using drywall screws. Repeat for the next piece of water-resistant drywall above the previously installed sheet.
Step 7: Tape, Mud and Sand Joints
Tape and mud all of the drywall joints and screws prior to applying the planned wall finish. Apply self-adhesive fiberglass drywall tape to all joints or use joint compound to adhere fiberglass drywall tape. Avoid paper drywall tape, which isn't moisture-resistant.
Can concrete board be used as drywall?
The concrete board will take a texture just as well as drywall (but note that the texture chosen might be made of water-soluble mud too). Consider that if you have that much water damage to the drywall you may have moisture in the cavity as well.
Is drywall compound water soluble?
Drywall compound is most often water soluble. The method of repair will depend on your use case and the type of finish desired. If you remove the drywall you could replace it with a cement board which can be taped with special tape and compound.
Can you cover drywall with mesh tape?
You could fill the gap between the flange and the drywall with hot mud and hope it adheres to the caulk well enough for years’ worth of showers and baths, then cover it with mesh tape. You could go through the labor-intensive, time-consuming process of furring your studs before hanging the drywall.
Can you finish drywall around a shower flange?
Finishing Drywall Around a Shower Flange. Drywall is typically a one-stop-shop for resilient interior walls — and it’s no wonder why, since it’s affordable, durable and stands up to smoke and fire better than many other building materials. But there’s one massive exception: it’s no match for especially moisture-rich environments.
Can you use mud legs on shower flange?
The extra-long mud leg can span the gap between the drywall and shower flange, and is installed with staples — so you won’t need to drill down into the tub/shower enclosure. Finishing drywall around a shower flange doesn’t have to be a pain, and by using Shower Bead, you’re going to save time, material and headaches.
Can you use drywall as a backer for tile?
That makes finishing drywall around a shower flange or tub enclosure tricky, because using drywall as a backer for tile in these areas is likely going to lead to ruining both . Paper tape, too, should be right out — it serves as a food source for mold. Connecting the drywall to the shower enclosure, then, requires a different solution ...
Does shower bead use drywall?
Shower Bead uses less drywall compound than filling the gap. No messy drywall compound on the shower surround, the tear-off strip protects it. No paper tape needed, which means eliminating a source of mold growth. No screws needed.
How do I fill a gap in drywall?
Prefill the gap and get it basically flush with face of the drywall. Then tape and mud the area basically like normal. This is because that thick mud will crack if it is not taped over. Place the tape against the surround edge and cover the gap area that you profilled . Then next coat basically I treat like one side of an inside corner. Applying the mud on a slight bevel so that you are covering the tape and feathering outer edge out to nothing. Many times this is all that is needed. Sand and prep for paint. It works very well.#N#When I’m covering with tile I just fill the gap with mud and sand flat while sanding other muddled areas. No taping required.
Can you butt up against a drywall flange?
The problem with going over the lip is that it bends the drywall at the lip, which doesn 't look particularly good, notching the back out to accommodate the lip is the better way to go IF there is enough thickness of drywall to do so. On the left side with bare stud, it looks like you can butt up against the flange.
Does drywall go over the lip?
Typically, drywall butts to or goes over the lip. In cases where it butts to the lip, you will then need to finish the transition with either tile or trim. In cases where it goes over the lip, the drywall is finished as usual.
6 Steps To Finish Drywall Around A Shower
There are many solutions for installing drywall around a shower. Some put hot mud between the flange and the drywall. Some furs the studs before hanging the drywall.
6 Advantages Of Using Shower Bead To Finish Drywall Around A Shower
Now we will explain why using a shower bead is the best way to do the finishing of drywall around a shower.
5. Saves Time
Using a shower bead to finish the drywall around your shower will take less time than all the other options of doing the job. In today’s busy world, it means a lot to many people.
6. More Durable
Shower beads are manufactured using PVC. It means it will never get rusty and will never host any molds, no matter how moist it remains.
Commonly Asked Questions About Finishing Drywall Around Shower
A waterproofing primer is the best solution to make a drywall waterproof, which is right beside the shower. There are two basic types of waterproofing primes on the market. One is based on latex and the other is based on oil. Their main purpose is to prevent the surface from molds and mildews.
Bottom Line
Finishing the drywall around a shower is a serious task. You cannot do any experiment on this. Because it may compromise the hygiene level of your house. If you follow the steps described in this article meticulously, you will not need to worry about the shower wall for a long period.
