how do you drain a ge front load washer

How do you drain the water out of a GE washing machine?

• STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one.
• STEP 2: Locate the drain hose and water supply hoses.
• STEP 3: Drain the washing machine of water.
• STEP 4: Remove a drain hose clog.
• STEP 5: Remove a drain pump clog.

Full Answer

Where is the drain hose on a whirlpool front load washer?

The clip attaches to the hose and to the back of the washer. The discharge height MUST NOT BE LESS THAN 24 INCHES and no more than 8 feet above the base of a Front Load washer. Note: Front Load washers do not come with or use a Drain Hose Clip due to the design of the drain hose on the washer.

How do I drain the water from my Kenmore Elite washer?

The washer will automatically drain if left in a paused state with the lid closed for more than 24 hours and water is present. If you need to drain out the water and spin the clothes, you must select the "Spin Only" or "Drain and Spin" cycle, then press the "Start/Pause" button. You may drain and spin a cycle during any wash cycle.

How do you drain and spin a washing machine?

You may drain and spin a cycle during any wash cycle. While the washer is operating, turn the Cycle Selector knob to "Spin Only" or "Drain and Spin.". The washer will stop and reset the cycle to the new selection. Press "Start" to begin the new cycle selection.

What is the discharge height of a power washer drain hose?

Drain Hose Installation Requirements Water may be drained into a standpipe or set tub. The discharge height MUST NOT BE LESS THAN 30 INCHES and no more than 8 feet above the base of the washer. Note: If the drain is not 30", use the Anti-Siphon Clip provided with the install kit to lift up the drain hose.

How do you drain the water out of a GE front load washer?

1:313:02Front Load Washer Pump Clean Out - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the filter counterclockwise slowly to control the amount of water being released remove theMoreTurn the filter counterclockwise slowly to control the amount of water being released remove the filter and allow the water to drain into the tray.

How do I get my GE washer to drain and spin?

If the washer is running, press the "Start/Pause" pad once to interrupt the cycle, then select "Drain and Spin" and press the "Start/Pause" pad again. If the "Stop" pad has been selected and the washer is still full of water, select "Drain and Spin" and then press "Start".

How do I manually drain my washing machine?

If not, follow these steps:Step 1: Turn off the power and lay down towels.Step 2: Locate the drain hose at the back of the washing machine.Step 3: Drain the water.Step 1: Turn off the power and lay down towels.Step 2: Locate the drain hose.Step 3: Drain the water.Step 4: Scrub the filter.

How do I drain the front of my washing machine?

How to Drain a Front-Loading Washing MachineSTEP 1: Turn off the power. Switch the power button off, if your model has one. ... STEP 2: Locate the drain pump filter and/or drain tube. ... STEP 3: Drain the water. ... STEP 4: Clean the filter. ... STEP 5: Know when to call in a pro.

Why is my GE front load washer not draining?

0:1313:27GE Front Load Washer Won't Drain or Spin - Ideas to Troubleshoot & FixYouTubeStart of suggested clipEnd of suggested clipWell make sure that the drain hose isn't stuck too far down into your stand pipe the reason is if itMoreWell make sure that the drain hose isn't stuck too far down into your stand pipe the reason is if it goes down too far into the stand pipe it could cause water siphoning and backflow.

Why won't my GE washer not drain?

A kink or clog in your washing machine's drain hose could be interfering with water flow and preventing your machine from draining properly. To inspect the drain hose, turn off the power to the washer, disconnect the hose (have a bucket ready to catch any water), and check the hose for damage or obstructions.

How do you drain a washing machine mid cycle?

1:212:04Tip #5 Stopping a washing machine mid cycle - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull out the hose onto a tray unplug the hose. And allow the water to drain fully secure the cap andMorePull out the hose onto a tray unplug the hose. And allow the water to drain fully secure the cap and pop the hose back into the machine.

Does Spin cycle drain water?

It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. The drain hose loops to the top of the machine, and then down to the drain, enabling the tub to fill. When the water reaches the bend in the hose, it goes out of the drain.

How do you drain a washer that won't drain?

What to Do When Your Washing Machine Won't DrainPerform a Master Reset. Unplug your washer for about one minute. ... Test the Lid Switch Assembly. ... See if the Drain Hose is Kinked. ... Check the Drain Hose or Pump for Clogs. ... Clean out the Coin Trap. ... Check the Water Level Control. ... Schedule Washing Machine Repair.

Why is there water left in my front load washer?

Your lid mechanism is broken or not engaging fully. Your drain or hose is clogged. Your load was too large for a good spin cycle. Your washing machine's sensors are damaged or old.

Do all front load washers have to be drained?

Solution: Front-loading machines are designed to not open unless all of the water is emptied. So, if it will not open, chances are good that it is because some water remains. Manually activate the “Drain/Spin” cycle.

Why is my GE washer not draining or spinning?

When your GE top load washer isn't draining or spinning, the first thing you should look at is the drain hose. Make sure it's in place and that it's not clogged. Also check it for kinks — if it's taking a turn that's too sharp, it could be causing the washer to get stuck.

How high can a GE washer pump water?

GE/Hotpoint/RCA Top Load, Front Load, and Unitized washers have powerful drain pumps that can pump water vertically as high as 8 feet above the floor. Spacemaker compact washers pump up (5) feet.

Do you need a check valve on a washer?

Provided the washer is installed compliant with the installation instructions, there should be no reason for needing check valves.

How long does it take for a washer to drain water?

If no other selections are made within 24 hours, the washer will drain the water. To spin the clothes, you must select the "Spin Only" or "Drain and Spin" cycle then press "Start.". You may drain and spin a cycle during any wash cycle.

How to stop a washer from running?

If the washer is running, press "Start" once to interrupt the cycle, select "Drain and Spin" and press "Start" again. If "Stop" has been selected and the washer is still full of water, select "Drain and Spin" and press "Start" again.

How to drain water from a washing machine?

Place a shallow pan or dish under the pump access door, and place towels on the floor in front of the washer to protect the floor. It is normal to catch about a cup of water when the filter is removed. Pull down the pour spout. Turn the pump filter counterclockwise and remove the filter. Open slowly to allow the water to drain.

How do I clean a washer pump?

This process is for Front Load Washers with an access cover at the bottom, front of the washer only: 1 Using a coin or flat screwdriver in the notch on the door, open the access door. 2 Place a shallow pan or dish under the pump access door, and place towels on the floor in front of the washer to protect the floor. It is normal to catch about a cup of water when the filter is removed. 3 Pull down the pour spout. 4 Turn the pump filter counterclockwise and remove the filter. Open slowly to allow the water to drain. 5 Clean the debris from the filter. 6 Replace the filter and turn clockwise. Tighten securely. 7 Flip up the pour spout. 8 Close the access door.