- Unplug the Whirlpool Duet washer power cord from the wall outlet. ...
- Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver.
- Locate the pressure switch inside the washer cabinet. From the rear of the washer, the switch will be on the rear left corner of the cabinet.
- Adjust the scale on your ohmmeter to the RX1 or X1 scale. ...
- Test the pressure switch's "suds detect" function. Stick one probe into far right hole and another probe into the hole next to that one.
- Place a probe into the second hole from the left and the other probe in the third hole from the left to test the rinse.
How do I test the pressure sensor on my duet washer?
The pressure sensor is somewhat difficult to test directly, so the easiest way is to visual check that the pressure hose connecting the switch to the tub is not pinched or kinked. and do a Duet Washer Quick Diagnostic Test (the C06 portion of the quick test should fill the washer to "wash level".
How do you fix a whirlpool duet washer that won't turn on?
Use an ohmmeter to determine whether the pressure switch is malfunctioning. Unplug the Whirlpool Duet washer power cord from the wall outlet. Pull the washer away from the back wall far enough that you can slide the top off the washer and get behind the washer.
Where is the pressure switch on a whirlpool washing machine?
Locate the pressure switch inside the washer cabinet. From the rear of the washer, the switch will be on the rear left corner of the cabinet. The pressure switch is round with a wiring harness connecting to the back of the switch.
How do you test a pressure switch on a pressure washer?
Test the pressure switch's "suds detect" function. Stick one probe into far right hole and another probe into the hole next to that one. Again, your ohmmeter should read zero.
How do you check the pressure switch on a Whirlpool washing machine?
Adjust the scale on your ohmmeter to the RX1 or X1 scale. Stick the tips of the ohmmeter probes into the small slots where the wiring harness connects to the switch. Looking at the pressure switch, place one probe into the far left hole and the other probe into the third hole from the left. The reading should be zero.
How do you test a pressure switch on a front load washer?
Testing the SwitchFind the wires leading to the terminals of the switch. ... The water level switch has three terminals. ... Touch the probes to terminals 1 and 3, and note the reading (∞ or approximately 0.0).Touch the probes to terminals 2 and 3, and note the reading.More items...•
How do you test a washing machine pressure sensor?
1:394:05How to Test the Pressure Switch on your Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that's a good reason if you do not get that reading when you hear the diaphragm inside theMoreSo that's a good reason if you do not get that reading when you hear the diaphragm inside the pressure switch click then the pressure switch is bad.
How do you reset the pressure switch on a washing machine?
Some pressure switches have to be reset when the machine is moved or before the machine's first use. To do this put two litres of water inside the drum set the machine to a drain cycle and it will automatically reset the machine.
How do I know if my pressure switch is bad?
How to Tell If Your Well Pump Pressure Switch Is BadYour water pressure is at or above the cut-out pressure, yet the pump doesn't turn off.Your pump doesn't turn on at the proper cut-in pressure.You have low water pressure even though the pump is running.Your pump runs, but it cycles on and off repeatedly.
How do you check a pressure switch?
1:1814:26How to Test Pressure Switch on a Furnace - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first way you can check it is by setting your meter to the ohm symbol or - resistance.MoreSo the first way you can check it is by setting your meter to the ohm symbol or - resistance.
How do I know if my washing machine sensor is bad?
3:258:10Top Loading Washing Machine Load Sensor Troubleshooting and ...YouTubeStart of suggested clipEnd of suggested clipThis hose below on the end of it and see if there's any obstructions. If there is not an obstructionMoreThis hose below on the end of it and see if there's any obstructions. If there is not an obstruction in that and you're reading 120 volts on the other on all the measurements you may have a bad timer.
How do I test a water pressure switch with a multimeter?
Disconnect the wires connected to the pressure switch by pulling the wire connectors off of the switch terminals. Set a multimeter to test for resistance (ohms). Touch each tester probe to one of the switch terminals. The tester should read 0 or close to 0 (indicating no resistance).
How do you adjust a water pressure switch?
1:443:50How to Adjust Washing Machine Water Level Pressure SwitchYouTubeStart of suggested clipEnd of suggested clipIt's pushed inward the most I suspect that over time the spring has weakened. And has changed theMoreIt's pushed inward the most I suspect that over time the spring has weakened. And has changed the calibration. There is a factory seal on the screw adjustment I have a quarter inch socket.
What does pressure switch do?
Pressure switches are important components for controlling the activation and deactivation of pumps in fluid systems when pressure thresholds are reached. They are also used in process control systems for maintaining steady pneumatic or mechanical pressure.
Where is the water level switch on a Whirlpool washer?
1:574:44Water Level Switch - Washer Repair (Whirlpool # 8181695 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy twisting and pulling the hose down next rotate the water level switch counterclockwise at 180MoreBy twisting and pulling the hose down next rotate the water level switch counterclockwise at 180 degrees and pull it straight out to release it from the cabinet.
Why is my washing machine not draining?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.