How do you check the lid switch on a GE washer?
- Turn off the washer and unplug the appliance.
- Locate the retaining tabs and/or screws that hold the top horizontal panel down.
- Look for the lid lock switch on the underside of the top panel and where it fits into the appliance.
- Put the lid back down and plug the washing machine back into the electrical outlet.
Where is the lid switch on a GE washing machine?
Hunker may earn compensation through affiliate links in this story. General Electric, or GE, top-loading washing machines have a lid switch located on the door jamb of the top of the cabinet. The switch is compressed by the lid when the lid is closed and decompresses when the lid is open.
How do I reset the lid lock on my ge washer?
Replace both the lid lock and the control board when the GE washer lid lock reset doens’t work. To unlock the lid, follow the procedure below. Step 1: Remove the four screws and the back panel. Step 2: Remove the two screws holding the top cover on. One is by the power cord and the other is behind the capacitor.
Why won’t my ge washing machine run with the lid open?
Like many washing machines, GE-made washing machines have a safety feature that prevents the washer from running with the lid open. This is done to reduce the risk of water spillage, damage to the components or injury to the user. This feature can be disabled for testing purposes only.
How do I know if my washing machine lid switch is bad?
If the lid switch is damaged, the washer will detect that the lid is open, even if it is not. To determine if your lid switch has no longer functional, you must remove it and test it for continuity using a multimeter.
How do I know if my lid switch washer is bad?
You will need to remove the two-wire harnesses off the lid switch, While you can unmount the lid switch, at this point you only need to test it with a multimeter. Set your multimeter to the lowest ohms of resistance and test your lid switch. If it does not read any continuity, then your lid switch is indeed faulty.
How do you test a washing machine lid switch?
1:144:30You want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicatesMoreYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicates that the lids closed which thatlet's which is good. Now if your lips closed.
How do you test a GE magnetic lid switch?
3:566:20But if it's test good you can reconnect it you're going to need a voltmeter. This is just a simpleMoreBut if it's test good you can reconnect it you're going to need a voltmeter. This is just a simple analog voltmeter you're going to want to test it on ohms.
How do I reset the lid switch on my GE washer?
Top Load Washer - Lid Lock FeatureMake sure the washer is paused (press the Start/Pause button). During the spin cycle, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.Unplug the washer for a minute to reset.
How do you test a lid lock switch?
1:222:34Use a probe to touch one of the terminals. And the other probe to touch the second terminal. NowMoreUse a probe to touch one of the terminals. And the other probe to touch the second terminal. Now actuate the switch. If the meter reading shows zero ohms of resistance. The switch has continuity.
Can I bypass the lid switch on my washer?
3:246:16This switch. So that the washing machine thinks the lid is closed. So that you can simply drain theMoreThis switch. So that the washing machine thinks the lid is closed. So that you can simply drain the water out of your washing.
How do you bypass a 3 wire lid lock switch?
0:522:02This is a noir style lid switch disconnect the wire harness from the lid switch. Place the jumperMoreThis is a noir style lid switch disconnect the wire harness from the lid switch. Place the jumper wire between the gray and white wires. And put electrical tape on it to insulate the connection.
How do I fix the lid lock on my GE washer?
1:297:22You push in toward you and then lift up and that'll come up. And then the backside of it the partMoreYou push in toward you and then lift up and that'll come up. And then the backside of it the part closest to you you can pull out away from you and then you're gonna take here's that little tab.
How do I reset the lid lock on my Whirlpool washer?
If your lid lock light is flashing, you can unplug your washer for 10 minutes and plug it back in to reset the washer and the flashing light. You can also press and hold the 'End of Cycle' button for 20 seconds to reset the washer and flashing lid lock light.
Is there a reset button on my GE washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Why is my GE washer not turning on?
Here's how to assess for power issues when your GE washer won't start: Check the power cord: Make sure it's completely plugged into a functioning outlet and free of damage. Avoid extension cords: They can't reliably transmit the voltage a washer requires, resulting in surges that interrupt power.
What would cause a GE washer to not spin?
A loss of electrical power to the washer will cause a failure to spin. To check for power at the outlet, carefully plug a small table lamp or hair dryer into the wall outlet and turn it on. If it does not work, you may have blown a fuse, tripped a circuit breaker or have a defective wall outlet.
Why do washing machines have lid locks?
The main purpose of the lid switch is to detect when the washing machines lid is open so that the washer won’t start until the lid is safely closed. In addition to that safety measure is a lid lock that safely locks the lid during the spin cycle. That way the spinning parts of the washer cannot possibly hurt anyone operating the washer. Only a VMW type of washing machine needs a lid lock because it doesn’t include any braking mechanism and only comes to a stop within up to 30 seconds. On the other hand, direct drive washing machine models have brakes to stop almost instantly, so they don’t include any lid locks.
Why won't my washer start a spin cycle?
A good indication that the lid switch or the lid lock may not be correctly working shows with the lid lock light flashing. If the lid switch can’t detect that the washer lid is closed, then the washing machine won’t start a spin cycle. The problem may therefore be solved by replacing the lid switch or the lid lock after carrying out some tests ...
What happens if you don't have continuity on a lid lock?
If there is no continuity, then you will have to replace the lid lock. The other test is for the lid lock solenoid and this includes testing for continuity across the yellow and the white wires. Your multimeter should read between 85 to 155 ohms of resistance. But in case you don’t get that, then it means you should replace the lid lock.
What to do when GE washer lid won't unlock?
What to Do When Your GE Washer Lid Won’t Unlock. All you want to do is get the laundry done. So when your GE washer lid won’t unlock, your mission comes to a screeching halt. Luckily, there may be a simple solution. Some washers have lid locks that are heat activated.
How to unlock a spherical cylinder?
To unlock the lid, follow the procedure below. Step 1: Remove the four screws and the back panel. Step 2: Remove the two screws holding the top cover on. One is by the power cord and the other is behind the capacitor. Step 3: Now the top cover can be removed.
Why is my GE washing machine not running with the lid open?
Like many washing machines, GE-made washing machines have a safety feature that prevents the washer from running with the lid open. This is done to reduce the risk of water spillage, damage to the components or injury to the user. This feature can be disabled for testing purposes only. This allows you to inspect the inside ...
Can you use a washer with a lid switch disabled?
Warning. Never use the washer for regular use with the lid switch disabled. This process is only for testing to ensure the tub spins, water fills and drains and the agitator works. Do not work on the washer while it is turned on or plugged in. Do not stick your hands into the washer while it is running.
