How do you change the blades on a John Deere x300? In order to remove the old blades and install the new blades you'll need a wood block and a socket wrench. Install the wood block on an angle between the old mower blade and the mower deck to keep the blade from turning when you remove the nut.
Full Answer
How to level a deck on a John Deere X300?
- GXAL41983-UN-04MAR13 A convenient leveling gauge (A) (AM130907) is available from your dealer. ...
- GXAL41984-UN-04MAR13 Turn left blade (C) as shown. ...
- PY21325-UN-19AUG14 Adjust mower deck level, if necessary, by turning rear nuts (E) clockwise to raise the side of the mower deck, or counterclockwise to lower the mower deck.
How to install a John Deere snow blade?
- Rear weights and tire chains are recommended for additional traction.
- AM132109 rubber squeegee kit is recommended for better cleaning action and protection of smooth surfaces.
- LP33712 manual angling kit is recommended for the operator convenience of changing the blade angle from the tractor seat.
How to adjust idle on John Deere X300?
the idle stop screw needs to be *just* touching the throttle, if not the throttle will get sticky in the mornings the jag may self adjust but generally speaking most cars like the TPS to sit at ~0.5v at idle. if the tps reads 0v the ECU will assume a short to ground condition exists and throw a fault code.
How to install a John Deere snow blower?
You can install a John Deere snow blower by first making sure you have the proper tools. Place the snow blower attachment in front of the tractor. Turn the tractor on, and adjust the mower lift so that it is in the raised position. Pull the handle for the mower lift to raise it up, and turn the tractor off.
How do you remove a lawn mower blade without removing the deck?
1:427:38Change Your Riding Lawn Mower Blades Without Taking Off the DeckYouTubeStart of suggested clipEnd of suggested clipSo what I do is just set a little block of wood right here on the lip of the deck. And then put a CMoreSo what I do is just set a little block of wood right here on the lip of the deck. And then put a C clamp on it going underneath the deck. And what that's going to do is stop your blade from turning.
How do you take the blades off a John Deere riding lawn mower?
0:3813:38How to Change John Deere E100 Mower Blades and Remove DeckYouTubeStart of suggested clipEnd of suggested clipAnd actuates the blades underneath by pulling an idler pulley tight. So there are going to be a fewMoreAnd actuates the blades underneath by pulling an idler pulley tight. So there are going to be a few more steps with the manual pto than there normally would be with an electric.
Are John Deere mower blades reverse thread?
Are John Deere Mower Blades Threaded in Reverse? No. The bolt that holds John Deere mower blades in place is threaded in the usual fashion. To tighten it you simply turn it to the right, (clockwise) like you would any standard bolt.
How many blades does a John Deere X300 have?
3 Blades Required for 48" Cut.
What size are John Deere blade bolts?
John Deere Blade BoltSpecificationThread Size12.000 MMLength25.000 MMThread Length19.700 MMFlange Diameter26.600 MM6 more rows
How do you balance a John Deere lawn mower blade?
0:332:09How to Balance Mower Blades : Lawnmower Maintenance & RepairYouTubeStart of suggested clipEnd of suggested clipThe easiest way I think to do it is to just clamp a nail into a vise. Then you can set the blade onMoreThe easiest way I think to do it is to just clamp a nail into a vise. Then you can set the blade on the nail through the blade Center hole.
Which way do mower blade bolts turn?
The blades on many brands of walk-behind mowers rotate to the right, the clockwise direction, when you are mowing. To remove the blade, you must turn the blade's retaining bolt to the left, or counterclockwise.
Are lawn mower blade bolts left hand thread?
Some twin-blade mowers are both left-hand threaded and right-hand threaded. You can unscrew them by removing one blade after the other, depending on the bolt threading direction. Turn the left-hand thread retaining bolt to the left while the right-hand thread bolt to the right unscrew them.
How do you loosen a lawn mower blade nut?
2:434:17How to remove a stubborn mower blade nut - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So itMoreLike I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So it should loosen hopefully whoa there we went.
How much does a John Deere X300 cost brand new?
John Deere X300 Pricing Pricing on the 2021 John Deere X300 Series Lawn Tractors ranges from $3,199 to $6,399. They're available exclusively from John Deere dealers or through Deere.com. All of the X300 Series mowers come with a 4-year/300-hour bumper-to-bumper warranty.
What year is John Deere X300?
John Deere X300X300 Serial Numbers20060100012008085001200912000120101500014 more rows•Jul 6, 2021
What horsepower is a John Deere X300?
John Deere X300John Deere X300 Engine18.5HP Kawasaki 603cc 2-cyl gasolineFuel tank3.3 gal 12.5 LEngine details ...Mar 8, 2022
How Often Should You Change Your John Deere Mower Blades?
Your John Deere mower blades should be replaced with a new set of blades each year. I find it best to replace blades during your annual John Deere maintenance. That way it’s easy to keep track of how old your blades are.
How Often Should You Sharpen Your John Deere Mower Blades?
Sharpen your John Deere lawn mower blades after approximately every 25 hours of use. For the average homeowner, this amounts to about twice a year. You may need to sharpen them more often if you mow more than the average homeowner or if you mow in dry and dusty conditions.
Do New John Deere Mower Blades Need to be Sharpened?
New John Deere mower blades do not need to be sharpened. They have been sharpened during the manufacturing process and coated with a paint. There is no need to remove the paint along the edge of the blade. The new blade is ready to install and use on your mower.
Inspect Your John Deere Mower Blades for Damage
It is possible for your John Deere mower blades to become very worn or damaged from normal use. Check the condition of your mower blades regularly. Sharpen or replace them when they begin to appear dull, worn or damaged.
How to Safely Sharpen John Deere Lawn Mower Blades DIY
You can save some time and money by sharpening your own John Deere mower blades. There are several different tools that can be used to sharpen your blades including a metal file, drill powered blade sharpener or a disc grinder. Follow these steps to sharpen your blades:
Balance Your John Deere Mower Blades
It is necessary to make sure your John Deere mower blades are balanced after sharpening them. Unbalanced blades can cause excessive vibration, spindle damage and potential engine damage.
When You Should Seek a Professional Sharpening Service for Your John Deere
I can sharpen my mower blades myself and I even have the tools to do so, but I still choose to have my local lawn mower dealership sharpen my blades. The dealer does a much better job than I do and it’s convenient. I drop them off at the dealership and pick them up a couple days later.
How long does it take to remove John Deere blades?
Because the removal process is simple and you can do this by yourself. It approximately takes 20-30 minutes to complete the whole task.
How many blades does a John Deere lawn mower have?
Sometimes John Deere riding lawnmower carries two blades. If you have two blades in your lawnmower, then follow the same process to remove another blade from your mower.
What does it mean when a lawn mower blade is dull?
A dull and damaged blade is always a burden for any lawnmower owner. And when the blade of a mower becomes dull it isn’t able to serve its actual purpose. So, should do you carry dull or damaged blades?
How long does it take to remove a blade?
It approximately takes 20-30 minutes to complete the whole task. Before removing the blades, you need to manage some tools that will make the task convenient for you. Let’s have a look at the tools that you need to use for removing the blades.
Can you use a hydraulic jack to raise a lawn mower?
Basically I recommend you use a hydraulic jack to raise the mower. Because sometimes you need to remove the whole deck for removing and replacing the blades. It’s quite a tricky task to remove the deck and install it again. Using a hydraulic jack will really make your task easy and convenient.
Can you remove a John Deere mower blade?
Not at all. You should remove the blade and install a new one. However, when you use a John Deere lawnmower, it’s really worthless to carry the damaged blade. Because the removal process of a John Deere mower blade is simple and you can do it by yourself. I guess you have no idea how to remove John Deere mower blades.
