How do you change the blade on a MK 470 tile saw? Loosen the wing nut securing the blade guard. Loosen the blade guard retaining knob, then open the blade guard. Insert the shaft wrench onto the shaft, between the blade and body of the saw. Loosen, then remove, the retaining nut using the blade wrench.
What is the mk-470 saw?
The MK-470 is compact and lightweight, and incorporates features found on larger professional models. This saw is engineered as a self-contained unit consisting of a powerful universal motor, removable water reservoir and water recirculating system, and quality diamond blade.
How do I change the brushes on my Mk power tool?
The brushes are easily accessible by removing the brush caps with a flat end screw driver from the square top of the motor. Pull the brushes from their holder and change them when approximately 1/4" of the brush remains. Use only authorized MK parts.
What should I do if my diamond blade is bent?
Check for worn out diamond edge & resharpen as necessary using dressing stick (MK part #152792), and slowly cut stick in (10) 1/16” slices to redress the diamond blade edge. Check that blade is rotating in the same direction as the rotation arrow. Make sure the blade core is not bent.
How do I change the blade on my tile saw?
1:002:28How to Change / Remove a Diamond Blade on Wet Porcelain Tile Saw ...YouTubeStart of suggested clipEnd of suggested clipWrenches. Something like that that will fit around that nut right there and there's a small nutMoreWrenches. Something like that that will fit around that nut right there and there's a small nut right on. Top.
How do you change the blade on a MK 660 tile saw?
Mk Diamond Wet Saws MK660 2010 Blade ReplacementStep 1 Blade Cover. ... Unscrew the knob. ... Loosen the plastic knob holding the blade cover in place. ... Loosen the wing nut on the blade cover pivot shaft. ... Pivot the blade cover up and pull it off the shaft. ... Step 6 Blade. ... Remove the hex nut. ... Remove the cutting blade.
How do you change the blade on a MK 370 exp?
The MK Diamond MK-370 saw blade attaches to the saw using a single nut; you can quickly remove it using tools included with the saw packaging. Loosen, then remove, the retaining nut using the blade wrench. Remove the inner flange under the retaining nut.
Can you replace the blade on a tile cutter?
1:081:58How To Replace The Blade On A Tile Cutter - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd there's the old blade rate there and where I put new blade. In. And just hold it gently so youMoreAnd there's the old blade rate there and where I put new blade. In. And just hold it gently so you don't cut your fingers.
How do you use MK tile cutter?
2:454:55MK Diamond Medium and Large Tile Saws | The Home Depot RentalYouTubeStart of suggested clipEnd of suggested clipAnd the bottom of the cutting table for all cuts you'll place your hands on the backside of theMoreAnd the bottom of the cutting table for all cuts you'll place your hands on the backside of the cutting table hold the tile with your fingertips. And gently push it into the blade.
How do you remove a stuck wet saw blade?
0:496:08How to Remove a Stuck Circular Saw Blade - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you use an adjustable wrench or whatever size this is whatever you have usually circular sawsMoreAnd you use an adjustable wrench or whatever size this is whatever you have usually circular saws come with a wrench just like this. And you put it on here.
How do I know when to replace my tile saw blade?
How to know when to replace a tile saw bladeUnusual vibrations when the saw is turned on.Slow cutting speed when working on an easy material.Obvious signs of warping or damage.Unusual thumping noises when cutting.You can see the steel core of the blade because it has worn through.
How do you know when tile blade is bad?
Tough Cutting A good tile wet saw blade should cut steadily and quickly through any material, no matter how dense or hard. If you find that over time your cuts are going more slowly, or that you are exerting more and more pressure on the tile to get it through the blade, the blade probably needs to be replaced.
What is a MK 470 tile saw?
The MK-470 Tile Saw is a versatile cutting machine designed to use diamond blades. Its function is to cut a variety of materials to include ceramics and certain types of stone. The MK-470 is compact and lightweight, and incorporates features found on larger professional models. This saw is engineered as a self-contained unit consisting of a powerful universal motor, removable water reservoir and water recirculating system, and quality diamond blade. The motor operates on standard 120V current, and the water pump is conveniently energized by the motor. Motor The MK-470 features a powerful right angle drive universal motor with the following specifications: 115V 50/60Hz 1/2 Horsepower 5.3 AMP 5,500 RPM Maintenance free sealed pinion shaft and gear assembly The heavy-duty pinion shaft and gear assembly are permanently lubricated and sealed within the gear box. Cutting Head The 7 inch (178mm) blade capacity yields a depth of cut of 1-3/4". The hinged blade guard allows easy blade changes.
What to do if blade won't cut?
if blade won’t cut properlyCheck that the blade is the correct specification for material being cut. Check for worn out diamond edge & resharpen as necessary using dressing stick (MK part #152792), and slowly cut stick in (10) 1/16” slices to redress the diamond blade edge. Check that blade is rotating in the same direction as the rotation arrow. Make sure the blade core is not bent.
How to cut material with a blade guard?
Do not attempt to cut pieces too small to hold by hand outside the blade guard. Avoid awkward hand positions where a sudden slip could cause a hand or fingers to come in contact with the blade. When cutting any material, make sure it is fully supported. Hold workpiece firmly against the fence. Only feed the material as fast as the blade is able to affectively cut. DONOT FORCE THE MATERIAL INTO BLADE!
What is the scale on the conveyor table back stop?
The markings on the conveyor table back stop are used to aid in cutting tile to particular dimensions. The scale on the top of the back stop is used for setting the rip guide’s diamond window indicator relative to the exact distance from the diamond blade to the edge of the rip guide. You must first measure the tile for the cut to act as the standard, and then use the rip guide & table markings to assist in additional cuts.
How many amps does a tile saw draw?
The MK-470 tile saw is wired for 120V, single phase operation, and draws 5.3 amps at 120V. This is not a large load, however if the machine is operated on any circuit that is already close to its capacity, the circuit breaker may be tripped. If this occurs, eliminate other loads from the circuit. A separate circuit protected by a 20 amp breaker is ideal. If other loads do not exist and power failure still occurs, have the circuit inspected by a qualified electrician. If a generator is used, use one rated at 3.5Kw minimum. This tool must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. • Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician. • Improper connection of the equipment - grounding conductor can result in a risk of electric shock. The conductor with the insulation having an outer surface that is green, with or without yellow stripes, is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment - grounding conductor to a live terminal. • Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. • Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. • Repair or replace damaged or worn cord immediately. See Table 1 for proper extension cord gage requirements.
Where is the serial number on a saw?
please record the serial number (Located on the cover post casting ) of your saw in this block.
Can a MK 470 tile saw be damaged?
n o t i c e Your MK-470 Tile Saw or other pro p e r ty could be damaged if you don’t follow instru c t i o n s .
How do you change the blade on a MK 470 tile saw?
Loosen the wing nut securing the blade guard. Loosen the blade guard retaining knob, then open the blade guard. Insert the shaft wrench onto the shaft, between the blade and body of the saw. Loosen, then remove, the retaining nut using the blade wrench.
Why does my tile saw blade wobble?
Blade Wobbles Check for bad bearings, bent shaft, or worn mounting arbor.
When should I replace my diamond tile saw blade?
A good tile wet saw blade should cut steadily and quickly through any material, no matter how dense or hard. If you find that over time your cuts are going more slowly, or that you are exerting more and more pressure on the tile to get it through the blade, the blade probably needs to be replaced.
Can you sharpen a wet saw blade?
As the name implies, tile saw blades were designed to cut tile. The diamond grits on the edge of the blade have a tendency to wear down and glaze over when you ‘re cutting harder ceramic materials. Sharpening a tile saw blade requires making a slurry out of an abrasive material and the saw’s coolant or water.
How do you know when a diamond saw blade is dull?
You can tell that the diamond blade is either glazed or getting dull because the rate at which it can cut slows down. In other words, it starts cutting slower and slower. So if that’s the case you want to remove the glaze/sharpen it. If it is glazed or dull the technique is the same for either condition.
How do you remove a table saw blade without a wrench?
The open hand wrenches are also applicable for removing blade. So, if you own one, make use of it here. In case you lack one wrench meant to keep the blade in place, then simply use a wooden block. This will easily stop any sort of turning by wedging teeth so that you can use the only wrench for loosening arbor nut.
Can you put a wood cutting blade on a tile saw?
Though a wet tile saw may resemble a table saw, it is not designed to cut through wood. It is equipped with a diamond-edged, carbide blade that is different from that of a table saw. If used on wood, it would likely jam and/or ruin the blade itself, not to mention cause injury to the operator.
Why is my wet saw blade coming out of the plumb?
If the tray on the wet saw is gliding perfectly straight but your cuts are coming out of plumb, the blade may be warped, damaged or have loosened to the point it cannot be tightened anymore. If you have tried adjusting and tightening the blade but your cuts are still out of plumb, it's time to replace the blade.
Where to put shaft wrench on saw?
Insert the shaft wrench onto the shaft, between the blade and body of the saw.
How much does a wet saw cost?
Online retailers offer wet tile saws ranging from less than $100 to several hundred dollars. Unlike table saws, though, this is a one-use tool that you won't use except when you are tiling.
