Remove your mower blade and match it up to a new mower blade. Place the used blade on top of the new blade. If you find any bends and gaps between the two blades, replace your Kubota blade.
Full Answer
How do you replace the blade on a mower blade?
Use a socket wrench to remove the center nut. Pull the blade off the shaft and place the new blade onto the shaft. Thread the retaining nut onto the shaft with your fingers, wedge the block of wood between the blade and the deck and tighten the nut with the socket and ratchet.
How do you sharpen Kubota lawn mower blades?
Follow these steps to sharpen your blades: Put on your work gloves and safety glasses. Use a rag to clean the dirt off your mower blades. A wire brush can be used for stubborn areas of buildup. Securely place your Kubota blade in a vice to keep it from shifting during sharpening.
How do you get to the blades on a tractor?
The only better way of getting to the blades is to pull the tractor over a pit or put it on a car lift. Good Luck! BX 2360 here with a 60" mmm. I run the front up on car ramps, and use a sears craftsman 19.2 volt impact wrench.
How do you use a wire brush on a Kubota mower blade?
A wire brush can be used for stubborn areas of buildup. Securely place your Kubota blade in a vice to keep it from shifting during sharpening. After sharpening one side, you will flip the blade and secure in the vice while you sharpen the other side.
Are Kubota mower blades reverse thread?
No. According to the Cub Cadet website, the bolt holding the mower blade in place is threaded in the normal fashion. That is, turn it right (clockwise) to tighten it, and turn it left (counterclockwise) to loosen it.
How do you tighten the blades on a Kubota mower deck?
6:447:25How to Take the Blades Off of Kubota BX Decks - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your hold your blade. Take your wrench. You should never need an impact to tighten these upMoreTake your hold your blade. Take your wrench. You should never need an impact to tighten these up wrench or socket. That's with the ratchet works fine and just slowly tighten them up.
Which way do I turn the bolt to remove mower blades?
To remove the blade, you must turn the blade's retaining bolt to the left, or counterclockwise. Before undoing the blade, tip the mower on its side with the engine air cleaner facing up and block the blade with a piece of wood so it can't turn.
How do you remove a lawn mower blade without removing the deck?
0:357:38Change Your Riding Lawn Mower Blades Without Taking Off the DeckYouTubeStart of suggested clipEnd of suggested clipPlug. Just to make sure you don't have any accidental startups. All right so under the mower thereMorePlug. Just to make sure you don't have any accidental startups. All right so under the mower there is a nut right here and it is holding the blades onto.
Do lawn mower blades need to be aligned?
Aligning the Blades If you have a manufacturer's manual, read it first. The problem could be related to the tire pressure, which can throw off the weight of the mower deck. Some mower manuals, like this one from John Deere, make a point of saying that mower blades need to be aligned perpendicular to one another.
How do you remove a Kubota zero turn mower deck?
4:0115:10Removing Zero Turn Lawnmower Deck - - YouTubeYouTubeStart of suggested clipEnd of suggested clipTwo things to point out here one have a board handy to help you release the tension.MoreTwo things to point out here one have a board handy to help you release the tension.
How do you loosen a nut on a lawn mower blade?
Tilt the mower on its side so that the side of the engine with the air cleaner faces upward. Push a wooden wedge or block between one of the blade tips and the mower housing to prevent the blade from turning counterclockwise when you loosen the bolt.
Does a lawn mower blade spin clockwise or counterclockwise?
Since most lawnmower blades turn clockwise, the bolt often goes counter-clockwise. To check the mower's bolt, you have to turn it off, remove the spark plugs, and lay the lawnmower on its side. The bolt sits in the middle of the blades.
How do you remove a stubborn lawn mower blade?
2:434:17How to remove a stubborn mower blade nut - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So itMoreLike I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So it should loosen hopefully whoa there we went.
How do you change a lawnmower blade?
0:263:31HOW TO CHANGE LAWN MOWER BLADES - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo all you have to do is go into a mold shop and tell them which law may have and they'll supply youMoreSo all you have to do is go into a mold shop and tell them which law may have and they'll supply you with the right ones so how do we get to these blades.
How do you install a lawnmower blade?
0:352:07How to determine which side of Cutting Blade to attach ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnother method you can use to find out which side of the blade you should mount to the crankshaft isMoreAnother method you can use to find out which side of the blade you should mount to the crankshaft is to find the edge of the blade that's opposite the sharpened side or sharpened edge of the blade.
What size is the nut on a lawn mower blade?
What size are the tractor cutting blade retainer nuts and what direction should they be turned? The retainer nut on most of our riding mower blades are a 5/8" thread diameter. This sized thread diameter nut normally requires a 15/16" wrench or socket tool in order to remove/install.
How Often Should You Change Your Kubota Lawn Mower Blades?
Mower blades on your Kubota lawn mower should be changed once a year. Blades that wear quickly because they are exposed to excessive dirt, rocks and gravel will need to be replaced more frequently.
How Often Should You Sharpen Your Kubota Lawn Mower Blades?
Sharpen your Kubota mower blades after every 25 hours of use. For the average homeowner, this amounts to twice a year. When operating your mower in sandy conditions, you will need to check your mower blades and sharpen them more frequently.
Do New Kubota Mower Blades Need to Be Sharpened?
A new Kubota mower blade does not need to be sharpened before it is installed on your mower. The blade is sharpened during the manufacturing process and coated with a paint. This paint will wear off the edge of your blade while mowing.
Check Your Kubota Mower Blade for Excessive Wearing and Damage
A bad mower blade can affect your cut quality. There are several items you need to watch out for when inspecting your mower blades for wearing and damage. If you are experiencing a bad or uneven cut with your Kubota, check out my article on items that can cause your Kubota to give you an uneven cut.
Items That Can Prematurely Wear & Damage Your Kubota Mower Blade
It is good practice to walk your yard prior to mowing to remove any items that can cause damage to your mower deck and blades. There are several items that can prematurely wear or damage your Kubota blades:
How to Sharpen Your Kubota Mower Blades DIY
You can save some time and money by sharpening your own Kubota mower blades. There are several different tools that can be used to sharpen your blades including a metal file, drill powered blade sharpener or a disc grinder. Follow these steps to sharpen your blades:
How to Balance Your Kubota Mower Blades
It is essential to balance your mower blades before placing them on your Kubota mower. Failing to do so can damage your spindle bearings and cause a severe vibration. A balanced blade is a blade that has equal weight on each side of the blade. Use a blade balancer to check for equal weight.
What direction do blade retention bolts loosen?
Blade retention bolts normally loosen in the direction the blade turns. For exaple, the blades on my Woods L59 that rotates CCW (when viewed from above) are left hand threads. A good impact wrench is required to break the bolts loose, without holding the blades. Robert.
How to take pictures of a tractor deck?
The easy way is to take pictures of the deck on the tractor including all of the linkages and then remove the deck and flip it over and the blades are exposed and using a impact gun and air compressor spin the nuts-bolts off with the gun . The hard way is to jack the tractor up and then get it high enough to reach under and try to wrench ...
