How to replace waterpump step 1. drain cooling system. step 2. remove battery and battery tray. step 3. remove drive belt. step 4. remove water pump bolts (318).
What causes a water pump to go bad on a Chevy Impala?
Here are some of the most common problems that can lead to a bad water pump: Your Impala’s water pump is designed to rotate with coolant inside of it. This helps create a watertight seal that can withstand the pressure in the cooling system. Without water the fluid cushion between the two rings (shaft and stationary) is lost.
How do I know if my water pump is bad?
If your water pump is easy to reach, you can gently place a really long screwdriver tip against it. Then, place the handle end of the screwdriver against your ear. You should be able to hear the noise clearly coming from the water pump.
What happens if the water pump does not pump water?
If it doesn’t pump water through the engine, it’s going to overheat and do a lot of damage. Typical signs of a bad water pump include overheating, white smoke, a bad smell, rough idle, and more. A water pump works by pumping water through the engine.
Can a serpentine belt cause a water pump to go bad?
The serpentine belt can cause the water pump to go bad if it’s been improperly installed, or if there’s too much tension on it. Here are some common signs that a serpentine belt is bad. A bad water pump has the potential to cause a lot of engine damage.
How do you put a water pump on a 2006 Chevy Impala?
1:383:48How to Install a Water Pump: 2011-06 Chevy Impala LS, LT, LTZ 3.5L, 3.9 ...YouTubeStart of suggested clipEnd of suggested clipRemove the five water pump retaining bolt. And remove the water pump. Remove the water pump gasketMoreRemove the five water pump retaining bolt. And remove the water pump. Remove the water pump gasket and clean the gasket surface.
How much does it cost to replace a water pump on a Chevy Impala?
Chevrolet Impala Water Pump Replacement Cost Estimate. The average cost for a Chevrolet Impala water pump replacement is between $681 and $805. Labor costs are estimated between $153 and $193 while parts are priced between $528 and $612.
How do you change a water pump on a Chevy Impala?
2:3713:29How To Replace a Water Pump and Save $783 - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo grab a wrench and get it on the bolt of the tensioner pulley. And pull downwards to relieve theMoreSo grab a wrench and get it on the bolt of the tensioner pulley. And pull downwards to relieve the tension of the belt. And now we can easily get the belt off the pulleys. So it's out of our way.
How much is a water pump for a 2006 Chevy Impala?
Taking all these points into consideration, you can expect to pay anywhere from $375 to $787 (including parts and labor). Of course, shopping around to get a few quotes is your best bet to get the best deal.
Can you replace a water pump yourself?
A specialist workshop usually estimates a good three hours of work for changing a water pump. However, if you do this work yourself, the only costs incurred are those for a new water pump. These are usually between 50 and 500 pounds.
Where is the water pump located on a 2006 Chevy Impala?
1:0714:30Water Pump - 2006-2013 3.5L Chevy Impala - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo Chris do you need to drain all the coolant not necessarily on this car the water pump is aboutMoreSo Chris do you need to drain all the coolant not necessarily on this car the water pump is about halfway up the engine block.
How many hours does it take to replace a water pump?
Fixing a broken water pump can take anywhere from two hours to most of a day. A simple replacement should take around two hours, but more complicated work trying to fix a water pump (which will save you money on parts) can take four or more hours.
How long does it take to remove and replace a water pump?
On average, water pump replacement is a 3 hour job. You may pay less if you buy the pump yourself and give it to the mechanic to install, though use caution and make sure to buy the parts from a reputable source. Make and model of vehicle can have a significant effect on total cost.
What are the symptoms of a bad water pump in a car?
Five Signs Your Water Pump Is FailingOverheating. A dead or dying water pump cannot circulate coolant through your vehicle's engine and, as such, the engine will overheat. ... Coolant Leaks. Coolant leaks from the water pump are common and a clear sign that it's time to replace the pump. ... Corroded Water Pump. ... Whining Noises.
Why is my 2011 Chevy Impala overheating?
The most common reasons a Chevrolet Impala is overheating are a coolant leak (water pump, radiator, hose etc.), the radiator fan, or a failed thermostat.
How do you change a water pump on a 2000 Chevy Impala?
3:4516:18How to Replace Engine Water Pump 00-05 Chevy Impala - YouTubeYouTubeStart of suggested clipEnd of suggested clipI just pull the pump forward to expose that water pump bolt. Okay so now you see I have to removeMoreI just pull the pump forward to expose that water pump bolt. Okay so now you see I have to remove those two bolts my power steering pumps out of the way. Easy access to that bolt and the rest of them.