How do you change a ball joint on a Ford Ranger? Lift the upper control arm out of the spindle assembly. Remove the nut holding the lower ball joint in place. Mount the spindle on the lower ball joint.
How do you replace a ball joint on a steering wheel?
Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included.
How do you replace a ball joint on a lower control arm?
If your vehicle uses pressed-in ball joints, you’ll need to remove the lower control arm and take the assembly to a mechanic with a hydraulic press to swap the joints out. Slide the new joint into place and pump it full of grease.
How do I replace a broken ball joint?
Purchase the correct replacement ball joint assembly for your vehicle. Go to the auto parts store and get a replacement part appropriate for your make and model. All you've got to know is the type of vehicle and you should be able to use the guidebook in the aisle, or ask for help and they'll be able to direct you.
Does replacing a ball joint affect alignment?
Replacing a ball joint can affect alignment. If a ball joint is worn enough, and the vehicle was previously aligned, it might be wise have the vehicle realigned. Include your email address to get a message when this question is answered. Video . By using this service, some information may be shared with YouTube. Consider ball joints as a set.
How do you remove the ball joints on a Ford Ranger?
3:2818:50How to REPLACE Lower BALL JOINT on a FORD RANGER - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing you can always try is just tapping the stud. A little bit with a hammer because in thisMoreFirst thing you can always try is just tapping the stud. A little bit with a hammer because in this case with the lower ball joint you do have gravity on your side.
How do you change the upper ball joint on a Ford Ranger?
2:1015:46How to change ball joints on a Ford Ranger - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you want to have the vehicle supported on the lower control arm so we'll take the upper bolt outMoreAnd you want to have the vehicle supported on the lower control arm so we'll take the upper bolt out this is a 15 millimeter. And slide the slide the bolt out you might have to gear.
Can I replace my ball joints myself?
Ball joints are not always an easy replacement, but a DIYer who is versed in changing suspension and brake components will probably be able to tackle the job.
How easy is it to replace a ball joint?
Ball joint replacement is not straightforward, as they can be very tricky to access and install – especially with age and rust. On some cars, the ball joint is integrated into the control arm. If you're not familiar with the suspension and wheel assembly, it's best to visit a garage for a professional check.
How do you replace upper and lower ball joints?
2:494:56How To: Replace Ball Joints on Your Vehicle - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress slip the appropriate press tube around the bottom of the ball joint under the control arm thenMorePress slip the appropriate press tube around the bottom of the ball joint under the control arm then use the clamp. And a ratchet and socket to push the ball joint. Out.
How long do ball joints last Ford Ranger?
Most ball joints will last for 100,000 miles or more. Rough driving habits may shorten the life of these parts.
How do you remove a ball joint without a press?
0:146:10How to remove and install ball joints without a press using only a floor ...YouTubeStart of suggested clipEnd of suggested clipGet your pail itself a piece of wood. So it doesn't slip off of there and then put your jackMoreGet your pail itself a piece of wood. So it doesn't slip off of there and then put your jack underneath. Directly underneath where the ball joint goes down and apply.
Can you replace just the ball joint without replacing control arm?
In order to know if just the ball joint or the whole complete lower control arm needs replaced, the lower ball joint will need to be disconnected from the steering knuckle and checked to see if it fits tight in the lower control arm. If it is loose, then replace control arm.
What tools do I need to replace ball joints?
What tools will I need for a press-in ball joint replacement?Ball joint press kit (including C-clamp and adapters)Socket, ratchet, torque, and extension wrenches.Socket air tools.Ball joint separator (also known as a pickle fork)Needle nose pliers.Screwdrivers.Tire iron.Side cutters.More items...•
Should I replace upper and lower ball joints at the same time?
A: Plenty of mechanics will recommend that you replace both the upper and lower ball joints at the same time. They may also recommend checking related components at the same time, such as the stud hole in the steering knuckle.
How much should a ball joint replacement cost?
Average Ball Joint Replacement Cost You can expect to pay around $300 in most cases, including both parts and labor. Most ball joints cost about $100 to $150, while the labor costs will run you $150 to $200. An independent repair shop will almost always be cheaper than the dealership as well.
What happens if a ball joint breaks while driving?
A worn ball joint is not a problem that should be put off—a catastrophic failure of any ball joint will result in your front suspension coming apart and causing loss of control of your vehicle.
How to install a receiver joint?
Follow the directions, and its pretty easy. You start with the lower one. Set the receiver cup to let the press push the joint out. another view. do the same with the upper, running the screw through the hole left by the lower one. Installation is similar to removal, but you use a smaller cup to press the new joint in.
How to get a spindle off easier?
Apply anti-seize to the back of the spindle and the bore on the knuckle (AFTER you do the joints!). This will make the spindle come off easier later.
Why do you want joints to be in phase?
You want the joints to be in “phase” with each other so they don’t bind and break. (they do anyway!)
What is passenger side shaft?
Passenger Side (long) shaft. This is a close up of the bore in the knuckle. You need to remove the upper and lower bolt attaching the ball joint. Now you need to use a pickle fork for the ball joint, or a lot of hammering. Take your pick.
How to install a new ball joint on a car?
Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from.
How to loosen a ball joint?
Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint. Sometimes, it's helpful to heat particularly corroded components with a torch to try to loosen them. Be careful if you try this.
How to remove a McPherson strut?
1. Pull the cotter pin and loosen the large castellated nut. The top should look like a crown, or castle, at the bottom. Leave the castellated nut in place, just a few turns in to keep it in a safe place. If you’re working on a McPherson strut suspension remove the “pinch bolt” that clamps the ball joint stud.
How to check if a ball joint is strut style?
Figure out if your vehicle's got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.
How to remove pressed in ball joint?
If your auto’s suspension uses pressed-in ball joints, you’ll need to remove the lower control arm and take the assembly to a mechanic with a hydraulic press, who can press the old ball joint out and the new ball joint in.
What happens if you wear out a ball joint?
A worn-out ball joint will pivot horizontally and vertically, negatively affecting your handling at low speed, and becoming especially dangerous at high speeds. Recognizable for a knocking sound in the wheel well as you execute a turn, fixing old ball joints is an important part of keeping your vehicle road-safe. You can do it yourself for the price of the parts and the right approach.
How to get ball joint out of steering knuckle?
It can be somewhat difficult because of the extremely tight fit which helps hold the ball joint in place and the road grime built up around the suspension, so you will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver.
