- Turn the pool filter system off.
- Attach your pool hose to the backwash port on your sand filter.
- Select the “Backwash” position on your multiport valve handle.
- Turn the pool filter system on and allow it to rush out of the backwash port and through the backwash hose for two minutes or so until the water ...
- Turn the filter off again and set your multiport filter valve to the “Rinse” position.
- Turn the pool filter system back on and allow it to run for a minute or so.
- Turn the pool pump off and switch the multiport valve to its original setting (usually the “Filter” position).
How do I backwash my pool sand filter?
How to backwash your pool sand filter. 1 1. Turn the pool filter system off. 2 2. Attach your pool hose to the backwash port on your sand filter. 3 3. Select the “Backwash” position on your multiport valve handle. 4 6. Turn the pool filter system back on and allow it to run for a minute or so. 5 7.
How long does it take to backwash a pool filter?
This normally takes between 1 minute and 3 minutes, depending on how dirty the filter was. Do you rinse after backwashing a pool? Once I have turned the pump off I always turn the multiport valve to Rinse and run the pump again for between 30 seconds and a minute.
How do you clean the filter on a multi port pool?
Turn the pool filter system on and allow it to rush out of the backwash port and through the backwash hose for two minutes or so until the water in the sight glass runs clear. Turn the filter off again and set your multiport filter valve to the “Rinse” position.
Why do I need to backwash my sand filter?
This backwash sand filter guide assumes that the filter needs to be backwashed because you have too much back pressure, too little suction or that you have just cleaned the pool which was dirty.
Can you backwash an Intex pool filter?
0:012:32How to backwash and clean intex pool sand filter. Easy! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll right this is how to backwash and clean your above ground pool sand filter intex uh your mainMoreAll right this is how to backwash and clean your above ground pool sand filter intex uh your main ones are filter recirculate a little bit uh backwash.
How often do you backwash an Intex sand filter?
0:514:35How Often Do You Need To Backwash my Above Ground PoolYouTubeStart of suggested clipEnd of suggested clipJust do it once a week whether.MoreJust do it once a week whether.
What is the proper way to backwash a sand filter?
0:472:39How To: Backwash a Pool Sand Filter - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor maximum safety turn off the power at the circuit breaker to the pump your pool filter valve isMoreFor maximum safety turn off the power at the circuit breaker to the pump your pool filter valve is probably at the filter setting for normal operation depress the multi-port valve handle.
Do you turn the pump on when you backwash?
Turn the Pump Back On Run your pump on the backwash setting for two minutes. While waiting two minutes on the backwash setting is standard, you can also determine if your filter is clean by watching the sight glass. Once the water flowing through the sight glass is clear, you will know your filter is clean.
How do you attach a backwash hose to an Intex sand filter?
0:001:01How to Attach a Backwash Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext wrap a filter fitting with teflon tape to create a better seal thread the fitting into theMoreNext wrap a filter fitting with teflon tape to create a better seal thread the fitting into the filter's waste port attach the backwash hose to the fitting.
How long do you need to backwash a sand filter?
Set the sand filter multi port valve handle to the BACKWASH position and ensure the handle locks in place. Turn on the pump and allow the sand filter to backwash for 2-3 minutes or until the water in the sight glass (typically located on the top of the filter) is visibly clear.
Where does the water go when you backwash a pool?
Simply put, when you backwash your pool filter, you reverse the direction of the water flow, and water moves back through the pool filter and out the waste or drain port. Just make sure you're disposing of it properly—and we'll get to that soon.
What happens if you don't backwash your pool filter?
Water flow – debris and contaminants clogging the filter media restricts the rate at which water can pass through the filter, reducing the flow of water into your pool. Water clarity – cloudy water may indicate that the filter media is dirty or unable to catch the dirt and debris making its way into your pool.
What happens if you don't rinse after backwash?
Then you rinse to help settle the sand and flush the last bit of crud and dust down the drain not back into your pool. if you don't rinse you will see cloudy water coming out of the jets for the first 30 seconds or so when u turn the filter back on.
Should sand come out when I backwash?
Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs. In general, you shouldn't be losing sand from your sand filter. Nor should any sand be coming out during backwashing, rinsing or filtering.
How do you backwash an above ground sand filter?
1:524:26How to Backwash Your Above-Ground Swimming PoolYouTubeStart of suggested clipEnd of suggested clipYou're gonna hear some water start to flow through the line. We're gonna go ahead and turn the pumpMoreYou're gonna hear some water start to flow through the line. We're gonna go ahead and turn the pump back on after it is locked securely in the backwash. Setting.
How do you use the waste setting on a sand filter?
0:313:23How To Use Different Pool Filter Valve Settings - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr debris in the bottom of the pool you didn't want it to go into the filter sand you can bypass theMoreOr debris in the bottom of the pool you didn't want it to go into the filter sand you can bypass the filter in the Google rate through and out of the waste outlet on your filter.
How Often Should You Backwash Your Pool?
The pool sand filter keeps your pool water clear, clean and safe. It does so by trapping the dirt & debris, when the pump pushes the pool water through the sand in the filter. Over time the sand gets dirty and less effective. You have to clean the sand by backwashing. But how often should you backwash your pool sand filter?
How Many Times a Month Should You Backwash a Pool?
The time to backwash your pool sand filter depends on the pressure reading. It is not necessary to backwash it at a fixed interval. Backwashing a pool sand filter, when it is not required, will waste pool water and expensive pool chemicals along with it.
How Long Should You Backwash Your Pool?
To backwash a pool sand filter, turn off the pool pump first. Position the valve handle to BACKWASH and turn on the pump.
Can You Backwash Your Pool Too Much?
Actually, you can if you follow a fixed time schedule, instead of backwashing based on the pressure reading.
Recommended Pool Sand Filters
The Hayward Pro Series Sand Filter for in-ground swimming pools will provide you with hassle-free, effective filtration. The weather-proof tank is constructed of a tough, color-fast polymeric material.
What happens when you backwash a pool sand filter?
When you backwash a pool sand filter, you are reversing the flow of water through the filter. The water passes through the filter from the bottom, rather than from the top, and dislodges all the dirt particles lodged in the sand . The dirt is then expelled, either to the sewer or the yard/garden, depending on the set up.
Why do pool filters need to be backwashed?
This guide assumes that the filter needs to be backwashed because you have too much back pressure, too little suction or that you have just cleaned the pool which was dirty.
Why does my pool filter lose suction?
This can happen, particularly if the pool is quite dirty, as the filter may become blocked which then builds up back pressure and reduces suction .
Why do you empty a pool in stages?
In this case it may be better to empty the pool in stages to allow the water time to soak in and distribute.
Why does my pool sand get blocked?
This also occurs because the sand becomes blocked by the debris that has been collected in the filter. you have just vacuumed the pool, which was particularly dirty and it is good practice to do it then as part of your regular cleaning routine.
Can you vacuum a pool with a backwash valve?
No, you cannot vacuum a pool when the multiport valve is in the backwash setting. This is because the water flow is reversed with the water from the pool (or the vacuum hose if it is connected) going from the bottom of the sand filter to the top and then into the waste pipework. Any dirt you pick up while vacuuming is likely to get trapped in ...
Can you leave the pool pump running after vacuuming?
If you haven’t already done this after vacuuming the pool, then turn off the pool pump. You should do this every time before you change the setting on the multiport valve as it you do not and leave the pump running it could damage the system.
