- Measure the garage ceiling surface you will be applying the plywood to. ...
- Use a stud finder to find the ceiling joists, then mark their locations with a pencil. ...
- Now you are going to glue your plywood in place using panel adhesive. Remember to apply the adhesive using zig-zag patterns.
- You need to use constructive adhesive on the back of the wooden molding (pre-cut). ...
- You should then use a putty knife to add a little putty to each nail hole, filling them in. ...
- You now need to stain the ceiling, but put down a drop cloth before starting. ...
Full Answer
Can I add a plywood ceiling to my garage?
To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience. Adding a plywood ceiling to your garage can make the space more appealing.
How do you attach plywood to a corner of a ceiling?
Lift the plywood to the ceiling using a drywall lift. Place it perpendicular across the joists. Push it into the corner, tight against the wall. Shoot 1½-inch staples, spaced 12 inches apart, through the plywood into each joist and on the blocking if applicable.
How do you attach plywood to a garage door joist?
Measure your plywood so that one edge fits on the joist above the garage door and extends to the furthest possible joist without running beyond the center of it. Mark the plywood to the correct size.
How can I prevent my plywood ceiling from sagging?
Screwing down the plywood to the joists will prevent your plywood ceiling from sagging and offer a professional looking surface to paint or texture if you like.
How do you attach plywood to a ceiling?
4:396:07Fitting 8x4 sheets of plywood to a Workshop ceiling - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then just get some screws in there you go become a cold but it. Works just be careful didn't IMoreAnd then just get some screws in there you go become a cold but it. Works just be careful didn't I like that they don't slip not the widget inside you don't need dropping on your head.
How do you install a 4x8 plywood ceiling?
0:003:20Laying Plywood for the Front Porch Ceiling - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe'll run through in this direction. I'm good there okay that's our starting point. Okay. How areMoreWe'll run through in this direction. I'm good there okay that's our starting point. Okay. How are you down there I'm good right on the line right there yeah okay Oh ready for another sheet.
Does plywood go on a ceiling?
You can add plywood to your ceiling without worrying about its weight. You don't need to use any additional support just to install it. The material is also much more workable than hardwood. You can cut a sheet of plywood into different sizes without using any special tools.
How do you attach OSB to ceiling?
2:1612:04Install OSB on a Shop Ceiling & LED Lights - Workshop Build SeriesYouTubeStart of suggested clipEnd of suggested clipThis is the first panel going up on the west side of the beam. Against the far north wall i tackedMoreThis is the first panel going up on the west side of the beam. Against the far north wall i tacked on some two by fours to help hold the edge of the ceiling. Panel.
Can you use plywood for a garage ceiling?
Drywall and plywood are two extremely common materials to use for a garage ceiling. Both can provide great looks and help tie together the whole garage, but each one has some utility benefits over the other.
How do you hang plywood?
2:2517:11Installing PLYWOOD WALLS (instead of DRYWALL) in the Not So Tiny ...YouTubeStart of suggested clipEnd of suggested clipAir sealed the panels to the framing. And typically with a wall covering like drywall the taping.MoreAir sealed the panels to the framing. And typically with a wall covering like drywall the taping.
What can I use for garage ceiling?
Which Material is Most Suitable for the Garage Ceiling?Aluminum Soffit. Making the best garage ceiling requires the best of materials. ... Vinyl Beadboard Soffit. This is an alternative for aluminum soffit. ... Corrugated Metals. ... Plywood. ... Oriented Strand Board (OSB) ... Vinyl Siding. ... PVC Tiles. ... Drywall.
How do you make a plywood ceiling look good?
0:589:04Plywood Faux Plank Ceiling - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe good side of the plywood is facing. Out up in my studio. I use my stud finder to mark theMoreThe good side of the plywood is facing. Out up in my studio. I use my stud finder to mark the location of the studs on the top and bottom of the slanted. Ceiling then used a straightedge to connect.
How do you cover seams in plywood ceiling?
Sand down the plywood, particularly around the edges where the pieces meet at the seams. Go over the entire surface with medium-grade sandpaper in a circular motion. Continue until all of the seams have been sanded down and the surface is smooth throughout.
Do you nail or screw OSB board?
A hammer and 8d nails are standard for installing OSB, but you can speed up the installation by using a nail gun. The caveat when using a nail gun is to set the depth of the nail so the head just dimples the surface of the OSB.
How do you hang OSB in a garage?
2:454:52OSB Interior Garage Walls - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you gotta scribe lines we're doing long straight cuts by hand with the seesaw. And then we'reMoreSo you gotta scribe lines we're doing long straight cuts by hand with the seesaw. And then we're drilling corners. And using the jigsaw to cut out the little boxes for the outlets and switches.
Can I use OSB for garage ceiling?
Both OSB and Sheetrock can be used to cover the walls in a garage. Fire-Rated OSB and sheetrock each meet the fire code requirements for attached and unattached garage spaces.
How big is plywood?
Our plywood sheets were 4 ft x 8 ft. And our trusses were on 2 ft centers. So we tried to lay things out in a way that would both look aesthetically pleasing, but also allow us to cut as few sheets as possible and still keep our plywood centered on the trusses.
How to cut a light box?
For the light boxes, we held the sheet up where it needed to go, then marked around the light box where to cut with a pencil. Then, we brought it back down and used a jig saw to cut that part out.
Why do we use staples in the center of sheets?
But there wouldn’t be any trim in the center of the sheets. So for that, we used long staples because they are less noticeable.
Can you use scrap 2x4s to attach a ceiling?
In those cases, we used some scrap 2x4s to add some bracing to attach the ceiling to. You can see below in the hole above the sink I screwed some pieces into the existing framing to attach the plywood to here.
Should I paint trim before installing?
I highly recommend painting all the trim before installing it. I painted some, but not all and it was a nightmare touching up all the little edges.
Can you cut plywood as little as possible?
You can pick a starting point however you want…just kind of sketch or plan it out so you waste as little plywood and cut as little plywood as possible.
Can you use a stud finder to screw plywood?
So it was easy to see where to put the screws to attach the plywood. BUT, if your ceiling is already finished with drywall, you can use a stud finder to find the joists or trusses and mark them on the drywall to screw the plywood into. . OR remove the old drywall and start clean.
How to measure plywood for a wall?
The ends of two adjoining pieces of plywood must center on a joist. Use a table saw to cut the plywood to the measurement.
How to sand plywood edges?
Sand the edges lightly with a hand block and 100-grit sandpaper to remove splinters, high spots, debris, chips or irregularities -- but don't sand dips in the edges. Check the thickness along the edges. Issues associated with plywood can include uneven seams due to irregularities in manufacturing. If you notice irregularities in the thickness, mark it. Use the irregular edge against a wall.
What is the most affordable type of plywood?
Fir is the most affordable type of plywood. Image Credit: photos777/iStock/Getty Images. Plywood is viable as a ceiling material, particularly in the basement. Plywood allows easier access to pipes, ducts and wiring than drywall. Plywood serves capably as ceiling material in garages, shops and rec rooms when aesthetic design is not an issue.
Can you use a drywall lift to lift plywood?
Use it to save money. A drywall lift will help you maneuver plywood sheets into place, but thin plywood is relatively light and can be lifted into place with the help of an assistant if you prefer. Warning. Wear eye protection at all times when working.
How to store plywood sheets in garage?
Section off a 4 by 8 ft (1.2 by 2.4 m) section of your garage floor. To protect your plywood sheets from warping, the best way to store them is by laying them flat.
How to store plywood?
1. Lean the plywood against an interior wall if you can. The easiest way to store plywood is just to lean it against a wall. However, this can lead to the plywood bending or warping, so it’s not recommended for long-term storage. If you store your plywood against an outside wall, moisture may seep through the wall and cause ...
How to build a raised platform?
Create a raised platform by laying pieces of lumber about 2 feet apart, then stack the plywood on top of the platform. If you don’t have the floor space to store your plywood laying flat, purchase or build a hanging rack large enough to hold several sheets of plywood. Keep reading to learn how to store plywood vertically!
How to protect plywood from moisture?
Attach a piece of scrap plywood to the bottom of the rack to protect the plywood from moisture seeping in through the floor. If you build your own storage rack, the possibilities for customizing it are endless. You can choose whether to store the plywood on its end or rest it on its side.
How to build a vertical plywood rack?
You can build a basic storage rack by creating a 4 by 8 ft (1.2 by 2.4 m) frame out of lumber. Place a support beam at each end of the rack and one in the middle to hold the plywood in place. Attach a piece of scrap plywood to the bottom of the rack to protect the plywood from moisture seeping in through the floor.
How to keep plywood from rotting?
Use lumber to create a base that will keep the plywood off the ground. Moisture can seep up through the earth, causing your plywood to rot. You can use any size lumber you have, as long as it creates a frame that is big enough to contain the plywood. Space your lumber about 2 feet (0.61 m) apart to ensure it’s supported enough that it doesn’t sag.
How much weight can a ceiling beam hold?
Most ceiling beams can safely support about 160 pounds (73 kg). This means you can safely store 3 sheets of 1⁄2 in (1.3 cm) thick plywood, or 2 sheets if they are 5⁄8 in (1.6 cm) thick.
How Far Apart Should Screws and Nails Be in Plywood?
Generally, nails and screws should be spaced six inches on center along the plywood panels edges, and twelve inches on the studs or joists on the interior of the panel. On flooring, you may want to space them even more closely for extra stability. Also make sure your installing your plywood correctly, take a look at my article What’s the Correct Direction for Installing Plywood? to be sure your not making these mistakes.
What Nails Do You Use for Plywood?
Different types of nails can be used, depending on what you are doing with the plywood. The lengths of the nails are determined by the material underneath the plywood.
Will Finishing Nails Hold Plywood?
While they will hold plywood, be sure to get the heavier type. Another problem with finishing nails is that they have a small head, which can eventually allow the plywood to pull up.
Can I Use Screws for Roof Sheathing?
While most people prefer nails for roof sheathing, screws can be used to attach plywood sheathing, but you’ll need to ask your supplier about the size you need. The thickness of the plywood used (usually a 2 ½ inch for roof sheathing), along with the local weather will help determine what size screws to use.
Can I Use Drywall Screws on Plywood?
Just about any source that can be found on the subject will tell you not to use drywall screws on plywood. There are separate drywall and wood screws for a reason. Drywall screws were developed originally to provide a rapid method of attaching drywall to metal studs when installing it in commercial buildings. They were designed for speed economy.
How to store nails and screws?
Storage – You can store a few leftover nails, screws, or nuts and bolts in old prescription bottles. Scraping off the label will help you see what’s inside. This is much better than dropping them into a jar with the different sizes and types all mixed up. Sandwich bags will also work, but screws and nails do tend to punch through these thin bags.
Can I Use Brad Nails for Plywood?
Brad nails are actually made from 18-gauge steel wire. The small diameter makes them easier to use, but many people just use them to hold glued pieces together until the glue dries. Since they also have a smaller head, they are often used in furniture, paneling or other interior work where it is desirable to make the nails less visible. Since these nails are thin, they work well with plywood.
