How do you apply Henry Tropi cool roof coating?
- STEP 1: CLEAN THE SURFACE.
- STEP 2: REPAIR & REINFORCE.
- STEP 3: APPLY COOL ROOF COATING. On a clear, warm, sunny day (65 F and rising), apply Elastomeric Roof Coating to a dry roof surface. Cut in along ...
What is Tropi cool roof coating?
Henry® 887 Tropi-Cool® 100% Silicone White Roof Coating is a premium, 100% silicone, moisture-cure coating designed to reflect the sun's heat and UV rays as well as protect many types of roofs.
How do you apply cool roof coatings?
There are three simple steps for applying cool roof coatings: Thoroughly clean the roof surface. Repair and seal roof penetrations, tears, open seams, etc. using Elastek 103 Crack & Joint Sealant and reinforce with polyester roof fabric as necessary. Apply coating when the roof is dry and the sealant has set.
Is Tropi cool a registered trademark of Henry?
® Henry and Tropi-Cool are registered trademarks of Henry Company LIFETIME WARRANTY How to Restore Your Roof: Using a pressure washer or high pressure nozzle on hose, use appropriate pressure to wash the roof with non-filming detergent, such as TSP or TSP substitute.
Where can I get a roof restoration from Henry company?
A system approach for RV, trailer, and mobile home roof restoration and weatherproofing from the #1 Choice of Professionals.® Henry Company 999 N. Sepulveda Blvd., Ste 800 El Segundo, CA 90245 800-486-1278 [email protected] www.henry.com
How do you apply Henry roofing coating?
1:113:06Use a stiff bristle brush or broom with. Additional water and detergent to remove any stubborn dirtMoreUse a stiff bristle brush or broom with. Additional water and detergent to remove any stubborn dirt grease algae or moss. Give the roof of final rinse and allow the roof to dry completely.
How do you apply cool roof coating?
There are three simple steps for applying cool roof coatings:Thoroughly clean the roof surface. Roofs collect oils from asphalt, chimneys, and cars plus lots of dirt and dust. ... Repair and seal roof penetrations, tears, open seams, etc. ... Apply coating when the roof is dry and the sealant has set.
Does Henry TropiCool need a primer?
If little to no effort is required to lift the fabric or if all of the coating pulls up from the roof, there is not sufficient adhesion for the application. If there is not sufficient adhesion, a primer must be used. Please consult Henry Product Support for specific questions regarding application of this product.
How long does it take Henry roof coating to dry?
Schedule work so that coating has 2 hours to dry before nightfall. NOTE: Ponding water resistant up to 48 hours. For older, low-slope roofs where depressions pond water for extended periods, Henry® 176 PondPatch® is recommended to provide positive slope in those areas and to eliminate ponding.
What kind of roller do you use for roof coating?
Apply first coat of roof coating using a one-inch nap roller, paint brush or a one gallon per minute or better airless sprayer machine with minimum tip size of . 025.
How long does it take cool seal to dry?
4-6 hoursDry Time: 4-6 hours between coats and before foot traffic: 24 hours minimum. Adhesion: Ideal for metal roof, single ply. smooth bitumen, polyurethane foam, concrete, existing asphaltic and elastomeric roof coating and other approved surfaces.
How long does Henry TropiCool last?
a lifetimeHenry 887 TropiCool is a fantastic roof coating that will last a lifetime. Henry 887 is not affected by the harmful rays of the sun and will not deteriorate over time.
How long does Henry TropiCool take to dry?
It is tack-free in about 1 to 2 hours and fully cured in about 48 hours (dependent on weather conditions, such as temperature and humidity). Not recommended for application at temperatures below 35°F (2°C) or if rain is expected in less than 1 hour of application.
Does Henry roof coating stop leaks?
Henry® Wet Patch® roof leak repair stops leaks instantly on wet or dry surfaces—even in pouring rain or standing rain. Repairs holes, cracks and splits on composition, mineral surface cap sheet, asphalt coated, SBS modified, metal, and masonry roofs.
How long does Henry roof coating last?
Unopened, 24 months from date of manufacture when stored in a cool, dry, and shaded location. Not recommended over shingles of any kind. CLEAN: Before coating the roof, use a pressure washer or high pressure nozzle and water hose to wash the roof with a non-filming detergent, such as TSP or TSP substitute.
How warm does it have to be to coat a roof?
Weather forecasts play a significant role in deciding when to apply roof coatings to maximize the results. Manufacturers recommend that temperatures at the time of application be at least 40 degrees — one suggested as high as 50 degrees.
Can you walk on elastomeric roof coating?
Drying/Curing Times In warm, dry conditions, the roof may be dry in a few hours; in humid conditions, it can take longer. Generally speaking, most elastomeric coatings will be dry to the touch and safe to walk on within eight to24 hours after application.
What is Henry Tropi Cool 887?
For those not familiar with Henry Tropi-Cool 887, it has been around for decades and is considered the best product for reducing heat on metal roofs from sun exposure. It is 100-percent silicone, much like the oven mitts made from the same material. Heat just doesn’t pass through it very well.
How hot does a roof air conditioner get?
Now that the ceiling heat isn’t working against the air conditioner, the air conditioner can get outside temperature of 92-degrees down to 63 in the cabin (see video above). The product itself is a bit expensive, but it’s the best on the market.
Does Dicor white rubber roof hold up to water?
I looked into the Dicor White Rubber Roof Acrylic Coating, the problem with this product it is an acrylic, and it will chalk off over time. Also, it will not hold up to water ponding on our rubber roof, especially on our slide out roofs.
Can you use silicone caulking on RV rubber?
You can’ t beat that! Now, silicone caulking is known to be a ”no-no” on an RV EPDM rubber roof. This product is a 100% Silicone coating that has no solvents to cure it out. The solvents are one reason a silicone caulking will not stick to an EPDM rubber roof.
