How do you adjust the idle on Poulan Woodshark?
- Place the saw on a flat bench and ensure there are no obstructions around the chain, which will spin during this procedure.
- Unscrew and remove the three screws holding the engine cover and remove the cover.
- Locate the idle adjustment screw.
- Start the saw and let it idle for two or three minutes to warm up.
- Tip.
How do I adjust the carburetor on my Poulan Chain Saw?
When adjusting the carburetor, you need to place your Poulan chain saw on a flat level surface with the chain overhanging the surface, or move all items so it will not come into contact with anything.
How does a Poulan woodshark chain saw work?
The Poulan Woodshark is a lightweight chain saw powered by a 2-cycle gasoline engine. The carburetor mixes fuel with the proper amount of air, and sprays the mixture into the combustion chamber where the spark from the spark plug ignites it to drive the engine piston and, ultimately, the chain.
Why is my Poulan woodshark stalling?
Improper idle adjustment can make your Poulan Woodshark stall. The Poulan Woodshark is a lightweight chain saw powered by a 2-cycle gasoline engine.
How do you adjust the idle speed on a Husqvarna chainsaw?
To adjust the carburetor idle speed, locate the idle speed screw labeled with a "T" just above the primer bulb. Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything.
How do you adjust the idle speed on a Poulan chainsaw?
Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed.
What is the L and H on a Poulan chainsaw?
The low end is when the trigger is first pulled. The H screw controls the air-fuel mixture of the high end of the chainsaw's throttle response. The high end is when the chainsaw's engine speed is topped out. Adjusting the L and H screws controls the chainsaws' throttle response, (low end), and high-end engine RPMs.
What is the T screw on a Poulan chainsaw?
The screw on top -- marked "T" -- is for adjusting the fuel mixture while the engine is idling. Of the two underneath it, the one on the left is for adjusting the mixture when the engine is running a low speed, and the one on the right is for making the same adjustment when the engine is running at high speed.
How do you adjust the H and L on a chainsaw?
0:254:29Chainsaw Carburetor Adjustment | How to Tune 'Correctly' - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo looking at the side of this chainsaw. We've got the H there and the L there. So this littleMoreSo looking at the side of this chainsaw. We've got the H there and the L there. So this little adjustment hole here is for the H. So the high and it goes all the way through and to the carburetor.
How do you adjust the carburetor on a Poulan Woodshark chainsaw?
6:297:40HOW TO ADJUST POULAN CHAINSAW CARBURETORYouTubeStart of suggested clipEnd of suggested clipTry one and a half on both and then go from there. So what you do is you screw in your screws rightMoreTry one and a half on both and then go from there. So what you do is you screw in your screws right down to the carb don't tighten too much and then count your turns.
Why does my Poulan chainsaw dies when I give it gas?
A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.
How do you adjust the carburetor on a Poulan Pro 42cc chainsaw?
2:237:01Carb Adjust on Poulon Pro 42cc Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn a little too high. Turn that low screw out it'll stop the chain from spinning and get it idlingMoreIn a little too high. Turn that low screw out it'll stop the chain from spinning and get it idling just right okay. Now if you look right here. Here's your low and your high screws to adjust the carb.
What is the fuel mix for a Poulan chainsaw?
40:1A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline.
How do you adjust the carburetor on a Poulan Pro pole saw?
1:415:41How To Adjust a Trimmer Carburetor, Poulan Pro, Craftsman, Weed Eater ...YouTubeStart of suggested clipEnd of suggested clipSo to reset i'll turn the idle screw clockwise all the way in. And then i'll unscrew itMoreSo to reset i'll turn the idle screw clockwise all the way in. And then i'll unscrew it counterclockwise. Three complete turns.
What does LH and T mean on a chainsaw?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet). Your saw may be labeled differently (in the photos in the Gallery below, the idler jet is labeled “S”), but you'll have three screws that correspond to these descriptions.
Why does my chainsaw not stay running?
0:052:01Top Reasons Chainsaw Starts, Then Stalls — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall.MoreOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall. You can try cleaning the arrestor with a wire brush. But you may need to replace it with a new one.
How do I get more power out of my chainsaw?
0:5411:47How I Got More Power From My Chainsaw! - 1 of 2 - #3 - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo guys are getting quite a bit more power out of just porting these a little bit. Now you'll seeMoreSo guys are getting quite a bit more power out of just porting these a little bit. Now you'll see the easiest and most common mod is just to drill some holes.
How to adjust carburetor idle speed?
To adjust the carburetor idle speed, locate the idle speed screw labeled with a "T" just above the primer bulb. Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything.
What is a Poulan chain saw carburetor?
A Poulan chain saw carburetor has a single feature to adjust with a tool to increase or decrease the idle speed. The carburetor is set correctly at the factory, but adjustments can be necessary if the engine runs poorly, dies or runs at a high speed. Engines that run at too high of a speed can be destroyed or run inefficiently. Engines that run at a slower speed than normal will stall and quit, then need restarting often.
Why does my chain saw make a high pitched sound?
In these cases, the fuel and oil ratio to air needs to be enriched. If the chain saw sounds as if it is running too rich, it will rev at high speeds and make a high-pitched sound.
