How to Hook Up the Fuel Line on My Craftsman Chainsaw
- Drain any fuel out of the fuel tank into a gas can. Unplug the spark plug boot and wire. ...
- Cut one end of both sizes of tubing on a 45-degree angle with the scissors. ...
- Attach the fuel filter to the newly straightened end of the smaller line. ...
- Measure the distance needed to get the fuel lines to the carburetor and then cut the lines straight.
How to replace fuel line on Husqvarna chainsaw?
How to Replace the Fuel Line in a Husqvarna 136
- Open the gas cap and pour out any remaining gas inside the tank. Empty the gas into an approved fuel container.
- Unscrew the four retaining screws that hold the cylinder cover in place over the air filter and carburetor.
- Unscrew the bolt that holds the air filter in place, using your hands. ...
- Bend one end of the metal wire into a hook. ...
How to replace fuel lines on Poulan Pro 220 chainsaw?
Things You'll Need
- Screwdriver
- Needle nose pliers
- Metal wire (baling wire)
- Scissors
- New fuel filter
How to clean the oiler hole on a craftsman chainsaw?
- Because chainsaws have two-cycle engines, the only lubricant is the oil you mix with the gasoline. If you don't add oil, the engine burns out. ...
- Don't use gas blended with ethanol or methanol, which become acidic and can damage your engine if left in the tank.
- Your chainsaw owner's manual specifies the ratio of gas to oil to mix for your chainsaw model.
How to replace the fuel filter on a Stihl Chainsaw?
Things You'll Need
- Gas can
- Hand siphon
- Metal clothes hanger
- Wire cutters
- Needle-nose pliers
Where do the fuel lines go on a chainsaw?
4:146:36Poulan & Craftsman Chainsaw fuel lines - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne of them goes from the carburetor. To the primer bulb. And be this top one and then the other oneMoreOne of them goes from the carburetor. To the primer bulb. And be this top one and then the other one goes from the prior bulb.
Where do the fuel lines connect on a craftsman?
3:2810:01Where do the fuel and primer lines go in a Craftsman or Poulan Chainsaw?YouTubeStart of suggested clipEnd of suggested clipAnd it's going to connect to the carburetor. And if you take a look at our carburetor. And you findMoreAnd it's going to connect to the carburetor. And if you take a look at our carburetor. And you find it.
Which fuel line goes to the primer bulb?
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
How do you install a fuel line on a chainsaw?
4:376:09Install Chainsaw Fuel Line In 20 Seconds: Make The Homemade ToolYouTubeStart of suggested clipEnd of suggested clipI'll quickly show you how it works one more. Time. Okay so we'll show you how it works you're goingMoreI'll quickly show you how it works one more. Time. Okay so we'll show you how it works you're going to take the tool you're going to push it right through the hole.
How do I put fuel lines in my tank?
2:354:35How to Replace the Fuel Line in a Line Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have the line in the hole use hemostat forceps or needle nose pliers to reach into the tankMoreOnce you have the line in the hole use hemostat forceps or needle nose pliers to reach into the tank. And grab the fuel line then pull the line through the fuel tank filler opening.
How do the fuel lines go on a Poulan chainsaw?
1:173:52Fuel Line Configuration on Poulan 2150 Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine goes inside the tank over there on the right-hand side.MoreLine goes inside the tank over there on the right-hand side.
Which fuel line is the return line?
The vapor-return line normally runs from the fuel pump or the fuel filter to the fuel tank. This vapor-return line is connected to a special outlet in the fuel pump. Any vapor that forms in the fuel pump returns to the fuel tank through this line.
Which fuel line goes where on a carburetor?
1:4115:37CORRECT FUEL LINE ROUTING AND BENCH TESTING 2 & 4 ...YouTubeStart of suggested clipEnd of suggested clipThe nipple closest to the fuel pump is the inlet side of the carburetor. And the other nipple is theMoreThe nipple closest to the fuel pump is the inlet side of the carburetor. And the other nipple is the discharge.
How do you hook up a fuel line to a carburetor?
2:418:29Carburetor fuel lines for dummies - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the idle screw the larger one on top then the one you see on top to your right is the gas lineMoreAnd the idle screw the larger one on top then the one you see on top to your right is the gas line and the other one is the return line. So the gas line connects to the top.
How many fuel lines does a chainsaw have?
Most chainsaws have two fuel lines -- one that feeds fuel into the carburetor and a return tube that allows unused fuel to flow back into the chainsaw gas tank. The return tube may be slightly larger in diameter than the tubing that feeds the fuel, or both tubes may be the same size.
How does the fuel system work on a chainsaw?
0:304:15How a Carburettor Works/Fuel Flow Fully Explained/STIHL/Two StrokeYouTubeStart of suggested clipEnd of suggested clipSo fuel was drawn in from the fuel tank into the main fuel Inlet tube with the carburetor. The fuelMoreSo fuel was drawn in from the fuel tank into the main fuel Inlet tube with the carburetor. The fuel is then taken in through the fuel veins inside the block of the carburetor.
How does a primer bulb work on a chainsaw?
Some chainsaws use a primer bulb to help suck gas into a cold carburetor. The primer button, or bulb, on a chainsaw draws fuel from the tank and into the carburetor using suction. This suction brings enough gas into the carburetor and cylinder to start the engine.
How to cut fuel lines in a tank?
Use a pair of scissors to cut the new fuel lines at an angle to thread them into the tank. Push the large line about 1 inch into the tank. Push the small line far enough into the tank so that it can be grabbed through the mouth of the tank with needle-nose pliers. Pull the small line out the mouth of the tank.
How to remove carburetor from engine?
Remove the carburetor. Using a 7/16-inch socket driver, remove the 2 mounting nuts that secure the carburetor to the engine. Pull the air filter housing off the carburetor. Pull the carburetor from the engine block, sliding it along the mounting studs. Be careful not to bend the throttle linkage or damage the gas lines.
What type of engine does a Craftsman chain saw use?
By Josie Myers. Craftsman chain saws run on a two-cycle gasoline mixture powered engine. An external primer bulb draws fuel into the engine. This require three areas of fuel lines: one from the fuel tank to the carburetor, one from the carburetor to the primer bulb and one from the primer bulb to the fuel tank.
How to remove the starter from a chainsaw?
1. Use the screwdriver to remove the main cover from the chainsaw. Unscrew and remove the air filter and the starter pull, which is blocking the primer bulb on most models. Also remove the primer as well as the carburetor and slide the fuel lines from both devices. Use the pliers to pull the fuel filter and hose lines from inside the gas tank.
What happens when a chain saw leaks?
When a leak occurs, it could be coming from any one of these three lines. If the fuel lines are brittle due to age, it is best to replace the entire line system while you have the chain saw in pieces.
Can you order parts directly from the manufacturer?
Ordering parts directly from the manufacturer or an approved vendor will ensure your have the correct size of fittings and hoses. An improper fit will only cause more leaks. The gasoline and oil mixture can be caustic for skin, so use chemical-resistant gloves and eye wear in case of splashes.
