How do I tighten the rubber on my Otterbox?
- Fill a pot up with hot water.
- Drop the rubber seal into the pot of boiling water for 1 minute.
- Install the rubber seal to check the fit.
- Use a heat gun to shrink rubber seals that need to shrink in place.
How to fix OtterBox silicone case?
Remove the rubber from the boiling hot water and put on ice cold water for about 10-20 sec. Dry the silicone case with paper towel or cloth and then I hope it will be good as new. This method is usually used for fixing silicone mouthguard but I heard it is working well to fix the Otterbox silicone.
Why are my OtterBox rubber silicone earbuds loose?
This can happen as well due to your working environment and that includes the weather particularly when it is hot and humid. To get the maximum protection, Otterbox rubber silicone must fit firmly into your phone. Therefore it is important to fix it if they are getting loose.
How do I clean the rubber on the back of the case?
Firstly you need to boil some water and make sure it is boiling hot. Remove the rubber from the case and put in the boiling water for about 30sec - 1 min. Remove the rubber from the boiling hot water and put on ice cold water for about 10-20 sec.
How do I shrink the rubber on my OtterBox?
1:112:44How NOT to Fix an Otterbox Rubber Cover | Stretched Out Cell Phone ...YouTubeStart of suggested clipEnd of suggested clipSit over on this towel. Now I've seen some people put the silicone back on the case and let it airMoreSit over on this towel. Now I've seen some people put the silicone back on the case and let it air dry then some people put the silicone case into the water and let it shrink.
How do I tighten the back cover of my phone?
0:002:17How To Shrink Your Phone Case #shorts - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere. When the time is up put your silicone case into the cold freezing. Water. Then put your caseMoreHere. When the time is up put your silicone case into the cold freezing. Water. Then put your case in the cold. Water.
How do you open the tension clip on an OtterBox?
Release the tension clips along the edge of the case. Use your fingers to pop the clips up one by one until the 2 sides separate and fall off your device. If you can't get your finger under the clip, you may need to use a small flat-head screwdriver or a stiff credit card to get some leverage.
How do I put my OtterBox back together?
0:031:25How to install an OtterBox Defender Case in Under 1 Minute! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply run your nail in that long clip that put the phone. In click the protector back over the topMoreSimply run your nail in that long clip that put the phone. In click the protector back over the top like. So very quick very easy to do make sure that all the clips are in place.
How do I keep my OtterBox from stretching?
Stick the rubber part in the pot and leave it for 2 minutes. Then take it out and let it dry and it's like new again! Well I tried it on mine and it did work. I've never had an issue (other than stretching) with an otterbox and it has protected my phone wonderfully from all sorts of drops, some water, etc.
How do you fix a loose silicone case?
Just boil some hot water, then take it off the stove and throw the silicone case in there for a few minutes. Take it out (dry it first obviously) and try it on, if still loose repeat until it works.
How do I fix my OtterBox clip?
0:000:37Otterbox Defender Releasing Stuck Clip - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the OtterBox. Defender this is for the iPhone 6s. And sometimes when you push the clip down it'llMoreOn the OtterBox. Defender this is for the iPhone 6s. And sometimes when you push the clip down it'll get snapped into sort of a permanent.
How do you use an OtterBox belt clip?
Put your thumb on the top of the belt clip (the part that opens and closes over your belt) and push down. It's that easy. The belt clip is even more useful then Otterbox lets on about – it doubles for a vertical or horizontal video stand. Customer service is also outstanding!
How do you change the clip on an OtterBox case?
Taking out the silicone is the only way to replace it. Open the tension clips and they should open. Make sure you let both halves separate until they reach a point where they're no longer attached. Continue reading if you would like to learn how to remove an Otterbox Case from an iPad.
How do I put the Otterbox Defender on my iPhone?
1:042:52How To Install iPhone X Into Otterbox Defender Case! - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst then simply just fold the top frame of the case over next to make your way around the entireMoreFirst then simply just fold the top frame of the case over next to make your way around the entire case. Making sure that it's properly snapped together.
How do you put on an Otterbox Defender Pro?
0:091:41How To Install an OtterBox Defender or Defender Pro (Most Phones)YouTubeStart of suggested clipEnd of suggested clipSo first step peel apart the case here just by separating the rubber from the inner plastic. PieceMoreSo first step peel apart the case here just by separating the rubber from the inner plastic. Piece um this can be a little bit difficult to first go around but usually gets a little bit.
How do you put on an Otterbox symmetry case?
0:030:36OtterBox Symmetry Series | Install Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipLet's get your sleek symmetry series case installed slip the side of your phone into the long edgeMoreLet's get your sleek symmetry series case installed slip the side of your phone into the long edge of the case making sure all the buttons and ports line up with the openings in the case.