How do I reset my power pole remote?
- Featuring.
- Press and hold the PROGRAM button on the top of the unit for 3 seconds until the LED turns green (HPU will also beep).
- To raise or lower the spike, press and hold either the UP or DOWN button on the remote control.
- Ensure the surrounding area is as dry as possible to avoid any moisture intrusion.
- Figure 1.
Full Answer
How do I reactivate the power-pole?
To reactivate, press both buttons again for 3 seconds until LED lights flash. KEY FOB Remote Control STANDARD MODE To raise or lower the Power-Pole, press and hold either the UP or DOWN button on the key fob. The anchor will only continue to move so long as you press the button. AUTO MODE
What to do if your power pole keeps going down?
If the fuse is blown, then you can quickly fix this issue by replacing the fuse. Other than that, you won’t have to do much else, and the power pole will start going down once you’ve replaced the fuse.
How do I set the power-pole on the dash switch?
• Set as a single HPU-Press and hold both UP and DOWN buttons simultaneously. • Set as starboard side HPU-Press and release the UP button. • Set as port side HPU-Press and release the DOWN button. Dash Switch STANDARD MODE To raise or lower your Power-Pole, press and hold either the UP or DOWN button on the Dash Switch.
How do I replace the Potting On my remote?
Take the remote box off and gently push on the potting in the back of it. If the potting pulls away from the edges of the box power pole will cover it under warranty. Contact power pole before replacing anything.
How to reset a remote to work?
How to turn on HPU?
How to prevent moisture intrusion in a house?
About this website
How do you reprogram a power pole remote?
0:170:51Power-Pole Controller Programming - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first thing you're going to do is locate the small red program button on top of the pump. YouMoreSo the first thing you're going to do is locate the small red program button on top of the pump. You're going to hold this button for approximately three seconds.
How do you unpair a power pole remote?
loosen the 4 screws that hold the cap to the remote box and hold the program button on the right side, (its red) for 3 seconds and then hold down a button on your remote. The remote will re-learn the signal and you should be good to go, if everything else is working normally.Feb 2, 2020
How do I reset my micro power pole?
0:091:00Calibrating the Power-Pole MICRO Anchor - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt into the micro unit. And on the top of the unit there's an anchor force button and a batteryMoreIt into the micro unit. And on the top of the unit there's an anchor force button and a battery level but press them both at the same time.
How do you change the speed of a power pole?
0:311:31Power-Pole Standard Remote Control Speed - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd hold down the program button for a total of six seconds. The light will end up turning. Red.MoreAnd hold down the program button for a total of six seconds. The light will end up turning. Red. Once red release. And now I hit it one more time.
How do you use the C Monster app?
0:081:40Power-Pole C-Monster App - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo up and down with the pole. Obviously right from the app you can adjust the speed settings.MoreGo up and down with the pole. Obviously right from the app you can adjust the speed settings.
Are power pole remotes waterproof?
The Power Pole CM2 Remote Control Transmitter Fob with C-Monster 2.0 allows you to enjoy wireless control from anywhere on your boat. Included with a floating lanyard, the Power-Pole CM2 Remote Control Transmitter Fob features double-click for auto-up/down and it's completely waterproof.
How does a micro power pole work?
0:512:03Power-Pole Micro Anchor - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr Ankara hands-free the way it operates if you double tap. Basically the anchor goes down fineMoreOr Ankara hands-free the way it operates if you double tap. Basically the anchor goes down fine finds the bottom and space stays put and you can make your caster. You can plan the fish.
How do you use a power pole anchor?
2:423:39How to use Power Poles - YouTubeYouTubeStart of suggested clipEnd of suggested clipLeave my poles I'll fishing around with them about halfway down. And if I see something that reallyMoreLeave my poles I'll fishing around with them about halfway down. And if I see something that really catches my eye. The poles gonna get to the bottom way way faster.
How long is power pole warranty?
Warranty – Power-Pole offers a 5-year warranty on Blade and Pro II models, and 3 years on the Sportsman II vs 5 years on all models. Repair - Power-Pole anchors can be repaired at any of our over 1500 nationwide dealer network facilities including over 300 Certified Warranty Centers vs. regional repair centers.
What kind of oil does a Power-Pole use?
Green Marine hydraulic fluidPower-Pole has developed Green Marine hydraulic fluid to provide the performance of a petroleum product without the harmful effects. This ISO-32 fluid is ideal for use in Power-Pole systems, trim tabs, jack plates, tilt and trim rams, hatch lifters and more.
How do you service a Power-Pole?
0:382:43Power Pole Maintenance Tips - Nuts, Bolts, and Brackets. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo one of the things we need to be doing with our power poles is just checking on these connections.MoreSo one of the things we need to be doing with our power poles is just checking on these connections. Here making sure these bolts and the nuts. And washers are still in good condition.
What oil do you use for Power-Pole?
A: The HPU reservoir should be filled with Green Marine® biodegradable hydraulic fluid or an ISO 32 hydraulic fluid. Green Marine is available through all authorized Power-Pole dealers.
What if your Power Pole sticks down? - Texas Fishing Forum
361, I have the 8' blades and they will do the same every now and then. Push and hold UP on your remote for a few seconds. If that doesn't work, put the other one back down and then double-punch the remote to come up.
Power Pole Remote Not Syncing - Dedicated To The Smallest Of Skiffs
So my 2007 BT has from what I believe is the older 2008 power pole with the manual switch that works fine on the center console, but my controller died. Went to TMS to get my new trolling motor installed in town and got a hold of 2-3 other older mag sync remotes to try and program them to the...
Power pole stuck in the down position! | 2 Cool Fishing Forum
I hit the ramp early and backed the boat off the trailer at the dike. I parked it against the pier and put the power pole down while my partner parked the truck. When I went to leave the power pole would not come up. It had fluid and the pump was making noise in the up and down position on the...
Power Pole troubleshooting | Dedicated To The Smallest Of Skiffs
Need some help from the more mechanically inclined here. My 8' signature series (a couple of years old) stopped working on the remote. I can still make it work from the switch wires and have removed the plug and straight wired that, still not working. Anyone have any tips for what the cause...
Power Pole Issues? - Marine Electronics - Bass Fishing Forums
It's the Power Pole 8' Pro Sereies II model. I bought it two years ago. And never once had an issue with it. Until I got on the water for the first time and went to deploy from my wireless remote and then I got nothing.
Power Pole Troubleshooting: 3 Problems With Their Solutions
power pole troubleshooting. Power Pole is a handy device that you can use in shallow water. The depth of the water should be under the limit defined by the length of the power pole.
What does 2 beeps mean?
2 beeps =Changes the speed of the standard Key Fob Remote Control. (FIG. 2)
How long does the anchor stay on the key fob?
on the key fob. The anchor will only continue to move so long as you press
How to tell if a switch is in sleep mode?
Press both UP and DOWN buttons for 3 seconds, LED lights will flash indicating the switch is now in Sleep
What does "Auto Up" mean?
to move in said direction until it either retracts completely (Auto Up) or
How to raise power pole?
To raise or lower your Power-Pole, press and hold either the UP or
Does the Power Pole anchor come with the Dash Switch?
Your new Power-Pole anchor comes paired to the included Dash Switch and Key Fob remotes . When installing
Can a dash switch be used with multiple anchors?
With multiple Power-Pole an chors equipped with the C-Monster Control System, the Dash Switch can be
How to fix a power pole that is blown?
First, you need to start by checking the fuses in the power pole housing. Depending upon the installation of the power pole, you need to open up the housing and check fuses to see if they are blown. If the fuse is blown, then you can quickly fix this issue by replacing the fuse. Other than that, you won’t have to do much else, and the power pole will start going down once you’ve replaced the fuse.
What is the purpose of a power pole?
The primary purpose of the Power-Pole is to extend into the water and keep your boat fixed in a place. That way, you won’t have to worry about excessive winds while fishing. Here we will be covering some of the most important troubleshooting steps a Power Pole. Along with that, we will be listing some possible fixes that you can use to fix said problems. So, if your Power-Pole is not working as it should, just follow through.
Can you replace a power pole controller?
As the last shot, you can try programming the controller again as well. If you’re facing the same problem, then now is the time to look for a controller replacement.
How to reset a remote to work?
have you tried resetting the remotes? loosen the 4 screws that hold the cap to the remote box and hold the program button on the right side, (its red) for 3 seconds and then hold down a button on your remote. The remote will re-learn the signal and you should be good to go, if everything else is working normally.
How to turn on HPU?
Press and hold the PROGRAM button on the top of the unit for 3 seconds until the LED turns green ( HPU will also beep).
How to prevent moisture intrusion in a house?
Ensure the surrounding area is as dry as possible to avoid any moisture intrusion.
