How do I reset my Hayward salt system?
- Turn Salt System Off and On. With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”.
- Average Salt Reading. Wait until the numbers stop changing.
- Assess the Salt Cell Reading.
How do I Reset my Hayward salt cell?
To reset your Hayward Salt Cell, position the switch to off and then turn back to Automatic. After that, you will need to be patient for five to ten seconds for the relay to click. During the point when the instant salt level is steady (and the negative indication is actually present), twist the switch to ‘Super Chlorinate and back to Automatic.
How do I recalibrate my Hayward aquarite?
Accordingly, how do you recalibrate Hayward AquaRite? Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.
How do I Turn my salt system off and on?
Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row.
How do you reset the inspect cell light on a Hayward?
If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use. Click to see full answer. Beside this, how do you recalibrate a Hayward Salt Cell?
How do I reset my salt system?
Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.
How do you recalibrate salt cell Hayward?
1:022:17Recalibrating an Aquarite Salt Chlorine Generator - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst step slide the main switch to the auto. Position. Second step push the diagnostic button untilMoreFirst step slide the main switch to the auto. Position. Second step push the diagnostic button until a T number appears on the display.
How do you reset a salt pool cell?
1:073:16Reseting Pool Salt Generator - YouTubeYouTubeStart of suggested clipEnd of suggested clipScreen. So you're going to turn the system off. And then you're going to turn the system back on andMoreScreen. So you're going to turn the system off. And then you're going to turn the system back on and then you're going to hit this five times.
How do I reset my Hayward check system?
You must reset the system by entering the 'Diagnostic Menu' and then hitting the right arrow key once and then pushing the plus (+) key once. This should reset the light and message.
How do you troubleshoot a Hayward salt Cell?
1:184:19How To: Troubleshoot a Hayward AquaRite - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe high salt LED is illuminated. Check the salt level with a test kit if the salt level is too highMoreThe high salt LED is illuminated. Check the salt level with a test kit if the salt level is too high lower. It by draining some of the pool water via the pools wastewater.
How do I know if my Hayward salt Cell is working?
The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. On the chlorinator box there should be a light or dial that indicates it is working.
How do I reset my chlorinator?
0:071:31Chlorinator reset. Having electrical issues with your Hayward unit. Pure ...YouTubeStart of suggested clipEnd of suggested clipSo you've got to hold it for a bit. And then it'll go through it's little numbers go through itsMoreSo you've got to hold it for a bit. And then it'll go through it's little numbers go through its setup. Then you release that. And it has reset.
How do I know if my Hayward Turbo is working?
The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochlorite gas) inside the chamber, producing what looks like cloudy water - that's chlorine being created!Oct 24, 2018
Why is my salt cell light blinking?
If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires.
How do you adjust a Hayward chlorinator?
0:141:09How to Operate your Hayward Chlorinator - YouTubeYouTubeStart of suggested clipEnd of suggested clipProducts begin by turning off the electricity to your pump motor. Open the top lid of theMoreProducts begin by turning off the electricity to your pump motor. Open the top lid of the chlorinator by depressing the locking tab and by turning the cover counterclockwise.
How do you turn on a chlorinator on Hayward?
1:233:09ProLogic: Programming Diagnostics - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the right arrow button. If the chlorinator is enabled cell temp sensor and turbocellMorePress the right arrow button. If the chlorinator is enabled cell temp sensor and turbocell temperature is displayed. Press the right arrow button water sensor and water temperature will be displayed.
What does inspect cell mean on salt water pool?
If both the “check salt” and the “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. Both lights will also stay on if the controller is set to the wrong turbo cell type, or if the cell is unplugged.
Why is my salt cell not working?
Another common cause of salt cell failure is improper water balance. One may also ask, how do I know if my salt cell is bad? If the salt cell does not bubble, then you either have no power to the cell or you have a bad cell. Further troubleshooting will be required.
Why do salt cells fail?
Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. Use a cleaning kit designed for salt cells to keep the plates clear of buildup. Another common cause of salt cell failure is improper water balance.
How long does it take for an inspection cell light to reset?
If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use. Click to see full answer.
How to reset Hayward Aquarite?
How do I reset my Hayward AquaRite? If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
How long does it take for an inspection cell light to reset?
If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use. Click to see full answer.
What does the check salt light on a Hayward Aqua Rite mean?
If the “check salt” light is lit on a Hayward Aqua Rite salt chlorinator, it could mean a number of things. First, check the display salt reading – if it’s 2,700 ppm or lower, the check salt light will come on. We always recommend an independent salt level test. If the salt level is fine, inspect the Cell and clean if necessary.
How long does it take for an inspection cell light to reset?
If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
Can you add salt to an Aqua Rite pool?
If the salt level is fine, inspect the Cell and clean if necessary. Never add salt without first having the water tested independent of the Aqua Rite reading. Salt only leaves the pool from backwashing a filter, splash out, leak or removing water from the pool.
Does salt chlorination work?
This more natural approach to chlorination eliminates the harsh chlorine odors caused by chloramines and leaves your pool feeling healthier and more luxurious. With Salt Chlorination, you receive a continuous supply of fresh, natural chlorine that is constantly circulated throughout your pool.
How to recalibrate Aqua Rite?
Before recalibrating, test the water with salt water test strips to determine the correct salt level. If the results from your test strip are not the same as the Aqua Rite, proceed to step 2. Click Here to View Salt Test Strips.
Does the Hayward Aqua Rite match the salt level?
WRITTEN BY: Inyo Pools. Occasionally the salt level on the Hayward Aqua Rite may not match the actual salt level of the pool. If the salt cell is clean but the salt reading is off, the Aqua Rite will need to be recalibrated. The following steps will provide a guide on how to recalibrate a Hayward Aqua Rite.
