If you are troubleshooting a Baxi boiler that uses an ON/OFF/SELECTOR switch to reset:
- Open the pull down panel to reveal the control.
- If a fault occurs on your boiler, an error message or light (depending on your boiler model) may be shown on the fascia display. In the example shown, ...
- If your boiler uses a series of neon indicator lights (instead of an LED display) a lockout is shown through the flame failure light. On the 10-Neon ...
- The process of resetting your boiler is the same regardless of the fascia display.
- To reset the boiler, turn the selector switch to the R (Reset) position. Hold for at least 5 seconds and release.
How do I Reset my Baxi boiler?
If you are troubleshooting a Baxi boiler with a dedicated reset button: In certain circumstances, your boiler may lock out. This is identified by the Red Lockout light constantly illuminated or flashing. To reset the boiler, simply press the reset button until the red light goes away.
What does error code E133 mean on a Baxi boiler?
During the winter months, it wouldn’t surprise us if you see error code E133 or E28. Condensate pipes in Baxi boilers (and most other brands) transport the wastewater away from the boiler, straight into the drain outside.
What does E168 mean on a Baxi boiler?
Baxi Boiler E168 Error Code When your Baxi boiler has an issue but cannot work out where the problem is, it will show this error. The most common cause for seeing this code is when there is a problem with the electrical supply (PCB lockout error).
Why is my Baxi 1pf boiler not heating up?
A common culprit for this fault on Baxi boilers is a lack of pressure. If your system is set lower than 1.5 bar then it won’t operate correctly. Now, the quick fix is to top up the pressure using the filling loop. Once you’ve topped up the pressure, you’ll need to reset the boiler. On the Baxi 1PF you’ll see an orange button.
What does E133 mean on a Baxi boiler?
E133. Indicates that the gas supply has been interrupted, ignition has failed or the flame has not been detected. Ensure that the gas supply has not been turned off, and turn the selector switch to the reset position and hold for at least 5 seconds.
Where is the reset button on a Baxi boiler?
0:201:08How to reset your boiler - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe button to the left of that would then flash red quickly and the boiler would then start itsMoreThe button to the left of that would then flash red quickly and the boiler would then start its reset.
Why is my Baxi boiler not firing up?
A common culprit for this fault on Baxi boilers is a lack of pressure. If your system is set lower than 1.5 bar then it won't operate correctly. Now, the quick fix is to top up the boiler pressure using the filling loop. And once you've topped up the boiler pressure, you'll need to reset the boiler.Apr 5, 2022
How do I fix error E133 on my Potterton boiler?
If you are seeing the error code E133 on your Potterton boiler, this means that your boiler condensate pipe is frozen....Potterton Assure Combi and system Boiler Error Codes.Fault CodePossible CauseE133Possible gas supply issue (failure to light)29 more rows
How do I reset my Baxi?
Most Baxi boilers have a simple reset button on the front panel - locate this and press and hold the button for 1 to 3 seconds or until it's clear that the boiler has rebooted itself.Sep 15, 2021
Why is my boiler not resetting?
If you find that you keep having to reset your boiler, it's likely that there could be a fault with your heating system. This fault could eventually lead to a more serious issue such as a boiler breakdown, so it's best to seek out a solution as soon as possible.May 13, 2020
Why is my boiler not lighting?
A boiler might not ignite due to various possible reasons – insufficient pressure, blockage in the burner, faulty valves, frozen pipes etc. Sometimes, you can fix the problem on your own. In other cases, you don't have any choice but to call an engineer.
How do you reignite a boiler?
Press and hold the reset switch for one minute and hold a flame to the pilot light at the same time. Ensure you only hold the switch down once the pilot light has ignited, to reduce the chances of any gas accumulating again. When you release the button, the flame should stay.
How do you restart a boiler?
Follow these simple instructions to reset your boiler:Refer to your boiler manual.Push the reset button for 10 seconds.Wait 2 - 3 minutes, the boiler should fire up.Repeat twice if the first attempt fails.If the boiler still fails to fire up on the third attempt, double check the gas supply.More items...
How do you fix E133?
If your boiler has shut down and is showing error code E133 or E28, then your condensate pipe may be frozen.Switch your boiler off at the control panel, and turn off the electricity at the wall.Find where the pipe is frozen, usually the most exposed part of the pipe.More items...
How do I fix E133 error on Baxi boiler?
0:283:11What to do with Baxi E133 error code on the GA range of boilers - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo reset the boiler press and hold the standby reset button for one to three seconds. Your boilerMoreTo reset the boiler press and hold the standby reset button for one to three seconds. Your boiler will now attempt to relight a maximum of five. Times.
How do I reset my Potterton profile boiler?
Potterton Profile: Make sure your heating is turned ON at the programmer, and in particular the room thermostat is turned up high. ... find and press the 'reset' button underneath. ... The pilot light.
What is the E133 code on a boiler?
E133 error code on a Baxi/ Potterton / Main boiler is an ignition lockout fault code. This error code that covers a wide range of possible faults connected to gas and igniton. In most cases you will need to contact a competent boiler repair engineer but there are some steps you can take yourself before booking a repair: 1 check if gas supply is turned on – if you have a gas hob see if there is gas coming to the gas hob. You can also check if your gas meter ECV (Emerngecy Control Valve) is turned on parrarel to the pipework 2 check if your meter has credit (Pre paid meters only) 3 if outside temperatures are below zero – check if condensate pipework is frozen. If it is pour hot water over the pipework. 4 check if your condensate pipework is not blocked
Why does my boiler not ignite?
(Flame led does not illuminate and there is no flame visible in the sight glass) Possible causes in this case are: faulty gas valve. faulty wiring between gas valve and PCB. faulty PCB.
Turn Off the Boiler
If you find yourself in this scenario, the first thing that you should do is turn off all external switches apart from the button located on top of your control panel.
Check Error Indicator
Once your Baxi boiler has been turned off again, check the indicator on your control panel for error messages. Look at whether there is an energy failure indicated by an E5 symbol that will require resetting the device before it will work again.
Get a Gas Fitter
If the error message persists even after you have followed the previous steps, it is time to consider getting a gas fitter in to help you with your problem. The service will last approximately an hour and cost around £75, which you should be prepared for if this happens.
Do Not Touch the Gas Safety Device
The gas safety device of any home appliance is both dangerous and delicate; it has to be handled by people who are trained or authorized for the job.
Do Not Touch Red Hot Parts
This includes all the elements within the Baxi machine itself because if they are damaged during servicing processes, they will have no other choice but to replace them.
Do Not Maintain the Repair Unless You are Skilled
There are many reasons why owners should never try to do this job on their own, especially if they have no idea about how something works in the first place.
Do Not Take Off the Whole Boiler
If there is something wrong with the Baxi machine, owners should never attempt to fix it by taking out or removing all parts from inside as this is very difficult according to this article “ how difficult is it to move a boiler ”.
How to fix a frozen boiler?
Please follow these steps to get your boiler up and running again: 1 Switch your boiler off at the control panel, and turn off the electricity at the wall. 2 Find where the pipe is frozen, usually the most exposed part of the pipe. 3 Warm the condensate pipe across its exposed length using either a hot water bottle, a microwaveable heat pack or warm water poured from a watering can. Do not use boiling water straight from the kettle as this could damage the pipe. 4 Turn the power back on at the wall and restart your boiler. Repeat the process until the boiler works again.
How to warm condensate pipe?
Warm the condensate pipe across its exposed length using either a hot water bottle, a microwaveable heat pack or warm water poured from a watering can. Do not use boiling water straight from the kettle as this could damage the pipe. Turn the power back on at the wall and restart your boiler.
What is the error code for Baxi boiler?
During the winter months, it wouldn’t surprise us if you see error code E133 or E28. Condensate pipes in Baxi boilers (and most other brands) transport the wastewater away from the boiler, straight into the drain outside.
Why does my Baxi boiler show a code?
The most common cause for seeing this code is when there is a problem with the electrical supply (PCB lockout error).
Why does my Baxi boiler have 3 red flashes?
3 red flashes, as discussed above, means your ignition is failing to light and that your boiler has self-reset 5 times and is still facing the same issue. Unfortunately, some Baxi boiler models can be prone to this fault and you may need to replace chamber seals if they have worn or degraded over time.
What does it mean when your boiler flashes green?
1 green flash simply means your boiler is up to the temperature you requested. 3 green flashes means the flame went out . If this is a temporary issue, the boiler should reset by itself. If it cannot fix this it will turn into 3 red flashes (see red flashes and also see how to manually reset your boiler below).
How to check if a boiler is leaking?
You can do some visual checks to try and isolate the problem. Check for leaks on: 1 Radiators 2 Towel rails 3 Pipework 4 Radiator valves 5 Beneath the boiler (this could be the pump) 6 The expansion vessel
What is the normal water pressure for a Baxi boiler?
The normal water pressure for a Baxi is between 1.0 and 2.0 bar. Suggested fix. You may need to check your gauge and note if the water pressure is less than 1.0 bar. It is not uncommon for boilers to need to be repressurised and in most cases, you can do this yourself.
What does error code 110 mean?
In houses with older, traditional radiator heating systems, you are more likely to see Error Code 110. This simply means your boiler has overheated. Firstly, attempt to bleed your radiators. This simply means you’re letting any trapped air in the radiator out.
