- Enter your vehicle and close the doors and trunk behind you. Have the remote starter and your ignition key in hand.
- Insert the key into the ignition and switch it from "Off" to "On" three times, ending in the "On" position after the third cycle.
- Push the valet switch on your Autopage alarm twice. Hold the button on the second push until you hear a chirp, signifying that the programming sequence is ready.
- Press any button on your keyless remote starter. The vehicle will respond with another chirp to indicate that the programming was successful.
- Repeat Step 4 with any additional remotes if necessary. ...
What is Autopage remote start?
Autopage is a leader in keyless entry, remote start and alarm systems for cars across the United States. The company's car starter offers a remote way to start your car from up to a couple hundred feet away and allows you to access your vehicle's locks, trunk and panic alarm.
How do I program my Autopage alarm to my car?
Push the valet switch on your Autopage alarm twice. Hold the button on the second push until you hear a chirp, signifying that the programming sequence is ready. The valet switch is located near the bottom of driver's dashboard, where the alarm is set up. Press any button on your keyless remote starter.
How do you start a car with a remote starter?
The company's car starter offers a remote way to start your car from up to a couple hundred feet away and allows you to access your vehicle's locks, trunk and panic alarm. Enter your vehicle and close the doors and trunk behind you. Have the remote starter and your ignition key in hand.
What are the advantages of remote control automobile technology?
As automobile technologies advance into the remote-control world, safety and convenience have been among the chief beneficiaries. Autopage is a leader in keyless entry, remote start and alarm systems for cars across the United States.
What is the valet switch on autopage?
The valet button or switch permits the owner to temporarily bypass the alarm functionality of the system. To enter or exit valet mode, disarm the system with a working transmitter, your personalized manual override code, or using the procedure below which is to enter or exit valet mode.
How do I use autopage xt12 remote start?
Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in the 'ON' position. Within 15 seconds. Push the Programming switch 2 times holding in on the 2nd push, until a long chirp from the horn (optional) and the LED starts to flash then release the valet switch. You are now in the Transmitter programming mode.
Who makes autopage remote start?
Auto Page, maker of remote starters, and its owner Varad, maker of automotive lighting, closed their doors almost two weeks ago, and laid off all remaining personnel with the exception of VP Carl Stacy, said industry members.
How do I turn off valet mode on autopage?
1. Return to normal operation, turn ignition 'ON'. 2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting the valet mode.
Why is my remote car starter not working?
If your remote starter system isn't working properly, try replacing the battery in your fob. You can find replacement key fob batteries at Batteries Plus. Most remote starter fobs run on 2032 lithium coin cell batteries. This one may seem obvious, but if your vehicle is not in "Park" your remote starter will not work.
Where is the valet switch located?
Typical locations for valet switch: Under the driver's side dash (mounted in the under-dash covering trim panel or wire-tied to a harness) Mounted in the driver's side kick panel. Mounted in the steering column plastic housing.
What is the valet override button?
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational.
What does valet mode do?
Valet mode allows the vehicle to be driven and locked by a parking attendant, without giving access to the loadspace. Valet mode also prevents operation of the Touch screen, to prevent access to telephone numbers or navigation addresses.
How to program Ford remote start?
For those of you who need to program a new auto start remote, you turn the ignition to the on position, push and hold the little over-ride button (mine is down on the left side kick plate near the hood release) for about 15 seconds, you will hear a chirp which means the system is ready to be programmed, just hit the lock key on your remote and the system will chirp acknowledging the remote has been programmed, continue to do this will all other remotes you have within I believe it was 20 seconds - then shut off the ignition and test your remotes. Worked perfectly for me.
How to reset a fob?
two points 1 replace batterys in fob .2 place key in drivers door and turn this acts as a reset might take a couple of turns.hope this helps you.adrian