How do I know if my washing machine water pump is bad?
- Check the washing machine power cord to ensure it is unplugged from the electrical outlet.
- Turn on the ohmmeter and touch the probes together. Adjust the scale dial to zero.
- Find the two wires connecting to the side of the pump.
- Touch a probe to each of the terminals on the pump.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle. ...
- Wait for the washer to finish its cycle.
What happens if my washing machine drain or pump is bad?
If your washing machine drain or pump are experiencing problems, it'll hinder the performance of the appliance. Find out how to diagnose and repair such faults by watching this eSpares video.
How do I know if my pool pump is bad?
You should see the drain pump attached to the bottom panel. It is connected to the drain hose. Remove the drain hose by unscrewing the clamps holding it to the pump outlet. Look for blockages inside the hose, says Family Handyman. If you don't see any, the pump may be blocked or faulty.
How do I know if my washing machine filter is bad?
If the pump is broken, you'll probably hear sounds when the machine is running. Some manufacturers provide a filter that catches lint before it gets to the pump. The machine won't drain if the filter is blocked. You should be able to access the filter when you remove the front panel.
Why is my Kenmore washer not turning the pump on?
Typically one of three problems occur with the pump. The first is a blockage in the pump, often from small items like a sock. The second possibility is that the impeller blades become broken or worn down and cannot move water efficiently. Finally, in belt drive models, if the belt is loose or broken it does not turn the pump.
How do you diagnose washer drain and pump problems?
1:564:23How to Diagnose Washing Machine Drain and Pump Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you're getting strange noises during the wash cycle. That's more likely to be a problem withMoreSo if you're getting strange noises during the wash cycle. That's more likely to be a problem with the recirculation pump. If the noises are happening during the drainage.
How do you test a washing machine pump?
Use a small screwdriver to turn it. Watch out for rubber bands wrapped underneath the impeller making it too stiff for the pump to run. You can try running the washing machine on drain or spin with the filter out and check to see if the impeller is turning or attempting to turn.
How do washing machine pumps fail?
A pump can fail in two ways: mechanically and electrically. A mechanical failure can be caused by a foreign object caught in the pump, or direct damage to a pump component, such as the impeller. Inspecting the pump can often reveal a mechanical failure. An electrical failure can be diagnosed by using a multimeter.
How much does it cost to replace a pump on a washing machine?
The price of a new washing machine pump is $25 to $40 on its own, not including labor. When hiring a professional, repair prices range from $200 to $450.
How do I know if my drain pump is working?
0:522:51Front Load Washer Won't Drain - How to Test the Drain Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe motor test is good. And it was getting voltage. So you know and you know it's going to runMoreThe motor test is good. And it was getting voltage. So you know and you know it's going to run whenever you hit the start button it's going to pump the water out.
Is my washing machine pump broken?
Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you'll be able to feel them while you're turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
How long should a washing machine drain pump last?
How Long Do Washing Machine Pumps Last? Depending on the drain pump quality, you can expect it to last anywhere from 3 to 5 years. However, it's not uncommon for drain pumps and other washer components to last upwards of 10 years.
How do you unblock a washing machine pump?
How to unblock Your Washing Machine (8 Easy Steps):Turn your washing machine off at the plug. ... Locate the pump filter. ... Place a bucket, towel or even a baking tray under the pump filter. ... Unscrew the pump filter SLOWLY. ... Wait for the water to finish draining. ... Check to see if there is a block.More items...•
Should a washing machine drain pump spin freely?
It should move freely. However, some impellers may feel like there's a small resistance which when overcome allows the impeller to jump 180 degrees round.
What is the lifespan of a washing machine?
10-13 yearsHow long does a washing machine last? A typical washer should last 10-13 years. Top-loading washers typically last a few years longer than their front-loading brethren. If you use a stacked washer/dryer combo, you may have to replace both if one starts acting up.
Is it worth getting a washing machine fixed?
Again, you should replace the washing machine if the total cost to repair exceeds 50% of the cost of a new unit. It's advisable to check your warranty when you want to repair or replace a washing machine. Your costs may come down significantly if the appliance is still new and under warranty.
How long should a washing machine last?
around 10 yearsWashing machines, on average, last around 10 years, according to Consumer Reports.
About Washing Machine Drain Pumps
Washing machine drain pumps are nearly always mounted on the bottom right of the front of the washing machine. Most machines will have an accessible filter, and the drain pump itself sits behind the filter.
Common Complaints
Regardless of whether a drain pump is blocked or faulty, it will often cause the same symptoms. The most common complaints are all obvious, and all involve wastewater.
Possible Causes of Drain Pump Issues
If the symptoms that you are experiencing suggest that you have a problem with your washing machine’s drain pump, you can start to investigate the problem to determine the best solution.
Why is my washing machine still running water?
There are only two possible causes: either there's something stuck in the drain line or the pump is faulty . You won't be able to tell which it is, however, without looking inside the washing machine, and you do that by removing the front panel. Once you can see what's going on, the next steps you need to take will be apparent.
How to check if a pump is faulty?
If you don't see any, the pump may be blocked or faulty. To check it, you have to disconnect the belt connecting it to the drive motor.
How to remove a drain pump from a washing machine?
Unscrew the screws with a Phillips screwdriver, and remove the panel by tilting it out while you lift it to unhook the top of the panel from the machine. You should see the drain pump attached to the bottom panel. It is connected to the drain hose.
How to tell if a pump is broken?
Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you'll be able to feel them while you're turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
How to get a stuck pump flywheel off?
Reach under the machine and pull the belt off the pump flywheel. It isn't very thick, and you should be able to stretch it enough with your fingers to do remove it. Once the belt is removed, try turning the pump flywheel; it should turn freely. If it doesn't, something probably is stuck inside the pump housing.
What happens if a pump is broken?
If the pump is broken, you'll probably hear sounds when the machine is running. Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since 1975.
Can a washing machine drain if the filter is blocked?
Some manufacturers provide a filter that catches lint before it gets to the pump. The machine won't drain if the filter is blocked. You should be able to access the filter when you remove the front panel.
About Washing Machine Drain Pumps
Common Complaints
- Regardless of whether a drain pump is blocked or faulty, it will often cause the same symptoms. The most common complaints are all obvious, and all involve wastewater. A common complaint is that the water in the washing machine drum will not drain, or that the washing machine has stopped mid-cycle with it still full of water. Another common issue i...
Possible Causes of Drain Pump Issues
- If the symptoms that you are experiencing suggest that you have a problem with your washing machine’s drain pump, you can start to investigate the problem to determine the best solution. Whilst it is possible that the drain pump has failed, there are other issues that could be causing the problem that you are experiencing. As part of your investigation of your drain pump, you sho…