- Lay the Sticker Shield on a clean flat surface with the protective paper side up.
- Lay the EZ Pass transponder on top of the Sticker Shield to mark where to cut it off (about 1/8 inch all around the transponder). ...
- Turn over the piece of Sticker Shield that you cut so the protective paper side is now down.
- The transponder comes with Velcro strips with their own adhesive that you would normally stick onto the windshield, but now you’ll stick them on the shiny side of the piece ...
- Remove the protective paper from the Sticker Shield and you’re ready to go.
- To mount the transponder, remove the transponder from the Velcro strips and place just the Sticker Shield with those strips wherever you want. ...
- Rub the Sticker Shield film firmly to make it smooth and remove any air bubbles. Since it’s carrying the weight of the transponder, make sure it’s attached firmly.
- Finally, press the transponder onto the Velcro strips firmly until it pops.
How to mount or install an EZ Pass correctly?
- The toll rates that are being deducted from your account are higher than they should be based on your enrolled discount plans
- You have received a Notice of Tolls Due (NOTD)
- You have received an “Invalid Tag” message on the patron display
How to install EZ TAG on your windshield?
Find where to install your TxTag.
- Clean. Clean and dry the inside of your windshield. The windshield's temperature must be above 50 degrees Fahrenheit for the TxTag to stick.
- Position. Your TxTag goes on the inside of your windshield behind the rearview mirror. ...
- Stick. Peel off the clear backing on the gray side and stick the gray side to the inside of the windshield. ...
How should you proceed if you lost your EZ Pass?
You should not use your transponder under any of the following circumstances:
- You reported your transponder as lost or stolen, but later find it.
- You are using a different vehicle not registered on your account and have not advised the PTC E-ZPass Customer Service Center of the vehicle change.
- You have an insufficient balance in your account. ...
How to attach EZ Pass?
where should EZ Pass be mounted? Position the transponder on the inside of your windshield, behind the rearview mirror and below any tinting. 4. Place the transponder on the windshield with the E-ZPass logo upright, facing you, and press firmly. Fasten the bumper mount transponder directly to the top of the front license plate holder of your ...
How do you stick E-ZPass to windshield?
Turn the tag right side up facing you. Place the tag in the correct position and press firmly against the glass for 15 seconds to achieve a good bond. Your E-ZPass tag may be removed by gently lifting one corner of the tag to separate the adhesive strips.
How do I get more Velcro for E-ZPass?
Need new adhesive strips? They're FREE! Request them at www.e-zpassny.com or call 1-800-333-TOLL (8655).
How do I install an E-ZPass transponder with suction cups?
0:311:16EZ Pass-Port Suction Cup Windshield Mount Toll Pass Holder - YouTubeYouTubeStart of suggested clipEnd of suggested clipMounting the e-zpass in the holder is simple position the transponder is shown above. And simplyMoreMounting the e-zpass in the holder is simple position the transponder is shown above. And simply push until you hear click attach the mount to any smooth interior surface of your windshield.
How do you shield a toll transponder?
Place the sticker transponder in the lower left-hand corner or lower right-hand corner of the inside of the windshield. Or, place it behind the rearview mirror on the inside of the windshield (Consider visual aesthetics from inside and outside of the vehicle when choosing the location.)
Can you use Command Strips for E-ZPass?
You take one Command Strip in the package, and click it onto another one of the Command Strips in the package. Cut it to size of the transponder's backside.. With them clicked together this way, you have adhesive on each side of the pairing.
Where can I get E-ZPass Velcro for free in PA?
Pennsylvania Turnpike Log in to your E-Pass account and request them for free. We will mailed the mounting strips directly to you. Jennifer Jevack Stueber and 12 others like this. Hi Larry, You will need to contact the PTC E-ZPass Customer Service Center at 1.877.
How do you install a transponder in a car?
0:001:20How to Install a Sticker Transponder - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis new technology requires that the sticker be affixed to the inside of the windshield in orderMoreThis new technology requires that the sticker be affixed to the inside of the windshield in order for the transponder to read. So placing the sticker on the dashboard or in your glovebox.
Does I-PASS need to be on windshield?
The important thing to remember is that to receive the discounted I-PASS rate, your transponder must be properly mounted in your vehicle whenever you drive on the Tollway. In most cars, transponders should be mounted on the windshield.
How to get air bubbles out of windshield?
Since it’s carrying the weight of the transponder, make sure it’s attached firmly. Finally, press the transponder onto the Velcro strips firmly until it pops.
How to mount a transponder?
To mount the transponder, remove the transponder from the Velcro strips and place just the Sticker Shield with those strips wherever you want. Since Sticker Shield can be easily moved around, you can experiment to find the best location. If you stuck the Velcro directly to your windshield, this would be difficult!
Can you keep a transponder on Velcro?
You may want to keep the transponder and the Sticker Shield attached by the Velcro while you carry it around, as a clear Sticker Shield with only two Velcro strips is easy to lose! By the way, Sticker Shield is also good for protecting your transponder from theft. Just remove it and store it out of sight when you park!
How to clean a car mirror?
Sit inside your vehicle facing forward. Select a location behind and to the right of the rearview mirror. The spot should be at least 1″ below the vehicle’s frame and at least 1″ to the right of the rearview mirror, and not within any tinted area. The area should be clean and dry.
What happens if you don't mount your transponder?
You must mount your transponder in accordance with the instructions provided below. If your transponder is not properly mounted, your transponder may not be read, and you may incur a higher toll rate as a result. You will be responsible for paying the higher toll rate. Sit inside your vehicle facing forward.
