Follow these steps in order to resolve the LEr error code on a Traeger:
- Turn the Traeger off and unplug it
- Verify that there are pellets in the hopper If there are no pellets then fill the hopper up
- Remove the grill grate and drip tray
- Slide over the heat baffle to reveal the firepot
- Vacuum out the ash in the firepot
- Put the grill back together
- Clean the RTD temperature sensor with steel wool
How do I fix error code 1 on Traeger?
Apr 08, 2020 · Why is my Traeger not getting hot? Poor airflow in the grill, which can be caused by too much ash buildup in the firepot, rusted holes in the firepot, a tightened chimney cap, a weak induction fan, or the RTD temperature probe inside the …
What to do if your Traeger Grill is not working?
Why is my Traeger not getting hot? Poor airflow in the grill, which can be caused by too much ash buildup in the firepot, rusted holes in the firepot, a tightened chimney cap, a weak induction fan, or the RTD temperature probe inside the grill is dirty or leaning towards the body of the grill.
What does high temperature error mean on Traeger Grill?
How Do I Fix the LEr Code on my Traeger? ... How Do I Reset My Traeger? Here’s how to put one together for use with Traeger Grill: First, click on the menu on Control Panel. Then hold down the IGNITE button until the Traeger logo appears. Now turn off Traeger Grill.
What are the problems with a 1010 Traeger Grill?
There is no specific order or direction the wires need to be inserted. Place the controller back in place and screw in the two Phillips head screws you removed earlier. Plug the grill back in and turn the grill on to see if the code still appears. If the Err or Er1 codes still appear on the controller, please call Customer Service. ER2 Cause
How do I reset the code on my Traeger?
1:173:33HOW TO FIX "HEr" Error Code Traeger Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the easiest and the most obvious fix is just to shut your power off and then just go turn it backMoreSo the easiest and the most obvious fix is just to shut your power off and then just go turn it back to smoke. And see what happens you always want to make sure that you shut the switch off as well.
How do I fix Traeger error?
ResolutionUnplug the grill and remove the two Phillips head screws holding the controller in place.Loosen the flathead brackets holding the RTD wires in the green box.Completely disconnect the RTD wires from the green housing box. ... Reconnect the RTD wires by tightening the flathead brackets.More items...
Why does my Traeger says LEr?
A Low Error Reading of LEr, is an error message you may see on an AC platform Grills (non-WiFIRE enabled) except the 2017 AC Timberline 850/1300. Getting this message means that your grill dropped below 125 degrees for more than 10 minutes and caused the grill to shut off.
How do you reset high temp error on Traeger?
High Temp ErrorClean out the firepot > Place 5-10 pellets back into the firepot > Restart Grill.D2 grills require a "closed-lid start up," meaning you should start your grill with the lid shut. Failure to do so will often result in temperature irregularities through the duration of your cook.
What is HEr code on Traeger?
A HEr error stands for “High Error Reading. '” This usually happens when the grill reaches over 550 degrees and shuts itself off.
How do you reset a Traeger grill?
1:595:22SDSBBQ - How to Restart Your Pellet Grill After You Run Out Of PelletsYouTubeStart of suggested clipEnd of suggested clipTurn it back to shut down give it a few seconds and then turn it back on to smooth and your triggerMoreTurn it back to shut down give it a few seconds and then turn it back on to smooth and your trigger should fire up like.
How do you reset Traeger running out of pellets?
How Do I Reset or Restart My Traeger Grill After I Run out of Pellets?Power off the grill and let it return to room temperature. Remove the grill grates as well as the drip tray. ... Fill the hopper with wood pellets. Switch on the Traeger Grill. ... Reassemble all the pieces once again.
How do you prime auger on a Traeger?
Plug in the grill to an electrical outlet and turn on using the switch on the back of the grill. Add hardwood pellets to the hopper. On your controller, Navigate to Select Auger > Prime Auger. Once pellets begin to fall into the firepot, select Done to turn off the auger.
What is P setting on Traeger?
What Is a P-Setting? The P-Setting, short for Pause Setting, is used on some older grills to help monitor the temperature of the grill when being used in extreme cold or hot temperatures (newer grills monitor this automatically).
Why is my Traeger not getting up to temp?
A Traeger that does not heat up is most likely due to a deteriorated hot rod. The hot rod is the element located at the bottom of the firepot used to ignite the wood pellets and keep the fire burning. Most Traeger hot rods will wear out after a couple of years.
How do you reset the flame on a Traeger?
If the flame goes out, don't reignite the grill again as it is. You need to pull the meat out, let the smoker cool down. Install the fire pot. Restart the smoker and the grill is ready once again.
Err and Er1
The reason you're getting an Err or an Er1 message is because there is a bad connection, or a complete disconnect, between the RTD probe and the control panel.
ER2
An ER2 error message is an indicator that the RTD probe (i.e temperature sensor) has failed.
Why does my traeger fire out?
There are several possible reasons for a fire to go out in a Traeger. Once again, we have to check the fire pot to see if the air holes are blocked . Fire needs oxygen to burn, and without those holes, there’s no oxygen. This is another time where the pellets may be the problem.
How hot should a traeger grill be?
It is totally normal for the temperature inside your Traeger pellet grill to vary by as much as 15-20F above or below the target you’ve set. That’s all part of the regular cycling on and off of the auger and the rod. When it cools down inside, more pellets feed in and ignite. When it’s too warm, they stop for a bit.
What is an automatic auger?
The automatic, rotating auger is supposed to pull pellets from the hopper to the fire pot when the controller says they’re needed . It’s an amazing system – unless it’s not working.
How long does it take for a grill to cool down?
Once the temperature falls below 450F, the auger will run for 2 minutes to clear any embers from the auger tube. Power off the grill and let it rest and then clear any pellets from the fire pot.
Is your grill clean?
Proper cleaning and maintenance of your grill are vital to a successful cook, and excessive ash and grease can very easily affect your grill's ability to read temperature accurately. Please review Grill maintenance for additional details on cleaning instructions.
Was there a fire?
A HEr will happen during a grill fire as the temperature rises above 550. This is normal and to be expected during a grill fire.
Was the grill started correctly?
The correct process for starting your grill will vary depending on your model. Please visit the Start-Up Guide to find your proper start-up procedure.
Was the grill put through the shutdown cycle on the previous cook?
If the grill was not put through the shut down cycle on your previous cook, there might be additional pellets in the firepot from your last cook, which can cause the temp to spike.
Did you receive a LEr on your previous cook?
If you received a LEr (Low Error Reading) message during your previous cook, and this is your first time starting your grill since then, you might get a HEr message. This can happen as the grill tries to burn off any additional pellets built up during the last cook.
Are the internal parts of the grill installed?
HEr messages can occur when the insides of the grill are not in place (drip tray, heat baffle, grill grates).
Is the grill reading temperature accurately?
Ensure the grill is reading the temperature accurately. To check this, follow the steps below.
How long does it take for a traeger grill to heat up?
The most common problem of Traeger grill is its unusual heat swings.Sometimes it takes a long time to heat up.Depending on outside temperature the grill takes 5 or 10 minutes to heat up. When you use your Traeger for the first time it will take approximately 7 minutes.
Why is my induction fan not working?
It happens for a number of reasons. Firstly, this can be happened for the lack of power from the controller to the orange wires. Lastly , similar obstructions can restrain the fan from spinning. Solution.
Does a traeger grill need electricity?
Charcoal or gas grill does not require power to on but Traeger grill require power to on. It is a common and simple problem for the user. Ultimate components like induction fan and auger motor need electricity to work and make your BBQ alluring.
Does a Traeger grill smoke?
It is a vital complaint about Traeger Grill that sometimes the grill is not smoking. The main purpose of a grill is to smoke. But when the grill halt to smoke then it turns into a major problem.
Do you have to stand beside a traeger grill?
You don’t have to stand beside the grill and keep adding pellets constantly because the Traeger grill comes with an automated auger and hopper that can do the work for you. But many grilling lover persons face this problem that the pellets not moving from the hopper to the fire pot.
