How do I fix my PetSafe collar?
- Remove the receiver collar from your pet.
- Remove the battery from the receiver collar.
- At the transmitter, move the boundary switch from the low to the high position.
- Slowly adjust the boundary control dial up to #8, down to #1 and then back to the #4 position.
Full Answer
What to do when your dog’s collar is not working?
Start by checking the batteries. You can replace them if they are not working as expected. However, the issue can also happen in reverse, whereby the pet’s safety is compromised because the impact of the fence is too strong. In such cases, it is advisable to set the collar at a minimum level and consider applying minimum corrective measures.
How to put a dog collar on a fence?
To add the collar to the fence, consider doing this during the training period. You need to place the receiver collar on the pet’s neck. Alternatively, hold the collar close enough so that the pet hears the beeping of the collar during training.
How to use a receiver collar for dogs?
You need to place the receiver collar on the pet’s neck. Alternatively, hold the collar close enough so that the pet hears the beeping of the collar during training.
How do I adjust the static correction on my Dog's Collar?
There is always a solution for every dog, no matter how stubborn or playful they are. To adjust the collar and set the static correction for such a dog, increase the static correction level by pressing and releasing the correction level button. This should happen within the first 5 seconds of the past series of flashes.
Why is my PetSafe collar not working?
If Receiver Collar does not beep and the Test Light does not flash, replace the 10. battery in the Receiver Collar. If it still does not beep and the Test Light does not flash, contact the Customer Care Center at 1-800-732-2677. If the Receiver Collar beeps, there may be a complete or partial break in the 11.
How do I reset my PetSafe wireless fence collar?
Make sure the collar is powered on. Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on. Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off.
Why is my PetSafe collar beeping but not shocking?
Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.Aug 13, 2020
How long do PetSafe wireless collars last?
The Wireless Containment System unit can last up to approximately 10 years or more if used properly. Batteries on the collar can last and be replaced up to 1 to 2 months.
How do I reset my petsafe bark collar?
Turn the battery to the OFF position using a coin. Wait 10 seconds. Turn the battery to the ON position. The collar light will turn solid green, then solid orange for two seconds.
How do I test my petsafe collar?
All you have to do is hold the tool against the contact points on your dog or cat's receiver collar to check if the collar is working properly. The test light tool will light up if static correction is being activated. This accessory comes in most kits including a fence receiver collar, remote trainer, or bark collar.
Why is petsafe collar blinking?
The Receiver Collar is equipped to automatically increase the level of Static Correction the longer your pet remains in the Static Correction Zone if the collar is set at level 2 or above. The Receiver LED Indicator Light acts as a low battery indicator, flashing every 4 to 5 seconds when replacement is required.
How do you reset an electric dog collar?
Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin flashing as normal.
How do I change the battery in my petsafe collar?
0:000:29How To Change The Battery PetSafe Wireless Pet Containment System ...YouTubeStart of suggested clipEnd of suggested clipRight here. And you're going to line them up with the grooves inside here and put in a new batteryMoreRight here. And you're going to line them up with the grooves inside here and put in a new battery it's very simple.
Does PetSafe collar turn off?
The Safety Shut Off feature automatically turns the collar off for three minutes if your dog barks more than 15 times within an 80 second period. CRefrain from having your dog wear the collar longer than 12 hours to avoid skin irritation. Water resistant, not submersible. Intended for dogs six months or older.
How do I sync my PetSafe collar to my transmitter?
How do I sync my PetSafe collar to my transmitter?Remove your pet's receiver collar.Remove the Battery from the Receiver Collar.Move the limit switch of the transmitter from the lower position to the upper position.Slowly set the limit switch to # 8, down to # 1, then return to position # 4.Apr 28, 2020
Can PetSafe wireless collar get wet?
It's water resistant! Can get wet but not submerged long.. we have a pond on property and I set the distance so he can only put his feet in then he gets the audible. Keeps him out when we are not home.
Why is my PetSafe transmitter not working?
Whenever you suspect that something could be amiss, it is advisable to take the collar’s battery out for a few minutes before returning it. If it is still faulty, replace it with a new battery, ensuring to install it properly.
How to add a receiver collar to a fence?
To add the collar to the fence, consider doing this during the training period. You need to place the receiver collar on the pet’s neck. Alternatively, hold the collar close enough so that the pet hears the beeping of the collar during training.
How to tell if a fence is amiss?
The first sign to hint that something is amiss is when the fence fails to deliver as expected, and the dogs can easily go beyond the restricted area . When this happens, there is a need to assess and find a solution to the issue.
Why does my dog wander away from the boundary?
When the connection is right, some vibrations occur in the animal’s neck area, preventing it from crossing the boundary. When the vibrations/shock fails, the animal can wander away beyond its safe area. If you notice this happening frequently, then check the issue that could be resulting from it.
Can you use a vibrator collar on a deaf dog?
In case you won a deaf dog and would still love to use your PetSafe fence effectively , then you need to choose a fence with a vibrator collar. The collar can be specially adjusted to replace the beeping sound with mild vibrations.
Can you replace a dog collar if it is not working?
You can replace them if they are not working as expected. However, the issue can also happen in reverse, whereby the pet’s safety is compromised because the impact of the fence is too strong. In such cases, it is advisable to set the collar at a minimum level and consider applying minimum corrective measures.
Do PetSafe fences come with warranties?
Note that most PetSafe fences come with warranties and quality assurances that are meant to assure users. You may need to apply this in case all attempts to get the collar working fail. However, you should only resort to changing the collar after failed attempts of increasing shock vibration levels.
