How to Fix the F-28 Code on a Whirlpool Duet
- Unplug the electrical cord from the wall outlet.
- Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
- Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
- Find the control console unit reset lever and pull it toward you.
- Replace the detergent tray and secure it with the screws you removed. Plug the electrical cord back int the outlet.
How to repair my Whirlpool duet washer?
How do I fix my f28 error on my Whirlpool Duet washer?
- Unplug the electrical cord from the wall outlet.
- Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
- Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
- Find the control console unit reset lever and pull it toward you.
How to clear Whirlpool duet error?
- Write the error code down so you won't forget it after it is cleared.
- Press the "Pause/Cancel" button on the control panel twice to clear the error.
- Contact a certified repair technician if pressing the "Pause/Cancel" button does not clear the error, as this indicates that a component has failed in the washing machine or dryer. ...
How to unlock a whirlpool duet washing machine?
- Locate the "Control Lock/Unlock" button on your Duet's control panel.
- Press and hold the "Control Lock/Unlock" button for three seconds.
- Release the "Control Lock/Unlock" button when the control lock icon on the display disappears.
Why is my Whirlpool duet dryer not heating?
Whirlpool Gas Dryer Not Heating
- Ignitor is Burnt. Electrical current flows through the ignitor on a gas dryer. ...
- Defective flame sensor. Your gas dryer is also equipped with a flame sensor that ensures the flame burns inside the flame chamber.
- Malfunctioning gas valve. If your Whirlpool dryer doesn’t heat or only heats intermittently, the coils may be defective. ...
- Blown thermal fuse. ...
How do I reset my Whirlpool Duet washer?
Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does F28 mean on my washer?
central control unitshantapanchu a F28 error code is a common problem indicating that there is a communication problem with the central control unit. Any error code can be caused by a electrical anomaly. try to reset your washer.01-Aug-2017
How do you clear the error code on a Whirlpool Duet washer?
0:462:03Whirlpool Duet Washer Diagnostics & Error Codes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you've reached the last saved fault code you will hear three beeps. You can clear the codesMoreOnce you've reached the last saved fault code you will hear three beeps. You can clear the codes from the washers memory by pressing and holding the third button again for five seconds.
Why does my washer say F 28?
F28 means that your main central control board (CCU) and the motor control board (MCU) are not communicating with one another properly. You will need to check all the connections at both boards, the mcu is in the bottom of the washer and the ccu is mounted at the top inside of the washer on the right side.
What does F28 mean on a?
Vaillant officially defines the F28 error code as an ignition fault. There are many potential causes to this problem including an insufficient supply of gas, a faulty electrode or ignition lead. Therefore, the causes of the F28 fault can be broadly categorised into either an ignition fault or a gas valve fault.
What is a F21 error on Whirlpool washer?
If your Whirlpool washer has an F21 error code, it indicates that your washer has a drainage problem. The good news is the issue can usually be resolved by simply clearing the drain filter or drain hose.04-Oct-2021
What does F24 mean on Whirlpool washer?
The F24 error is a water temperature sensor error. It means the water temperature sensor value being sent to the main control board was out of range when the washer was in the part of the cycle that heats the water. This error is most commony caused by a failed water temperature sensor otherwise know as the NTC sensor.
What does F05 mean on a Whirlpool washing machine?
Waste pipe blockageF05 — Waste pipe blockage or pump issue. Issue: Washing Machines door will not open / the door can be opened but water remains inside the drum.
What is F02 code on a Whirlpool washer?
The F02 error code on a Whirlpool washer indicates that the control detects a long drain time. This can be caused by excessive suds in the tub, a restriction or clog in the drain system, or by a number of other component failures.06-Mar-2016
How do I fix the code F28 on my Kenmore washer?
Press the "Stop" button twice. ... Press the "Rinse/Drain & Spin" button on the control panel to drain the washer and spin any remaining water out of the tub and clothes.Pull the washer door open and close it to reset the appliance. ... Open the detergent dispenser drawer on the left front side of the washer.More items...
What does a flashing F mean on a Whirlpool Duet washer?
The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won't run at all.
What does F28 mean on a Maytag 3000 Series washer?
Error Code F28: Problem with Serial Communication When this Maytag error code is displayed, the washer will be unresponsive. This suggests that there is a problem with serial communication between MCU and the CCU.
The Dreaded Whirlpool Duet F28 Error Code
In layman’s terms, an F28 error code means there’s a serial communication error between some parts in your Whirlpool Duet Sport washer.
How to Fix the Whirlpool Washer F28 Error
As we said before, the F28 error isn’t a big deal in almost all cases.
Final Thoughts
This is it for our overview on the Whirlpool F28 error. To recap, this error means there’s a connection error between the CCU and the MCU, which can happen because of an electric mishap or loose connections in your washing machine.
Step 2
Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
Step 3
Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
Step 5
Replace the detergent tray and secure it with the screws you removed. Plug the electrical cord back int the outlet.
