how do i disconnect my throttle cable

How do I disconnect my throttle cable?

• Step 1: Locate the throttle cable.
• Step 1: Disconnect the throttle cable at the throttle body.
• Step 2: Disconnect the throttle cable from the retaining bracket.
• Step 3: Pull the throttle cable through the firewall.
• Step 4: Disconnecting the throttle cable from the accelerator pedal.

Full Answer

How do you remove throttle cable from handlebars?

1:406:29How to remove a throttle tube and put it back on - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way to do this is to pick the housing up and just pull the housing. Against the cable.MoreThe easiest way to do this is to pick the housing up and just pull the housing. Against the cable.

How do you remove a GM throttle cable?

Removing the Accelerator CableRaise the hood of your GMC vehicle and prop it open. ... Disconnect the accelerator cable from where it connects to the throttle body, using a pair of pliers. ... Remove the cable from the routing retainers. ... Remove the cable by pushing it through the firewall and into the engine compartment.

How do I remove a throttle cable from a carburetor?

1:5311:33How To Replace a 2 Stroke Throttle Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide that the throttle cable is attached to now to do that we need to gain access to these twoMoreSlide that the throttle cable is attached to now to do that we need to gain access to these two screws that are on the top of the carburetor now to do that we need to loosen. These clamps right here.

How do you remove a throttle body?

2:5411:29How To Clean a Throttle Body ~ The RIGHT Way - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemember pull the tab. Push. It in to the component. And then remove it the throttle body itself isMoreRemember pull the tab. Push. It in to the component. And then remove it the throttle body itself is held in with four bolts for this. Particular. One I like to use a ball head Allen.

Why do you have to add a small section of cable between the two ends of a throttle?

Since the wire is snapped in half, you will lose some of its length by reattaching it. So, you have to add a small section of cable between both ends so that the throttle will work correctly. It doesn’t matter which side you start on (controller or engine), so pick the most comfortable one.

What to do if throttle line snapped?

Second, if the line has snapped, you can use aluminum crimps to reattach the pieces. Finally, if the problem is rust or debris clogging the throttle control, you can simply clean it out. Here’s a step-by-step breakdown for each option.

How to measure new wire for throttle?

When measuring the new wire, be sure to allow for some slack between the bracket and the controller. This slack is necessary so that you can pull the lever back without being too tight. Then, make a mark to cut the cable where it meets the front of the engine. If you’re unsure where that is, find the throttle arm and measure a few inches beyond that. You can always cut the line shorter, but you can’t add more once it’s gone.

How to make a z-shaped bend in a throttle arm?

Using pliers, you want to make a z-shaped bend in the tip. This will allow you to move the throttle arm easily. Don’t make the angle too deep, or it won’t fit. From there, you can insert it into the hole so that it won’t come loose on its own.

Why are throttle cables so long?

So, you will have to measure the length to ensure that it will work for your machine. If it’s too long (or short), you won’t be able to close the throttle completely, which can be a hassle to have to do it by hand.

What is the throttle on a lawn mower?

This piece controls the speed of the engine and the blades. You always want to mow at full throttle to make your lawnmower more efficient.

What to do if cable is gummed up?

Alternatively, if the cable connections are simply gummed up, you can use penetrating oil to clean them out, and it should start working again.