How do I change the battery in my Cateye Opticube? Cateye equips the light with a Drop-Out lock mechanism so you may remove the light from the mount when leaving the bicycle locked up. Unscrew the back battery housing panel and insert the three AAA batteries into the housing.
Full Answer
What is a Cateye OptiCube bike light?
The Cateye Opticube is a handlebar-mounting bicycle light that uses a white LED bulb. The unit takes three AAA batteries and the company claims these will last up to 60 hours. There are three settings to the light, with a bright, a midlevel and a blinker light. The Opticube is made to go onto the handlebar with no tools needed.
How do you install a Cateye OptiCube light?
The Cateye Opticube is a handlebar-mounting bicycle light that uses a white LED bulb. The Opticube is made to go onto the handlebar with no tools needed. Unscrew the back battery housing panel and insert the three AAA batteries into the housing. Screw the panel back on and undo the ratchet strap completely.
How do I replace the battery of my Cateye sensor?
* Press the top edge of waterproof inner cap to remove it. Install the cap with the “ TOP ” faced upward. * After replacing the battery, press AC on the back of the computer. (Restart operation) If using a CATEYE sensor, the values related to the sensor's battery replacement period start flashing to indicate that it is time to replace the battery.
How do I install the OptiCube on my bike?
The Opticube is made to go onto the handlebar with no tools needed. Cateye equips the light with a Drop-Out lock mechanism so you may remove the light from the mount when leaving the bicycle locked up. Unscrew the back battery housing panel and insert the three AAA batteries into the housing.
How do I change the battery in my Cateye bike light?
Press and hold Attach securely in the mounting position. Use a coin to pull out the inner unit. Install batteries according to the marks on the inner unit, and put back the unit in the light body securely.
How do you charge a Cateye Opticube?
Connect the light unit to your PC or a commercial USB battery charger using the USB cable. ( 1 – 2 ) The switch lights up, and charging starts. * When your PC is in sleep state, the unit cannot be charged. * Use a USB battery charger of 500mAh (USB2.
How do you open Cateye bike lights?
To remove the light unit, pull out it forward * while pressing the button. To re-adjust the beam angle, loosen the dial * enough to move the bracket, and securely tighten it after adjustment. CAUTION!: Be sure to tighten the dial by hand. When • you tighten it too hard with a tool, the screw thread may be stripped.
How do I change the battery on my rear bike light?
0:010:38Quick Tip #3 - How to Change the Batteries in your Rear LightYouTubeStart of suggested clipEnd of suggested clipFirst. And you'll often find a little groove there which is perfectly shaped to accommodate a coinMoreFirst. And you'll often find a little groove there which is perfectly shaped to accommodate a coin such as a 10-cent piece which you can slip in the side give it a quick twist.
How do you charge USB bike lights?
Product description Attach the micro USB cable to the Bike Light's micro USB input port. Insert the other end of the cable into either an AC adapter (not included) connected to a wall socket or an active computer USB port. The LED Indicator will turn to be green when the Bike Light is fully charged.
How long do cat eye lights take to charge?
11 hours Flash : Approx. 60 hours * Average runtime at 20˚C. * The specifications and design are subject to change without notice. CatEye products are warranted to be free of defects from materials and workmanship for a period of 2 years from original purchase.
How do you turn off a Cateye?
From the measurement screen, press MENU to switch to the menu screen. Measurement screen. ... Press MODE to display the screen shown below, and then press MODE for 2 seconds. (2 seconds) ... Switch off the functions you want to skip by moving to the relevant icon and turning the setting off. ... Press MENU to confirm settings.
How do I get rid of Cateye?
This is how I do it. Place the pad of your thumb on the lowest of the bottom of the Cateye computer , apply firm direct pressure away from the bracket. don't worry it alright its going to take some pressure to release it but push with your thumb away and toward the front of your bike and it will resease.
How do you open an LED battery compartment?
0:511:35Battery replacement for rgb led remote - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo there you go to lift up the battery so again you want to push this in. And then pull up and makeMoreSo there you go to lift up the battery so again you want to push this in. And then pull up and make sure that the plus is on the top for your remote control.
How do you open a bike light?
0:000:32Planet Bike Blinky 3 battery replacement tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm going to stick a coin flat head screwdriver I'm using a washer stick. It in that slot twist. PopMoreI'm going to stick a coin flat head screwdriver I'm using a washer stick. It in that slot twist. Pop it right open.
How do you change the battery in a Nathan strobe light?
Battery compartment is a little tricky but light works great after replacing the battery's. Just use a quarter on the end of the light twisted sideways and pop the compartment open. Do it over a towel at your dining table because the battery's pop out.
How to attach Opticube light to handlebars?
Place the Opticube onto the center of the handlebars - to the left or right of the stem. Bring the strap under the bars and marry the two strap ends together so the end sticks out of the black ratchet locking device. Pull and down on the ratchet to tighten the strap thus securing the light to the handlebars.
How long does a Cateye Opticube last?
The unit takes three AAA batteries and the company claims these will last up to 60 hours. There are three settings to the light, with a bright, a midlevel and a blinker light.
How to get a light out of a bike?
Pull and down on the ratchet to tighten the strap thus securing the light to the handlebars. Press the rear Drop-Out button to pop the front of the light free. Pull up and out to remove the light from the mount, or back and down to snap it back onto the mount.