- Erase the old PIN. Press and hold the Arrows button, the number 6 button and the "Prog" button. ...
- Program the new PIN. Press numbers 1, 2, 3 and then the "Prog" button in that order. ...
- Enter your new PIN. It should be a three- to four-digit code. ...
- Test the door operation.
How do I use the Genie Intellicode keypad?
Part 1 Open the Genie Intellicode keypad cover halfway. Keep the cover open, and enter 3, 5, and 7 on the keypad. Enter your personal identification number (PIN). PRess the PROG key. Close the cover fully, and progress to Part 2.
How do I program my Genie hardwired keyless entry pad (kep1)?
Programming Genie Hardwired Keyless Entry Pads (KEP1) (This keypad has no cover and is connected to the inside receiver by a special ribbon.) 1 Slide switch on box in garage to Program. 2 Press ENTER, then put in your own code ( up to 6 digits) and press ENTER again. 3 Slide switch on box in garage to OPERATE. Test keypad.
How do I program my Intellicode wireless keypad?
To Program the Intellicode Wireless Keypad Open cover fully by sliding keypad cover up until it latches. Press 3-5-7. Press “PROG”. Enter your Personal Identification Number (PIN). Press “PROG”. Close cover fully. Proceed to Part 2 below.
How do I program my keypad to my Intellicode/CodeDodger garage door opener?
Your keypad is now ready to be programmed to the garage door opener. Locate the Learn code button on your Intellicode/CodeDodger garage door opener. Depending on model, the learn code button will be located under the light cover or on the rear panel. Press the learn code button.
How do I reset my Genie garage door keypad without a PIN?
Press and hold both the Program key and the Up/Down key for about 5 seconds. The LED will slowly blink and then go out. When the LED goes out, you have successfully erased the old programming.
How do I reprogram my garage PIN pad?
0:031:20How to Reset a Garage Door Keypad Outside - YouTubeYouTubeStart of suggested clipEnd of suggested clipCode you want followed by enter. And kind of hold down enter for a sec or two and then let go thenMoreCode you want followed by enter. And kind of hold down enter for a sec or two and then let go then the next time you hit enter.
How do I reprogram my Genie garage door opener?
1:352:35Genie Remote Control Programming (Full video) - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress and hold the square program set button until the round LED. Light turns blue.MorePress and hold the square program set button until the round LED. Light turns blue.
How do you recode a garage door opener?
At the opener, press and hold Program until the LEDs goes on. Release and one LED should remain lit. To get to the programming menu, press and release the Program button again and the LED should start flashing. Pick up your remote or clicker and press the button already programmed to the opener.
Community Q&A
Include your email address to get a message when this question is answered.
Warnings
Visibly check the area below the garage door before pressing the Up/Down button.
About This Article
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 71,372 times.
What is a pin on a keypad?
The keypad can also be wireless. A PIN number (Personal Identification Number) is used to identify authorized access , and the keypad needs to be programmed to recognize that number. PIN codes can be added and changed as necessary. Change the PIN anytime you think privacy may be compromised. Advertisement.
How to use a temporary pin in a garage?
A temporary PIN allows access to the garage by guests or workers. Enter your PIN and then press “Prog” three times. Enter the temporary PIN and then press “Prog.”. The temporary PIN will be useable until the next time you enter your own PIN.
Where is the code button on a Genie garage door opener?
This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head. When pressed, a radio signal indicator will start blinking red for 30 seconds.
What frequency does a Genie garage door opener work on?
Keypad is black with a slide-up cover showing the Genie logo only) This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below).
What is Intellicode 2?
Intellicode 1 refers to all systems made from 1995 to Present, with the exception of 2011 and 2012. Intellicode 2 refers to most units made in 2011 and 2012.
How to program a Genie keypad?
Part 1. Open the Genie Intellicode keypad cover halfway. Press the PROG and 8 buttons simultaneously, and hold them down. The indicator light should blink once, alerting you that your wireless keypad is ready to be programmed. Keep the cover open, and enter 3, 5, and 7 on the keypad. Press the PROG button, and watch for ...
Where is the code button on a Genie garage door opener?
This small black button is located behind the light bulb cover, near the antenna wire that protrudes from the unit. When pressed, a radio signal indicator will start blinking red for 30 seconds.
What is Intellicode keypad model 2?
Intellicode Keypad Model #2. Type 2 keypads are white with a flip-up cover. Image Credit: Genie. Type 2 keypads are white, with a flip-up cover. This is model GWKP. There are two sets of steps to programming a new code into this type.
What is a wireless garage door opener?
Wireless keypads allow convenient access to a garage. The Genie Intellicode garage door opener system includes both portable remote controls and also keypad controls that may be mounted on an exterior wall of your garage.
How many models of Intellicode keypads are there?
There are three models of Intellicode keypad, and they may have different methods of programming depending on what version of Intellicode door opener is mounted in your garage. Read the following instructions carefully to determine which instructions apply to you. Advertisement.
What is the model 3 keypad?
The model #3 keypad is the GK-BX, which will work with Genie systems using either type 1, type 2, or type 3 controls. Intellicode 1 refers to all systems made from 1995 to the present, with the exception of 2011 and 2012. Intellicode 2 refers to most units made in 2011 and 2012.
What is the word on the keypad on a Model 1?
Model 1 keypads are black with a sliding panel. Model 1 keypads will be black with a slide-up cover and will have the word "Intellicode" printed on the cover. They include opener models GWKIC and ACSDG. There is a two-part process for programming a new code.
