How to perform an idle relearn procedure Honda
- Turn off all electrical items like A/C, audio, lights, etc.
- Reset the ECM/PCM with a scan tool.
- Turn the ignition switch to ON (position II), and wait 2 seconds.
- Start the engine and rev the engine until you reach 3,000 RPM without any load (A/T in P or N, M/T in neutral). ...
- Let the engine idle for about 5 minutes with the throttle fully closed.
What is the idle relearn procedure on a 2009 Honda Accord?
You must perform an idle relearn procedure Honda any time you replace the ECM/PCM, reset the ECM/PCM, update the ECM/PCM, replace or clean the throttle body, or disassemble the engine or the transmission. This procedure applies to all 2009 Honda Accord 4-cyl and 6-cyl vehicles and many other Honda products.
What is the idle learn procedure?
The idle learn procedure is for the dealer to use after a service call so the customer doesn't turn around and come right back in because he noticed slightly irregular idle. In a couple miles it will learn your driving habits and adjust itself.
How do you reset the throttle body on a Honda?
Shops perform a Honda throttle body reset with a scan tool, but you can perform it manually by following this procedure: 1) Turn the ignition key to the RUN position for 2-seconds. Do not start the engine. 2) Start the engine and run it at 3,000 RPM until the radiator fans come on.
How long should I let my engine idle to cool off?
Continue revving until the radiator fan comes on, or until the engine coolant temperature reaches 194 °F. If the radiator fan comes on, do not include its running time in the 5 minutes. Let the engine idle for about 5 minutes with the throttle fully closed. Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period.
How do I reset my Honda idle?
Here are the steps you'll need to follow to reset the idle air control (IAC) valve in your Honda:First, push the accelerator pedal in slightly.Once you've done that, start your engine and let it run for five seconds.Turn the ignition off for ten more seconds.Once 10 seconds have passed, restart the engine.
How can I make my car idle relearn?
0:403:27Idle Relearn Procedure After Battery Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat you have to do is circle. The key twice. Before so it's in the off position right you circleMoreWhat you have to do is circle. The key twice. Before so it's in the off position right you circle the key. Once twice and then you put your foot on the brake. And then you start the car.
How do you reset a Honda throttle body?
Follow these steps:Connect your scanner to the OBD2 port under your dash.Use the buttons on the scanner to navigate to the TP POSITION CHECK menu.Reset the TP value.Select RELEARN PROCESS after the TP value has been reset.
How do I adjust my Honda idle?
Pry the plastic cap off if it is still engaged. Disconnect the idle air adjustment valve by locating and disengaging the electronic connector that holds it to the throttle body. Turn the idle screw to adjust the idle—turn the screw to the left to increase the RPM or to the right to lower it.
Will disconnecting battery reset idle?
0:261:17“reset idle” after disconnecting battery terminal (toyota camry) EASY FIX ...YouTubeStart of suggested clipEnd of suggested clipAnd start taking everything off your car just bring the rpms up and just let it relearn what itMoreAnd start taking everything off your car just bring the rpms up and just let it relearn what it needs to relearn. After about five minutes your idol will be reset. Thanks for watching.
How do you relearn a procedure?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll need to perform a relearn procedure on the PCM. Here's how you do it start. And idle theMoreSo you'll need to perform a relearn procedure on the PCM. Here's how you do it start. And idle the engine in Park for 3 minutes initially. You may notice a higher incorrect idle speed until the ECM.
How do you calibrate a Honda TPS?
1:544:19How to replace / calibrate your throttle position sensor TPS (Honda)YouTubeStart of suggested clipEnd of suggested clipYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to theMoreYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to the negative lead of the battery. And the positive lead should be connected to the little red wire.
Will disconnecting battery reset throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do you reprogram a throttle body sensor?
1:082:42Throttle Body Relearn: When Should I Reprogram My Car's ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
What is idle learn procedure?
The idle learn procedure is for the dealer to use after a service call so the customer doesn't turn around and come right back in because he noticed slightly irregular idle.
How to cool a 98 Ford Mustang?
1. Make sure all electrical items (A/C, audio, rear defogger, lights,etc.) are off. 2. Start the engine, and hold it at 3,000 rpm with no load (in park or neutral) until the radiator fan comes on, or until the engine coolant temperature reaches 194 degrees F (90 degrees C).
What is idle learn?
The idle learn procedure is for issues with problem idle components, IE mas air flow sensor, throttle body, i.a.c. valve, etc... when these go bad and need to be cleaned or replaced your pilot will most likely run awful or not at all once the problem is solved. This is because they are smart (the cars) and learn to compensate as best they can when the part is not feeding information it likes. Just replacing a battery won't usually cause the ECM to have created trim levels that are no longer helpful because there was an inop part in the air side of the manifold. Even a vacuum leak can wreak havoc on the poor thing. And this information is never put in an owner's manual because a large portion of drivers have no desire or chance at figuring any of this out and would be more dangerous than anything armed with technical information about their vehicle ? if your car idles and runs fine don't touch it. It will not cost you mileage as I said these are smart cars and are constantly operating as efficiently as possible with the information the sensors are feeding it. Peace
How much power does a cylinder make at full throttle?
Each cylinder is being fed some infinitesimally small amount of fuel so it can make 0.1% of the power it would make if it were running at full throttle. This makes individual cylinder-to-cylinder variations and tolerances that wouldn't be noticed at 10% throttle quite noticeable at 0.1% throttle.
How does an idle air bypass valve work?
To provide air at idle, carmakers installed an idle air bypass valve that allowed air to flow around the closed throttle plate. The fuel injectors provided the fuel and the bypass valve regulated airflow. But electronic throttle bodies don’t have an idle air bypass valve, and they don’t use a throttle cable. Instead, these are “fly by wire”.
Why does my Honda throttle body have carbon?
All electronic throttle bodies accumulate carbon buildup on the throttle plate and bore—the Honda throttle body is no exception. The carbon accumulates after the engine is shut down and is caused by hot oil and gas vapors rising to the top of the engine where they collect on the cooler throttle body.
How to clean throttle body?
Once off the engine, set the throttle body on a clean shop rag with the electronics facing up. Slowly open the throttle plate and begin cleaning by spraying the aerosol cleaner on a clean soft rag and wiping the solvent onto the throttle plate and throttle bore. NEVER spray the solvent directly onto the throttle plate.
Why don't you need to clean your throttle body?
You don’t need routine throttle body cleaning because your car’s computer is designed to adapt to normal carbon buildup issues. Pay for induction cleaning ONLY when you’ve got a performance issue like a rough idle or stumble on acceleration.
What is throttle plate opening?
throttle plate opening, it expects a certain amount of air to flow between the throttle plate and throttle bore. But as carbon builds up and reduces that space, the engine becomes air starved. The computer can detect the lower airflow based on inputs from the mass airflow sensor and commands an even larger throttle plate opening.
Can you spray throttle body cleaner on a throttle body?
Also, never use abrasive scrubbing pads or brushes to remove the carbon buildup. Never spray throttle body cleaner into an electronic throttle body while it’s still on the engine.
Can you use a spray cleaner on an electronic throttle body?
You can’t use that technique with an electronic throttle body, because the spray cleaner can flow along the throttle plate shaft and into the motor housing and circuit board areas, causing complete failure. Shops sell routine induction service as a way to boost profits. That’s a scam.