Receiving Helpdesk

gm throttle body relearn

by Lora Hamill Published 3 years ago Updated 2 years ago

Part of a video titled GM Truck Electronic Throttle Body (ETB) Relearn Procedure
0:32
2:05
Next turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.

How do you reset the throttle body on a GM?

Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds.

How do you reset the throttle body sensor on a GMC?

The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.

How do you recalibrate a throttle body?

0:093:26Throttle Calibration- Relearn? Car Feels Different - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut your car in the run. Position. Once everything is good press down on the gas. And hold it downMorePut your car in the run. Position. Once everything is good press down on the gas. And hold it down for 20 seconds slowly let off the gas. Okay then put the car in the off.

How do I relearn idle?

Follow these steps to complete an Idle Relearn: Run the engine until it reaches normal operating temperature. Allow engine to idle for at least one minute. Turn the air conditioning on and allow the engine to idle for at least one minute. Release the parking brake.

How do you calibrate a throttle position sensor?

1:544:19How to replace / calibrate your throttle position sensor TPS (Honda)YouTubeStart of suggested clipEnd of suggested clipYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to theMoreYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to the negative lead of the battery. And the positive lead should be connected to the little red wire.

How do I reset my throttle body idle?

Turn the ignition switch on and wait 3 seconds. Immediately after the 3 seconds, the accelerator pedal must be pressed and released 5 times within 5 seconds. Wait 7 seconds and fully press the accelerator pedal and hold for approximately 20 seconds until the check engine light stops blinking and stays on.

How do I calibrate my accelerator pedal position sensor GM?

To recalibrate the ECM and accelerator pedal, the ignition switch must be in the ON position and then the accelerator pedal must be slowly and fully depressed from idle to full throttle. Repeat the procedure three times.

What happens if TPS is not calibrated?

If your TPS is faulty or uncalibrated, the sensor will be unable to accurately determine the position of the sensor. This will lead to a variety of symptoms, all of which are caused by the fact that the ECM is delivering the wrong air/fuel ratio to the cylinders thanks to the bad sensor.29-Oct-2021

How do you adjust the throttle position sensor on a Chevy?

0:573:47TPS or Throttle Position Sensor Adjustment 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idleMoreBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idle speed. And then readjusting the TPS. The desired idle condition can always be met by the engine.

What is the relearn procedure?

The three types of relearn procedures are auto relearn, stationary (manual) and OBD. Some vehicles may use a combination of two or more relearn types. Indirect TPMS systems use an initialization procedure which may require a TPMS tool to figure out the steps involved to reset the system.23-Mar-2018

Is idle relearn necessary?

Engine idle is only part of the natural memory, or accumulated data, lost when the battery is replaced. Adjustments to the fuel mixture, transmission shifting and various habits of the driver may all have to be relearned.

What to do after cleaning a GM throttle body?

After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn. After cleaning the throttle body on a GM vehicle, you may need to perform a throttle/idle relearn.

Can you throttle relearn without a scan tool?

Throttle relearn can also be done without a scan tool, essentially by letting the vehicle idle in park for several minutes and allowing time for the ECM to learn. See appropriate service information for vehicle specific procedures and details if you wish to perform a throttle relearn in this way. Information provided by Mac Tools.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9