gm plastic fuel line repair

by Joana Emard Published 3 years ago Updated 3 years ago

How to fix leaking fuel lines?

Mar 23, 2018 · This video will show you how to fix your broken plastic (nylon) Fuel lines found on most General Motors products like the Chevy Silverado GMC sierra Chevy Ta...

How to repair fuel lines?

Mar 15, 2018 · So this video shows you how to repair the insides of a GM plastic fuel line that has came apart during the removal process if you had a rusted fuel line ther...

How much for fuel line replacement?

SET-RB800058-2 Fuel Line - Black, Plastic, Fuel Line, Direct Fit, Set of 2. Part Number: SET-RB800058-2. Vehicle Info Required to Guarantee Fit. $36.99. +$0.00. Core Charge. Add to cart. Product Details. Location : Outlet, Inlet, Inlet Or Outlet Notes : Contains (2) Fuel Line; Viton gasket material; 3/8 in. fitting size end 1 and 2; Straight ...

How do you repair a fuel line on a car?

Nylon line repair kit 2000-2003. The connectors on the preformed nylon line between the fuel line and fuel tank sending unit will seize sometimes from rusty fuel lines. This kit will attach to your existing nylon line and the new connector will attach to the new fuel line. Please note: When cutting nylon line ensure cut is clean (no spurs or rough edges) and straight across.

How do you fix a broken plastic fuel line?

1:564:24BEST ways to repair dorman nylon plastic fuel line tubing - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey're gonna seal these compression fittings work really good with this nylon gas line and you justMoreThey're gonna seal these compression fittings work really good with this nylon gas line and you just pop it right off by pushing the blue washer.

How do you join plastic fuel lines?

3:227:27Repairing Damaged Fuel Lines with BrakeQuip - Gear Up With Gregg'sYouTubeStart of suggested clipEnd of suggested clipYou can do this by lining up the fitting barbed end to the end of the tubing you are using marking.MoreYou can do this by lining up the fitting barbed end to the end of the tubing you are using marking. The area where the clamp will be connected sliding the clamp onto the tubing.

How do you fix a cracked fuel line?

0:4610:40How To Fix Leaking Fuel Lines | ALL Makes And Models - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then our tubing now you can either use steel tubing or you can use this nickel copper alloy thisMoreAnd then our tubing now you can either use steel tubing or you can use this nickel copper alloy this stuff bends a lot easier it's not that much more expensive i'm gonna put all this stuff in the

Can I use JB Weld on a fuel line?

When fully cured, J-B Weld is completely resistant to water, gasoline, and about every other petroleum product or automotive chemical.

Can I use rubber hose to repair fuel lines?

Standard rubber vacuum or heater hose should never be used in fuel applications. The hose will deteriorate from the inside out and can plug fuel filters and carburetors with rubber debris, long before it springs an external leak.

How do you soften nylon hose?

Boiling water usually works, but don't dip too much of the end into it else you no longer have a stiff tube to push, it also takes a minute in the water to soften it.

Will flex seal work on a fuel line?

No, Flex Seal is not resistant against a corrosive flammable like gas or oil. It is strongly recommended that you do not attempt to use Flex Seal Liquid™ on a gas tank.

Is epoxy resistant to gasoline?

Loctite Epoxy Weld does not shrink and is resistant to most shop fluids such as water, diesel fuel, gasoline, antifreeze, hydraulic fluid, motor oil and transmission fluids.

What is the best material for fuel lines?

The best fuel line material depends on your needs. However, the best material for fuel lines is polytetrafluoroethylene or PTFE. PTFE fuel line is made of plastic material specifically known as Teflon. This fuel line material is impervious is resistant to the degenerative fuel effects which could form vapor barriers.

How strong is J-B Weld on plastic?

STRENGTH: J-B Weld PlasticWeld has tensile strength of 3900 PSI. SURFACE APPLICATIONS: Plastic & PVC, Fiberglass, Glass, ABS, Composites and Vinyl.

Can you epoxy a fuel line?

Permatex makes an epoxy putty specifically for fuel tanks. The key is getting the surface clean and dry, and folding it over enough times to get the two parts well mixed. It hardens quickly, so once it's fully folded (mixed), you've got about 5 minutes to get it where you want it.

Will J-B Weld fix a leaking gas line?

Supplies. JB Weld also makes a gas tank repair kit, which consists of a tube of epoxy putty, fiberglass cloth, sandpaper, and an applicator. This repair is the same as the SteelStik, but adds some additional strength with the fiberglass. This is best used in larger repairs or on a tank with multiple pinhole leaks.