gm fuel line fittings

by Dariana O'Connell Published 3 years ago Updated 3 years ago

What are fuel line adapters and connectors?

Dorman Fuel Line Adapters and Connectors allow you to replace only the damaged fuel line section, not the entire fuel line, saving time and money. These adapters and connectors are easy to install, made of durable steel or nylon, resist rust, corrosion, warping, cracking and are leak resistant.

How many fuel line replacement kits are left in stock?

Only 10 left in stock (more on the way). . . . The Stop Shop Nylon or Steel Fuel Line Replacement Kit. Fittings/Tubing / Compression Fittings. 25' 8 mm Fuel line tubing . Only 11 left in stock - order soon.

What size fuel line do I need to clean fuel line?

I used inch wide by two feet long sand paper with cloth back to clean up the steel fuel line. 3/8 inch. You have to be careful on ordering kits like this as the line may be 3/8 but the fitting may be smaller and will not connect to your filter.

Can the fuel line be bent without the spring?

Despite the product image showing that the kit includes a tube bending spring, there was no spring in the kit. The tube "can" be bent without the spring if you are willing to risk kinking and hence ruining the replacement fuel line section.

What are the types of fuel fittings?

Adapter Fittings Adapter Fittings – also known as Standard Fittings or Union Fittings – are commonly used to connect fuel line tubes and hoses to fuel pumps, fuel regulators, and fuel filters....FYI: Popular fuel line sizes:-6AN (=3/8" OD)-8AN (=1/2" OD)-10AN (=5/8" OD)-12AN (=3/4" OD)

How do you disconnect a GM fuel line connector?

0:134:21And location the push on the other side. So we're going to push this from both directions to releaseMoreAnd location the push on the other side. So we're going to push this from both directions to release it from the use. This type of push connector only pushes from one side as you can see the location.

What size is the fuel line connector?

Fuel Line Connector Size: 3/8 in.

Can brass fittings be used for fuel lines?

It is common to find brass fittings in the air brake systems, cab controls, fuel systems, engine, transmission, cooling and air tanks on a heavy-duty truck and they meet DOT and SAE requirements. Let's take a deeper look into why brass is an ideal material for this market.

How do you remove a push lock fuel line without a tool?

1:412:43You just pull back into the fuel line here and just with one. Hand. You can see it just pops offMoreYou just pull back into the fuel line here and just with one. Hand. You can see it just pops off there now it just may be a little harder to work because you do have an o-ring inside there.

How do I remove a rusted fuel line fitting?

0:022:00If there is excess rust around the quick connect fitting you may be able to free it up by sprayingMoreIf there is excess rust around the quick connect fitting you may be able to free it up by spraying around the connection. And working the line back and forth.

Are fuel lines NPT?

NPT is a tapered thread common to plumbing connections in North America, and is also the most common thread type in fuel line components.

What size is metal fuel line?

For most recent cars, supply is 5/16" and return and vent are both 1/4".

How are fuel fittings measured?

Place the top of a 1/4-inch wrench with an open end over the fuel line. Slide it carefully over the line so that it fits snugly against the tubing. Read the wrench's measurements to determine the diameter of the fuel line. Place a caliper over the fuel line if the wrench did not give an accurate reading.

Can nylon fittings be used with gasoline?

NYLON FITTINGS Nylon is resistant to a broad range of chemicals including most agricultural chemicals, ammonium compounds, detergents, diesel fuel, ethanol, gasoline, hexane, magnesium sulphate, most sodium compounds, trichloroethylene, and zinc sulphate.

Is it OK to use copper tubing for fuel line?

Copper tubing makes an attractive and permanent oil or fuel line and connections. Here are a few hints that might be helpful in working with copper tubing. To begin with, new copper tubing is much easier to work with than old tubing. This is because it is softer.

Does gas eat through brass?

The finding showed that brass is resistant to corrosion after long hours of contact in chosen liquid fossil fuels. Brass has the highest corrosion rate in petrol, fol- lowed by kerosene and least in diesel. The photomicrographs of the samples after ten days of im- mersion also confirmed this.

Russell Performance 644123 - Russell Push-On EFI Fittings

Fitting, Push-On EFI Adapter, Straight, Male -6 AN, Female Quick-Connect 3/8 in., Black Anodized, Each

Russell Performance 644113 - Russell Push-On EFI Fittings

Fitting, Push-On EFI, Straight, Male -6 AN, Female Quick-Connect, Threaded Cap, 5/16 in., Black Anodized, Each

Earl's Performance 751166ERL - Earl's Performance Vapor Guard OEM Quick-Connect Fuel Rail Adapter Fittings

Fuel Line Adapter Fitting, 3/8 in. Female Quick-Connect, To -6 AN Male AN, Straight, Aluminum, Black Anodized, Each

Earl's Performance 751156ERL - Earl's Performance Vapor Guard OEM Quick-Connect Fuel Rail Adapter Fittings

Fuel Line Adapter Fitting, 5/16 in. Female Quick-Connect, To -6 AN Male AN, Straight, Aluminum, Black Anodized, Each

Russell Performance 644133 - Russell Push-On EFI Fittings

Fitting, Push-On EFI, Straight, Male -8 AN, Female Quick-Connect, Threaded Cap, 3/8 in., Black Anodized, Each

ICT Billet AN808-02B - ICT Billet Fuel Rail Adapter Fittings

Fitting, Fuel Line Adapter, Straight, Black Anodized, 3/8 in. Female Quick-connect, -6 AN Male Threads, Each

ICT Billet AN809-02B - ICT Billet Fuel Rail Adapter Fittings