If all else fails, a GE washer not starting may have a broken part. The following parts require a professional washing machine repair when they fail: Control Panel: If the washer has power but one or more of the control panel buttons don’t respond or illuminate, the control panel requires replacement.
Why won’t my ge washer turn on?
Blown fuses, power surges, and dead wall outlets are also common culprits. Troubleshooting the GE washer is the best way to discover the precise reason why it’s not starting, turning off, or turning on.
Why won’t my Whirlpool washer start?
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
Do all GE washers have a locking door?
Your GE washer’s lid or door will naturally latch closed during usage. If you have a top load washer, your model may not feature a locking mechanism. However, front load GE washers almost always have a locking-door feature to keep the chamber watertight.
Why is my Kenmore Elite washer not turning on?
Once the washer door is closed, the washer can begin operating. If the washer door is not latched shut, the door switch will prevent the washer from operating. If the door lock is defective, the washer will not spin or start.
How do you reset a GE top load washer?
Motor Reset Procedure:Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ... The motor has now been reset and is ready for you to start a cycle.
Is there a reset button on GE washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I put my GE washer in diagnostic mode?
0:236:05How to Find Error Codes, and Reset a GE Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce this is done let's go ahead and start with this code first press and hold the start button onMoreOnce this is done let's go ahead and start with this code first press and hold the start button on the washing. Machine and once this is done turn the main dial counterclockwise or to the left.
How do I troubleshoot my GE top load washer?
How to Troubleshoot a GE Top Load WasherCheck the amount of detergent you have put in the washer. ... Examine the GE top load washer's drain hose for leaks. ... Check the water connections to your GE top load washer. ... Check whether the GE top load washer lid is closing firmly. ... Check the load in your GE top loading washer.More items...
Why is my GE washer not starting?
0:111:52Top-Load Washer Won't Start — Washing Machine TroubleshootingYouTubeStart of suggested clipEnd of suggested clipYou should first determine if the electrical outlet the appliance is plugged into is getting powerMoreYou should first determine if the electrical outlet the appliance is plugged into is getting power if not check to see if the circuit breaker has tripped.
How do I know if my GE washer lid switch is bad?
Signs The Lid Switch Is Bad If the control panel doesn't detect the switch as being engaged, then the washer won't agitate or spin when you close the lid. Your washer may or may not fill with water when you have a bad lid switch depending on the model you have.
How do you start a GE washing machine?
The sequence of operation is:Load clothes.Load detergent and other laundry products that you may need.Press the Power button. ... Select the cycle. ... Press Start.For 15 seconds, the unit's computer checks the system and then locks the door.The basket turns 1/4-turn clockwise, then counter-clockwise and unlocks the door.More items...
How do I reset my washing machine?
1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
What is the signal button on a GE washer?
0:009:00GE Washer Diagnostics Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlready did that so plug it back in and then on this particular model you hit signal rinse signalMoreAlready did that so plug it back in and then on this particular model you hit signal rinse signal now you're in Diagnostics mode then you press enter what just start basically.
Where is the fuse on a GE washer?
0:375:06How To: GE Fusible Link Kit WH49X10055 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow the way on the front panel off we have access to the wiring harness it runs along the cabinetMoreNow the way on the front panel off we have access to the wiring harness it runs along the cabinet here on the right side. Behind this tape is the fuse.
Why is my GE washer not working?
When a GE washer stops working, it could be because of a broken spin belt, a blown fuse, a melted wire, a backed-up water pipe, or a burnt-out power outlet . The most straightforward reason your GE washer isn’t working anymore is that it’s not plugged into a reliable power source.
What happens if my GE washer stops turning on?
If your GE washer suddenly stops turning on, the plug may have fallen out of the outlet. Of course, that outlet might have experienced a short, preventing it from supplying anything with power.
How to check if my washing machine is plugged in?
Firstly, check to see if your washing machine is plugged in. If it is, check your outlet to ensure that it’s functioning correctly. If your outlet passes this test, you’ll likely want to contact an appliance repair technician to help you replace and essential fuses, wiring, or sensors causing trouble.
Why does my GE washer stop?
There are two primary reasons why your GE washer might continually stop during a wash cycle. A triggered door sensor, and. A failed electrical sensor or fuse. Some GE washers allow users to view error codes. If your model has this feature, you may want to check your error codes before moving forward.
Why won't my washer start?
If your washing machine doesn’t start or power on, you may be dealing with a failed fuse or a melted wire. These typically happen after a power surge, though time and usage factor into how long a washer’s wiring lasts.
How to reset a GE washer?
To reset your GE washer, you’ll need to unplug it from its power source. Wait at least 60 seconds before plugging it back in. After that, you may need to input a particular code or lift your washer’s lid a specific number of times to trigger the reset.
Do GE washers have a locking door?
Your GE washer’s lid or door will naturally latch closed during usage. If you have a top load washer, your model may not feature a locking mechanism. However, front load GE washers almost always have a locking-door feature to keep the chamber watertight.
What happens if a washer overheats?
If the washer overheats, the thermal fuse will blow. If the line fuse blows, the washer won’t start. To determine if the thermal fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it.
How to tell if an outlet is not getting power?
If the outlet is not getting power, check the home circuit breakers or fuses.
Why does my washer fuse blow?
The line fuse blows if the washer circuits are overloaded. If the line fuse blows, the washer won’t start. To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. In addition, you should investigate and resolve the problem that caused the fuse to blow.
What to do if your buttons don't work?
Additionally, if the display is not working, check the power to the user control and display board . If the user control and display board has power, but it isn’t working, replace it. Required Part.
How to tell if a timer is defective?
To determine if the timer is defective, consult your washer’s wiring diagram and use a multimeter to test the timer for continu ity.
GE Washer Not Starting: 11 Common Reasons
If your GE washing machine won’t start, then try these troubleshooting steps first before calling a repair person or buying a new washer.
Final Words
Well, you have now examined and tried each of the most likely causes of a GE washing machine not starting. As you can see, there are a few more causes of a washing machine not starting that I did not explain.
Loss of electrical power
Loss of electrical power will affect the washer and it will not spin as you may have a defective fuse or a wall outlet that is not working.
Water level control
If your washer is not spinning but it is washing your clothes and the water pump is pumping water out then the fault can be in water level control.
Thermal fuse
If your GE washer is not working and stuck then it might be due to overheating which also burns out the thermal fuse.
Loss of electrical power
To fix this problem you can check your plug pin. You can also change your fuse and you need to contact an electrician to check your wall outlet.
Water pump
You need to dry the washer because it will not work if there is water in it then u need to clean the water pump properly. If your problem is not solved then you need to change your water pump.
Transmission lock
To check your transmission lock you need to remove the belt from the pulley and rotate the pulley in both directions. If the pulley is not rotating then your transmission is locked and you need to replace your transmission lock.
Thermal Fuse
To fix this problem first you need to check if your thermal fuse is working or not. For that, you need to take your multimeter and check the continuity.
How to reset a GE washer?
Step 1. Do not pull the knob while you turn the dial, just like when you will wash. Step 2. You need to unplug the washer from the power outlet. Step 3.
What happens when a GE washer is not spinning?
The most common symptom of this failed drive motor coupling is that the GE washer is not spinning or agitating, while the washer can fill and drain normally .
Why won't my washing machine spin?
Sometimes, this kind of problem is because someone unintentionally presses the stop or pause button or because of power failure. But most of the time, there are some parts of your washing machine that need to be repaired or replaced. Some part of the general electric washer that usually acts up and causes the washer not to be able to spin ...
How long to wait to turn on a washer after unplugging?
You have to turn it all the way around and stop at any button except the ‘final spin’ position. Step 4. You have to wait for at least 30 seconds after unplugging it. Then plug the washer back into the wall outlet to start the washer back up. Step 5.
What is the agitator in a washing machine?
The agitator in the washing machine is the part that moves the clothes from side to side back and forth through the water and detergent that is moved by the transmission output shaft. If the washing machine’s agitator fails to move back and forth during the wash cycle, the agitator may need to be replaced.
How to test a washer cycle?
Step 7. Insert a cloth (towel or a rag) into the washer. Pull the knob to start the washer. Step 8. You can now test the wash cycle on a small load setting.
Why does my washer keep saying "silence"?
When you hear silence from your general electric washer, it means that there is something wrong with your washer; that you need to check immediately. Sometimes, this kind of problem is because someone unintentionally presses ...