- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ...
- The motor has now been reset and is ready for you to start a cycle.
What should I do if my ge washing machine is stuck?
23/06/2020 · To reset washing machines that use the GE Hydrowave system, start by unplugging the washer for one minute. Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. Raise the lid at least 2 inches and make sure it closes each time. This should complete the motor reset.
Can you reset a GE Hydrowave washing machine?
To reset washing machines that use the GE Hydrowave system, start by unplugging the washer for one minute. Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. Raise the lid at least 2 inches and make sure it closes each time. This should complete the motor reset.
How to reset a general electric washer that stops running?
To reset washing machines that use the GE Hydrowave system, start by unplugging the washer for one minute. Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. You'll need to do this within a 12-second period. Raise the lid at least 2 inches and make sure it closes each time.
How do you reset the controls on a whirlpool washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How to stop a washer cycle?
If there is a pause or interruption of the wash cycle while the washer is in use, this can cause the electronic controls to lock up. A pause or interruption during the wash cycle can occur because of the following situations: 1 A power failure. 2 A new washer was left in test mode while being assembled at the factory. 3 The washer was stopped before the cycle was complete. 4 The stop/pause button was pressed to temporarily stop the cycle and was not reset. In this case, the washer will pump out and spin after 24 hours but the controls may stay stuck in the final spin portion of the cycle.
Why does my washer lock up?
If there is a pause or interruption of the wash cycle while the washer is in use, this can cause the electronic controls to lock up. A pause or interruption during the wash cycle can occur because of the following situations: A power failure.
How long does it take for a washer to stop spinning?
The washer was stopped before the cycle was complete. The stop/pause button was pressed to temporarily stop the cycle and was not reset. In this case, the washer will pump out and spin after 24 hours but the controls may stay stuck in the final spin portion of the cycle.
How to reset a washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Why does my washer keep saying "silence"?
When you hear silence from your general electric washer, it means that there is something wrong with your washer; that you need to check immediately. Sometimes, this kind of problem is because someone unintentionally presses ...
What is the agitator in a washing machine?
The agitator in the washing machine is the part that moves the clothes from side to side back and forth through the water and detergent that is moved by the transmission output shaft. If the washing machine’s agitator fails to move back and forth during the wash cycle, the agitator may need to be replaced.
How to reset a GE washer?
Step 1. Do not pull the knob while you turn the dial, just like when you will wash. Step 2. You need to unplug the washer from the power outlet. Step 3.
Why won't my washing machine spin?
Sometimes, this kind of problem is because someone unintentionally presses the stop or pause button or because of power failure. But most of the time, there are some parts of your washing machine that need to be repaired or replaced. Some part of the general electric washer that usually acts up and causes the washer not to be able to spin ...
What happens when a GE washer is not spinning?
The most common symptom of this failed drive motor coupling is that the GE washer is not spinning or agitating, while the washer can fill and drain normally .
How long to wait to turn on a washer after unplugging?
You have to turn it all the way around and stop at any button except the ‘final spin’ position. Step 4. You have to wait for at least 30 seconds after unplugging it. Then plug the washer back into the wall outlet to start the washer back up. Step 5.
How to test a washer cycle?
Step 7. Insert a cloth (towel or a rag) into the washer. Pull the knob to start the washer. Step 8. You can now test the wash cycle on a small load setting.