- Do not pull the knob while you turn the dial, just like when you will wash.
- You need to unplug the washer from the power outlet.
- Turn the timer button. ...
- You have to wait for at least 30 seconds after unplugging it. ...
- Lift the lid for at least 5 to 6 times 2 inches high and open and close it within 15 seconds.
Full Answer
How do I Reset my GE Profile washer?
- Touch "Control Lock" for five seconds until "CL" disappears from the washer's display to unlock the control panel.
- Press "Start/Pause" to manually pause the cleaning cycle.
- Pull the door's handle to open the door and add or remove the clothing from the washer.
How to troubleshoot a GE Profile washer Spin Cycle?
- Press Start to resume the cycle or you can select Drain & Spin and press Start. ...
- If water remains in the washer, check for a pinched or flattened drain hose. ...
- If you clear a clog, press START to resume your cycle or you can select Drain & Spin and press Start.
- If the water drains, then the clog is clear. ...
How to troubleshoot GE Profile Arctica fridge problems?
GE Profile Arctica Operation Problems. Check first to make sure that the power cord is plugged in to an operating outlet. If the refrigerator is plugged in, check the fuse or breaker for the outlet to make sure that the fridge is getting power. Check the refrigerator controls. Neither of the controls should be set to zero.
How to put Ge top load washer in diagnostic mode?
GE Front Load Washer Service mode
- Entering And Exiting The Service Mode
- Never disconnect the power to the washer while it is in the service mode. Doing so may result in a damaged control board.
- t01
- t02
- Error Codes Test Mode
- t03
- t04
- LED And Buttons Test Mode
- t05
- Water Pump Test Mode
How to reset a washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How to stop a washer cycle?
If there is a pause or interruption of the wash cycle while the washer is in use, this can cause the electronic controls to lock up. A pause or interruption during the wash cycle can occur because of the following situations: 1 A power failure. 2 A new washer was left in test mode while being assembled at the factory. 3 The washer was stopped before the cycle was complete. 4 The stop/pause button was pressed to temporarily stop the cycle and was not reset. In this case, the washer will pump out and spin after 24 hours but the controls may stay stuck in the final spin portion of the cycle.
Why does my washer lock up?
If there is a pause or interruption of the wash cycle while the washer is in use, this can cause the electronic controls to lock up. A pause or interruption during the wash cycle can occur because of the following situations: A power failure.
How long does it take for a washer to stop spinning?
The washer was stopped before the cycle was complete. The stop/pause button was pressed to temporarily stop the cycle and was not reset. In this case, the washer will pump out and spin after 24 hours but the controls may stay stuck in the final spin portion of the cycle.
How to turn off a washer?
Wait for thirty seconds. Now, when the power is cut from the source, press the Start/ Pause button for five seconds.
Why is my washer not working?
However, it might be because of the electronic system pause or entire lock-up that can be backed up by several reasons for other systems. Mostly, the reasons include the power failure or the pause button malfunction, or the pressing of the stop button instead of the reset button. Thereby, whatever may be stuck and your washer not being able ...
Can you go ahead with a washer that is not completing the cycle?
Now, if the washer is ready to go and completing the spins without stucking or any interruption, you can go ahead with your repaired washer and complete the washing process with the clothes. However, if the spinner is still not completing the cycles and is stucking in between, the trouble might be something else.