Receiving Helpdesk

framing for bifold closet doors

by Tiana Conroy Published 3 years ago Updated 3 years ago

Bi-folds are framed same as a typical interior door. For double 24" doors, you would add 5" for the header size. With the trimmer or jack studs installed, that gives you 50" for your width. 82" is typically standard for height, but as handy states, it's dependent on your floor type and how high or low you want the doors off of the floor.

Full Answer

How to install molding for a bifold door?

TOOLS FOR BIFOLD DOOR FRAME TRIM

  • Measuring tape
  • Pencil
  • Saw – I use this Miter saw
  • Paintbrushes
  • Clamps
  • Level
  • Brad nailer – I use the Ryobi 18G Brad Nailer
  • Caulk gun

How to easily install bifold door frame trim?

Mount the Bifold Door Hardware

  • Attach the track to the header of the frame using the mounting hardware.
  • After making sure it's centered, connect the upper pivot to the pivoting side of the frame opening. ...
  • Screw the jamb bracket into the bottom corner of the frame. ...
  • Lay each door panel flat on the ground and push them together to attach the hinges and mounting plates. ...

What is the best material for interior bi-fold doors?

Here are the characteristics of a few popular species: Poplar is an ideal choice because it accepts paints and stains well and is typically inexpensive. Red oak is the most popular and abundant of the hardwoods. ... Ash is slightly harder than red oak and stains well. Hickory is the strongest, heaviest, and hardest of the hardwoods. ... More items...

What style doors are best to use for a closet?

  • Pocket: Pocket doors are masters of saving space. ...
  • Sliding: Similar to the pocket style, sliding doors take up minimal amounts of space. ...
  • Folding: These are a standard choice for your laundry room or closet. ...
  • Panel and flush: The most common type, panel and flush entryways are typically made of wood or MDF. ...

More items...

How do you frame a bifold closet door?

1:325:10How to install a bifold door - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a handsaw cut a flat Jam ensure the flat Jam is slightly smaller than the opening this willMoreUsing a handsaw cut a flat Jam ensure the flat Jam is slightly smaller than the opening this will enable the frame to be pack square. Now with your cordless drill pre-drill a pilot holes.

Do you need a frame for bifold doors?

Not only do they require rails, runners, and other extra components, but they come in a range of different sizes that require a range of different frames. If you're installing a bi-fold door, then you'll likely be replacing an older door frame, or creating a space from scratch, rather than modifying an existing frame.

What is the rough opening for 48 inch bifold doors?

The rough opening should be 49 by 82 for a 48-by-80-inch door. This allows for 1/2-inch-thick drywall on both sides and at the top, 80 inches for the doors and hardware, and a 1-to- 1 1/2-inch space under the door.

What is the rough opening for 30 inch bifold door?

So, if you have a bedroom door that is 30″ wide (which is considered a 2/6 or 2′-6″ door) just add 2″ to the width and frame it 32″ wide. The height is 80″ (which is considered 6/8 or 6′-8″) add 2-1/2″ to the actual door height and frame it 82-1/2″ high.

Do you need a header for bifold doors?

Although a header is not required to support bifold doors, it is a good idea to include one during the framing of the opening. This allows you the versatility of hanging a traditional door if the need ever arises.

How thick are bifold door frames?

The door leaf thickness = 68mm. The outer frame depth = 142mm. 28mm double glazed units in all doors. Please check for current standard glass specification.

Can you use 2/24 bifold doors for a 48 opening?

Two-section bifolds are generally sold in widths to fit openings from 24 to 36 inches. Again, the doors can be trimmed slightly at the sides to fit smaller openings or filler strips can be added to the sides of the opening to close gaps. If an opening is 48 inches wide or wider, two 2-section doors are used to fill it.19-Nov-1987

What size opening do I need for bifold doors?

Typically the rough bifold door opening should be sized 2 inches wider and 2 inches higher than the door itself, regardless of the bifold door size. For example a four-foot wide (48”) by six feet, eight inches high (80”) Bifold set of doors, would require a rough opening width of 50 inches and a height of 82 inches.

Do they make 48 inch bifold doors?

48 x 80 Bifold Doors.

How much should be the gap between bifold doors?

The goal is to adjust the doors to leave an even 1/8-in. vertical gap between them (Photos 1 and 2) and an even horizontal space along the top—without allowing them to scrape on the door jambs or floor. You can't always get the doors perfectly aligned on all four sides, especially if the opening is out of square.30-Jun-2017

What does a 3080 door mean?

Single 3080 – denotes 36” width x 96” height door = 37 ½” x 97 ¼” iron door.

How much space should be between door and frame?

The frame should be 3/16" wider than the slab (1/16" clearance on the hinge jamb and 1/8" clearance on the strike jamb) and tall enough (usually 1/4" - 1/2" taller) to allow 1/8" clearance on the head jamb and allow the slab to operate without rubbing on any flooring.

How wide should a bifold door be?

For example a four-foot wide (48”) by six feet, eight inches high (80”) Bifold set of doors, would require a rough opening width of 50 inches and a height of 82 inches.

Can a bifold door be installed in a wall?

When installing a Bifold door into a wall it is important that the rough opening for the Bifold door be sized correctly. If the rough opening is not sized correctly the Bifold door will either not fit if it is too small , or have wide gaps if it is too large. Find a Local Framing Contractor here. Typically the rough bifold door opening should be ...

What is framing a closet door?

The term "framing" here refers to installing the jambs into a rough opening for bypass or bifold doors. These closet doors are not available as prehung units. A 6-foot-wide closet opening is most common, but you can install closet doors in an opening of just about any width.

How big should a closet header be?

If you do not already have one, build a wall for the closet, with a header above. A header that spans 6 feet should be made of 2x8s or larger , even if it is not load-bearing. Check that the opening is the correct size for the bifold or sliding doors you will install. Measure the diagonals to be sure that the opening is at least within 3/8 inch of square and ensure that the sides are plumb and the header is level.

How high is a bifold door?

The standard height is 80 inches (the same as for an entry door). If you have an older home with 9- or 10-foot-high ceilings, this can leave you with unusable space above the doors.

How deep should I cut a wood floor?

If not, mark a line 3/4 inch from the end. Set a circular saw to cut 1/4 to 3/8 inch deep and make a series of cuts, starting at the line. Remove as much of the wood as you can by tapping gently with a hammer. Clean the joint with a wood chisel. Watch.

Can you remove the floor covering in a doorway?

If you have covered your floor to protect it during construction, remove the covering in the doorway; it's tough to cut around the jamb and trim to remove it later.

How to install a jamb frame?

Insert the jamb frame into the rough opening. Make sure that the jambs are slightly smaller in dimension than the rough opening. Drill the pilot holes on the sides of the jamb to the rough opening. Insert the packers and drive nail the jamb.

How do I install bifold doors?

Ensure you have all the necessary tools, as you will have a lot of measuring to do. Measure the opening to ensure the doors will fit. Install the doors by drilling pilot holes and then securing the door to the space.

How efficient are bifold doors?

Bifold doors are quite efficient at managing space. Unlike a standard door, which swings open, bifold doors open in a confined space due to a track system that slides and folds the doors to create an opening.

Why do bifold doors work?

Bifold doors offer modern convenience because they are quite efficient at space management. Many homeowners prefer these for creating unobstructed access to their closets. When installing these types of doors, you don’t need professional help, as this is a DIY friendly project. If you want to install bifold doors in the rough opening, ...

How big is a bifold opening?

Different Steps You’ll Need For A Drywall Opening. When you first measure, you will measure the rough opening size by increasing the bifold’s height by 2 inches and width by 1 inch. For a rough opening of 48 x 80 inches, the drywall opening will be 49 x 82 inches.

How to check the level of a jamb?

Check the level. Align the spirit level on the jamb vertically to check its level with the ground. If the level is not right, insert the packers in the required areas and recheck them. Measure the opening. Use the measuring tape to check for consistency in the height and width of the installed jambs.

Do bifold doors need a bottom track?

It is also not obligatory to use a bottom track for a bifold door. The installation steps discussed above only use a head track to support the door in place efficiently. For internal bifold doors, plastic, and wood doors, a bottom bracket is not a necessity.

How thick should drywall be for 3/4" jambs?

Allow 1" for each side of the 3/4" jamb boards, but only allow 3/4" per side if you're using prefinished 5/8" jamb stock.

How much height for double 24" doors?

For double 24" doors, you would add 5 " for the header size. With the trimmer or jack studs installed, that gives you 50" for your width. 82" is typically standard for height, but as handy states, it's dependent on your floor type and how high or low you want the doors off of the floor.

Inside: Easily install trim around a bifold door frame to hide the metal track and complete the look

As part of my Hallway Refresh I transformed my bifold linen closet door to look like a barn door for $15 in this DIY Bifold Barn Door tutorial. For this post I will show you how I added trim around the bifold door frame to finish out the door.

STEPS TO COMPLETE BIFOLD DOOR FRAME TRIM

Step 1) First I painted the trim in Extra White from Sherwin Williams. Then I measured the two sides first, marked and cut the trim with my miter saw.

Are there standard bifold door sizes?

There are standard sizes for internal and external bifold doors. Standard bifold door sizes you can install inside your home varies depending on the manufacturer. However, there are basic guidelines that manufacturers must follow when designing standard bifold doors.

What is the rough opening for a bifold door?

The rough opening of a bifold door is approximately 50.8 mm higher and 50.8 mm wider than the door itself, regardless of the size of the bifold door. Most bifold doors do not come with a doorjamb kit or lumbers. So, a good-sized opening will allow you to install a jamb extension or lumber on your door.

What is the rough opening of a 48-inch bifold door?

The rough opening of a 48-inch bifold door is 82-inch (2082 mm) higher and 50-inch (1270 mm) wider. This rough opening allows you to install 0.21 mm-thick drywall at the top and on both sides of the door, a 38.1 mm space under the door, and 2032 mm for the doors and hardware.

How To Measure For Bifold Doors

Bifold doors are easy to install even if you are a novice. The only thing you need to know for a successful installation is the size of the door. You will need a few tools to measure for bifold doors. The actual measuring takes only a few minutes. Below are simple steps you need to follow when measuring for bifold doors:

What sizes of custom-made bifold door sizes are available?

All custom-made bifold doors are designed by manufacturers to measure and can be installed in any door space opening you might have. In most cases, manufacturers of bifold doors tend to be flexible.

Step 1 - Measuring

  • First, measure both the width and the height of the door opening. The frame will probably not be perfectly square, so lots of measurements and write down the smallest measurements. This will allow the doors to open and slide properly, even if they are not square.
See more on doityourself.com

Step 3 - Fixing The Batons

  • Cut the wooden batons to the right size and place them all around the door opening. These batons are important in some cases as they make it possible to fit smaller doors. Use screws to fix the batons to the walls so that they are securely fitted, just ensure that there are enough spaces in-between screws to attach the tracks. Using batons is optional and you will only use this if you ne…
See more on doityourself.com

Step 4 - Fixing The Track

  • Bifold sliding doors move by running along a track. These tracks are often included with the doors, although you can also purchase separate lengths of the track if required. Use a hacksaw to cut the tracks to size so that they fit properly in the open doorway. Nail or screw the track onto the top and bottom of the door openings. Use a spirit level to ensure that the doors will open and close …
See more on doityourself.com

Step 5 - Fitting The Doors

  • Once the frame is fitted and complete, you then need to fit the doors. The doors will slide on pins that move around the track that you have just fitted. These pins are normally spring-loaded, which means they can be put into the tracks by pressing the pins down and then allowing them to spring into the track. Looking for more bifold door advice? Here are some hints and additional info.
See more on doityourself.com

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9